Tactical Power Products 13.5Vdc 10A Power Series User manual

DESIGNED & MANUFACTURED
13.5Vdc 10A Power Series
Installation Manual
MODELS :
TPS13-10DC
TPS13-10DC-B
TPS13-10DC-BD10
TPS13-10DC-BD20
TPS13-10DC-ME
TPS13-10DC-MED10
TPS13-10DC-MED20
TPS13-10DC-MED40
© 2016 The contents of
this manual are copyright
and may not be reproduced
without the written
permission of Tactical
Power Products Pty Ltd.
Engineered for ACCESS

DANGER
HIGH VOLTAGE
CAUTION
Dangerous Voltages Inside !
No user serviceable parts inside
Do not remove covers
Dangerous internal voltages exceeding
400 Volts - DO NOT REMOVE COVERS !
Equipment must be installed & serviced
by suitably qualied service personnel in
a restricted access area.
General
These power supplies are designed for indoor use only.
TPS13-10DC models are high performance, extremely low noise, Dual Channel Switch Mode power supplies offering 13.5Vdc at 10A
continuous.
When operating from mains, these models provide an output of 13.5Vdc ( to power connected equipment) and are configured with a
separate 13.8Vdc battery charging channel. Available battery charge current is 1.4A @ 13.8Vdc (total supply output current 11.4A )
In the event of mains failure, battery voltage is clamped to 13.5Vdc and instantaneously powers the load - this is particularly useful for
powering voltage sensitive loads such as CCTV cameras.. When the mains voltage is restored, batteries are disconnected from the load
and recharging commences automatically.
Output short-circuit and overload protection are provided . Removal of the fault / short circuit condition will return the power supply
to normal operation ( Auto-Reset ).
Model Variants
TPS13-10DC Single 10A Output - Supply only - no cabinet (273L x 145W x 80H )
TPS13-10DC-B Single 10A Output - Medium steel enclosure ( 340W x 436H x 145D mm )
TPS13-10DC-BD10 10 x 1A Outputs - Medium steel enclosure ( 340W x 436H x 145D mm )
TPS13-10DC-BD20 20 x 500mA Outputs - Medium steel enclosure ( 340W x 436H x 145D mm )
TPS13-10DC-ME Single 10A Output - Large steel enclosure ( 482W x 470H x 185D mm )
TPS13-10DC-MED10 10 x 1A Outputs - Large steel enclosure ( 482W x 470H x 185D mm )
TPS13-10DC-MED20 20 x 500mA Outputs - Large steel enclosure ( 482W x 470H x 185D mm )
TPS13-10DC-MED40 40 x 250mA Outputs - Large steel enclosure ( 482W x 470H x 185D mm )
Connection
Single Output Models Multiple Output Models
10-way removable terminal block provides the following:
( See over the page for a layout )
* 13.5Vdc Output
* 13.8Vdc Output for SLA (Sealed Lead Acid) Batteries
* Battery Test load (not used on this model)
* AC OK Relay Output ( SPST )
* Battery Fault/Low Battery Relay Output ( SPST )
13.5Vdc Output is via individually fused outputs ( 10, 20 or 40 )
10-way removable terminal block provides the following:
( See over the page for a layout )
* 13.8Vdc Output for SLA (Sealed Lead Acid) Batteries
* Battery Test load (not used on this model)
* AC OK Relay Output ( SPST )
* Battery Fault/Low Battery Relay Output ( SPST )
Caution when handling batteries:
TPS13-10DC_Rev B.pdf www.tacpower.com.au

DESIGNED & MANUFACTURED
O
Rear View
P
AOutput Terminals ( Multi Output models only ) BPDM Input ( Multi Output models only ) - “ I ” below
CIndividual Circuit Status LEDs ( Multi Output Models ) DIndividual Circuit Fuses ( Multi Output models only )
EAC Mains OK Output ( COM / NC ) FBattery Low / Fault Output ( COM / NC )
GNot used in this model H- Battery + (Connect Sealed Lead Acid Battery)
I- Output 13.5Vdc + ( Connect to load or PDM ) JNot used in this model
KBattery Test Fail LED ( Red ON = Fail ) LBattery Fuse Fail LED ( Red ON = Fail )
MAC Mains OK LED ( Green ON = OK ) NReverse Battery LED ( Red ON = Fail )
O240V IEC Mains Socket PCompliance / Date of Manufacture Label
LAYOUT
TPS13-10DC_Rev B.pdf
E F G H I
J K L
M N
A
B
C
D
Multi-Output Models TPS13-10DC Module Face
( e.g. TPS13-10DC-BD10 )
www.tacpower.com.au

Designed & Manufactured
10DC 10DC-B 10DC-BD10 10DC-BD20 10DC-ME 10DC-MED10 10DC-MED20 10DC-MED40
Output Voltage 13.5 Vdc
Output Current 10A Continuous
Output Channels 1 1 10 20 1 10 20 40
Output per Channel 10A 10A 1A 500mA 10A 1A 500mA 250mA
Input Voltage 240 V ac ( +6% / -10% ) 50Hz
Input Current 1.4A @ full load
Input In-Rush Current <20A ( 250C cold start up )
Battery Charger 13.8Vdc / 1.4A
Low Battery Indicator 1 x SPST relay & Red LED
AC Input Indicator 1 x SPST Relay & Green LED
Weight <2Kg <5Kg <5Kg <5Kg <12Kg <12Kg <12Kg <12Kg
Dimensions 273L x 145W
x 80H 340W x 436H x 145D mm 482W x 470H x 185D mm
Efficiency 83% at rated load
Overload Protection Constant current limiting, short circuit shutdown, auto recovery
Load Regulation < 1% from open to full load
Line Regulation < 0.2%
Output Ripple 25mV p-p @ full load
Working Temperature 0 - 500C
Revision B
Safety Standards AS NZS 60950:2011
EMC Standards AS/NZS CISPR 11:2004 ( Class B Conducted and Radiated )
Specications : ( In the interests of product improvement, Tactical reserves the right to change specifications without notice)
Tel: [phone] PO Box 90 Kurrajong NSW 2758 [e-mail]
Securing Your Power Needs ®
Now and into the Future . . .
www.tacpower.com.
13.5Vdc
10A Series
®