tactio INEO-GW0802G User manual

INEO-GW0802G
Switch 8-Port 10/100/1000T
with 2-Port Gigabit Combo SFP
Web Management Function
Quick Installation Guide
FCC Warning
This device has been tested and found to
comply with limits for a Class A digital device,
pursuant to Part 2 and 15 of FCC Rules.
These limits are designed to provide
reasonable protection against harmful
interference when the equipment is operated
in a commercial environment. This
equipment generates and radiates radio
frequency energy and, if not installed and
used in accordance with the user’s manual, it
may cause interference in which case users
will be required to correct interference at their
own expenses.
CE Warning
This is a Class A product. In a domestic
environment, this product may cause radio
interference in which case the user may be
required to take adequate measures.
Introduction
The Switch provides 8 10/100/1000Mbps
NWAY RJ-45 ports and can support 2 Combo
Gigabit SFP Open Slot to uplink. It is
designed for easy installation and high
performance in an environment where traffic
on the network and the number of user
increased continuously. With the newest
Gigabit chip set, Gigabit Ethernet switch can
fully support the highest speed without
hanging on problem even when Full-Duplex
is fully loaded.
The switch also provides automatic crossover
detection functionality on each port. It is
simple and friendly to up-link to another
switch without crossover cable.
This is specifically designed for medium to
large workgroups. The Switch can be installed
where space is limited; moreover it provides
smooth network migration and is easy to
upgrade the network capacity.
Key Features
 Complies with the IEEE802.3 Ethernet,
IEEE802.3u Fast Ethernet and IEEE
802.3ab/z Gigabit Ethernet Standards
 Provides 8 10/100/1000Mbps Gigabit
switching ports and 2 Combo Gigabit SFP
Open Slot
 Non-blocking & Non-head-of-line blocking
full wire speed forwarding
 Store-and-forward operation support
 Embedded 176K Bytes packet buffer
 Provides 8K MAC address entry
 Supports broadcast storm filtering
 All ports provide Auto-Negotiation and Auto
-MDI/ MDI-X functions
 Supports flow control: back pressure for
Half-duplex and IEEE 802.3x for Full-duplex
mode
 Smart plug & play
 Optional: 19” rack-mount Kits
Package Contents
Before you start to install this Switch, please
verify your package contain the following
items:
 One Gigabit Switch
 One AC Power Cord
 One CD ( User’s Manual )
Note: If any of these items is missing or
damaged, please contact your local supplier for
replacement.
Front Panel (LEDs)
LED Indicators of 8 Port + 2 Combo
Gigabit SFP Open Slot Ethernet Switch
LED Status Description No. Of
LED
Power On Power on Power
1000M On 1000Mbps 1-8
off 10/100Mbps
Link/ ACT
On Link 1~8
Flashing Data activating
1~8
SFP
status
On SFP Module is
connected 7FX,8FX
Off SFP Module is
disconnected 7FX,8FX

Connections
Switch/Hub to this 8 Port + 2 Combo
Gigabit SFP Open Slot Ethernet Switch
This switch provides automatic crossover
detection functionality for any port. It is
simple and friendly to up-link to another switch
without crossover cable.
PC/Other devices to this 8 Port + 2
Combo Gigabit SFP Open Slot Ethernet
Switch
Via a twisted pair cable straight through, this
switch can be connected to PCs, servers and
other network devices.
Rear Panel (Power)
AC input
AC input (100~240V/AC, 50~60Hz)
‘
Technical Specifications
Standards
IEEE 802.3 10BaseT
IEEE 802.3u 100BaseTX
IEEE 802.ab 1000BaseT
IEEE 802.3x Flow Control
IEEE 802.1x Port-based
Network Access Control
IEEE 802.1Q VLAN
IEEE 802.3ad Link
Aggregation
IEEE 802.1d Spanning tree
protocol
IEEE 802.1w Rapid Spanning
tree protocol
IEEE 802.1p Class of service,
Priority Protocols
Features
Number of Ports:
10/100/1000BaseTX with
RJ-45 Connectors: 8
Combo SFP Open Slots: 2
MAC Address: 8K
Buffer Memory: 176K Bytes
Method: Store and Forward
Filtering/
Forwarding
Rates
1000Mbps port – 1,488,000pps
100Mbps port – 148,800pps
10Mbps – 14,880pps
Transmission
Media
10BaseT Cat. 3, 4, 5 UTP/STP
100BaseTX Cat. 5 UTP/STP
1000BaseT Cat. 5E UTP/STP
LED
Indicators
LINK/ACT : Per Port
1000M : Port 1~8
SFP Link: 7FX, 8FX
Per Unit: Power
Power
Requirement 100~240V/AC, 50~60Hz
Power
Consumption 20 Watts (Max)
Dimensions 288 × 124 × 44 mm
(L x W x H)
Weight 1.5 kg
Operating
Temperature 0 to 45℃
Storage
Temperature -20 to 90℃
Humidity 10 to 90% RH
(non-condensing)
Certifications FCC Class A, CE