tactio INEO-SU2402G User manual

INEO-SU2402G
Switch 24- Port 10/100TX with
2-Slot MGBIC or 2-Port 1000TE
User’s Manual
FCC Warning
This device has been tested and found to
comply with limits for a Class A digital device,
pursuant to Part 2 and 15 of FCC Rules.
These limits are designed to provide
reasonable protection against harmful
interference when the equipment is operated
in a commercial environment. This
equipment generates and radiates radio
frequency energy and, if not installed and
used in accordance with the user’s manual, it
may cause interference in which case users
will be required to correct interference at their
own expenses.
CE Warning
This is a Class A product. In a domestic
environment, this product may cause radio
interference in which case the user may be
required to take adequate measures.
Introduction
The Switch provides 24 10/100Mbps NWAY
RJ-45 ports and can support 2 Combo
Gigabit Copper/SFP to uplink. It is designed
for easy installation and high performance in
an environment where traffic on the network
and the number of user increase
continuously. With the newest Gigabit chip
set, 19” Gigabit Ethernet switch can fully
support the highest speed without hanging on
problem even when Full-Duplex is fully
loaded.
The switch also provides automatic crossover
detection functionality on each port. It is
simple and friendly up-link to another switch
without any crossover cable.
The rack-mount size is specifically designed
for medium to large workgroups. The Switch
can be installed where space is limited;
moreover it provides a smooth network
migration and easy upgrade a network
capacity. The 19” size can be rack-mount into
19” cabinet.
Key Features
 Complies with the IEEE802.3 Ethernet,
IEEE802.3u Fast Ethernet and IEEE
802.3ab/z Gigabit Ethernet Standards
 Provides 24-port 10/100Mbps + 2 Combo
Gigabit SFP/UTP
 19” rack-mount size
 Non-blocking & Non-head-of-line blocking
full wire speed forwarding
 Store-and-forward operation support
 Embedded 2.75 Mb packet buffer
 Provides 4K MAC address entry
 Supports broadcast storm filtering
 All ports provide Auto-Negotiation and Auto
-MDI/ MDI-X functions
 Supports flow control: back pressure for
Half-duplex and IEEE 802.3x for Full-duplex
mode
 Smart plug & play
Package Contents
Before you start to install this Switch, please
verify that your package contains the following
items:
 One Switch
 Rack-mount Kit for Rack Installation
 One AC Power Cord
Note: If any of these items is missing or
damaged, please contact your local supplier for
a replacement.
Front Panel (LEDs)
LED Indicators of 24-Port 10/100M + 2
Combo Gigabit SFP/UTP Ethernet Switch
LED Status
Description No. Of
LED
Power On Power on Power
10/100M
On Link 10/100Mbps
24 (1~24)
1000M On Link 1000Mbps 2 (25~26)
off Link 10/100Mbps
Link/ ACT
On Link 26 (1~26)
Flashing
Data activating 26 (1~26)

Connections
Switch/Hub to this 24-Port 10/100M + 2
Combo Gigabit SFP/UTP Ethernet
Switch
This switch provides automatic crossover
detection functionality for any port. It is
simple and friendly up-link to another switch
without any crossover cable.
PC/Other devices to this Ethernet
Switch
Via a twisted pair cable straight through, this
switch can be connected to PCs, servers and
other network devices.
Rear Panel (Power)
AC input (100~240V/AC, 50~60Hz)
Technical Specifications
Standards
IEEE 802.3 10BaseT
IEEE 802.3u 100BaseTX
IEEE 802.3ab 1000BaseT
IEEE 802.3z 1000BaseX
IEEE 802.3x Flow control
Features
Number of Ports:
10/100BaseTX with RJ-45
Connectors: 24
10/100/1000BaseT with RJ-45
Connectors: 2
Combo SFP Open Slots: 2
MAC Address: 4K
Buffer Memory: 2.75 Mb
Method: Store and Forward
Filtering/
Forwarding
Rates
1000Mbps port – 1,488,000pps
100Mbps port – 148,800pps
10Mbps – 14,880pps
Transmission
Media
10BaseT Cat. 3, 4, 5 UTP/STP
100BaseTX Cat. 5 UTP/STP
1000BaseT Cat. 5E UTP/STP
LED Indicators Per Port: LINK/ACT
Per Unit: Power
Power
Requirement 100~240V/AC, 50~60Hz
Power
Consumption 20 Watts (Max)
Dimensions 440 × 220 × 44 mm
(L x W x H)
Weight 3.1 kg
Operating
Temperature 0 to 45℃
Storage
Temperature -20 to 90℃
Humidity 10 to 90% RH
(non-condensing)
Certifications FCC Class A, CE