Changing the programming code
Enter the programming code: if not changed is: 123456 confirm with *, the green led will
link.
now the following sequence should e entered: memory cell num er 99 , new programming
code ,and for verification again the memory cell num er 99, the same new programming
code. Confirm with *.
Now you can add access codes in cells 01-98 as descri ed or exit.
To finish press:
֠
֠֠
֠
.
For example changing the programming code to: 649731.
Press: 123456 *, 99 then 649731
and again 99 and 649731 confirm with *.
To finish press:
֠
֠֠
֠
.
You should keep this code because this is the only way to enter the programming
mode!
Back to Initiate status – default
Using an internal jumper the initial programming code can e restored. The access codes will
not e changed.
Turn the power off. dismount the panel. Install a jumper on pins la eled: DEFAULT turn on
the power, a long “Beep” will e sound for confirmation.
Turn off the power and take out the jumper. Reinstall the panel.
The Intercom Encoder returns to normal condition. The Programming code now is: 123456 *.
Canceling an access code
A particular access code could e cancel if its memory cell location is known.
Enter the programming code: if not changed is: 123456 *, the green led will link.
now the following sequence should e entered: memory cell num er to cancel(2 digits), and
֠
֠֠
֠
֠
֠֠
֠
.for verification again the same memory cell num er, and
֠
֠֠
֠ ֠
֠֠
֠
. Confirm with *.
For example: canceling the code stored in cell num er 37:
press the following sequence: ⇒123456 *, 37
֠
֠֠
֠ ֠
֠֠
֠
37,
֠
֠֠
֠ ֠
֠֠
֠
*.
To finish press:
֠
֠֠
֠
.
Setting opening times alues
A different opening time value can e set to opening via the key oard and via the optional
ypass push utton.
The times values are from 1 second till 9 seconds.
Enter the programming code: if not changed is: 123456 *, the green led will link.
now the following sequence should e entered: memory cell num er 00, opening time via
key oard (1 digit) followed y opening time via ypass push utton (1 digit). for verification
repeat the same sequence of memory cell num er 00 opening times values. Confirm with *.
To finish press:
֠
֠֠
֠
.
Remark: when setting the key oard opening time, a value to the ypass push utton must e
set also, even if not installed.
For example setting the key oard opening time to 5 sec. And push utton to 7 sec.
Press: 123456 *,00 then 5 then 7
and again 00 and 5 and 7 confirm with *. To finish
press:
֠
֠֠
֠
.
Summery and examples
Programming option execution default
Entering programming code ⇒ 123456 *
Changing programming code
For example: new code 777456
Enter programming code, *
⇒ 99-777456 99-777456 *
֠
֠֠
֠
123456
Storing a new access code
For example: cell num er 01
access code: 2040
Enter programming code, *
⇒ 01-2040 01-2040 *
֠
֠֠
֠
All the cells are empty
(not 0)
Canceling access code stored in
cell num er 37
Enter programming code, *
⇒ 37-
֠
֠֠
֠ ֠
֠֠
֠
37-
֠
֠֠
֠ ֠
֠֠
֠
*
֠
֠֠
֠
Setting opening time from
key oard to 2 seconds and from
ypass push utton to 5 seconds
Enter programming code, *
⇒ 00-25 00-25 *
֠
֠֠
֠
3 seconds from
key oard,
3 seconds from ypass
push utton
