Tador Doorphone User manual

Tador Technologies Doorphone User guide
1
General:
The Doorphone unit is an intelligent telephone connected
to a telephone exchange, mounted on office entrance and
enables visitors to call to a predefined extension.
Person receiving a call from the door panel can speak with the visitor
and open the door from his telephone extension by pressing a
particular key.
Open the door from the inside is possible by pressing
a bypass pushbutton.
Features:
Easy installation, programming and
operating. Power failure resistance, keeps the programmable values in nonvolatile memory.
Controls a safety camera. Can be programmed from any extension.
Programmable extension key to open door Ability to control 2 entrance doors instead of
the camera.
Every extension can open the door by
pressing a key. optional bypass exit pushbutton
Anti vandal resistance.
Specifications:
Operating voltage: AC 12V 1000mA Opening time: 1-99 seconds
Operating electric or magnetic lock. (normally
open or normally close) Size: under plaster 195X115X50mm (H*W*D) On the wall 154X100X35mm (H*W*D)
Color: silver or bronze
Installation:
According to the door lock type,3 pins connector JM1 should be set
Desirable DOOR state when entering valid code Jumper JM1
Close circuit (Normally open) for electric lock Jumper on 2 left pins (default
state)
Open circuit (Normally close) for magnetic lock One Jumper on 2 right pins
After installing the lock in the door frame. Route the following wirings to the Doorphone:
1. 2 wires from power supply.
2. 2 wires from the lock.
3. 2 wires from a telephone exchange free extension.
4. 2 wires from optional bypass pushbutton.
Using Phillips screw driver open 4 top cover’s screws, carefully pull up the panel.
Using a screw driver, expose the 4 covered insulations bores and the round wirings bore.
Attach the base of the Doorphone to the wall, using a pencil mark the 4 fixing points.
Drill the 4 fixing points on the wall.
Route the wires through the round bore in the base of the Doorphone.
Using 4 screws install the base to the wall.
Verify the power supply is not connected to power source!
Connect the wires to circuit board terminals according to the circuit’s labels, the attached
electrical diagram and the following instructions.
Connect: Power supply to the two 12VAC terminals.
To connect an electric lock: One wire from the lock to the RELAY terminal. The second wire
from the lock to one of 12VAC terminals. Short wire from the second 12VAC terminal to the
second RELAY terminal.
(the RELAY functions as a switch)
If you intend to install a bypass pushbutton, connect it between RMT terminal and the +V
terminal.
2 wires from telephone exchange free extension to LINE.
the polarity of the wires is non significant.

Tador Technologies Doorphone User guide
2
Reassemble the panel over the base.
Attach the top cover to the base using the 4 screws.
Connect the power supply to the power inlet, Initiation tune will be sound.
Technician Programming:
Programming is possible via any extension only.
Entering to programming mode:
oCall the Doorphone's extension from any extension.
oType twice the number sign (##) wait for the confirmation beep.
The following values could be modified:
oSpeed dial when pressing the button
Implementation: type the cell number: 50
Type the telephone or extension number, up to 15 digits.
You can force breaks in the sequence of dialing by inserting *between digits.
Type # to confirm. A confirmation beep sound will be heard.
oDelay time: delay time from the moment a press on the bypass pushbutton was detected,
till the moment the electric lock starts activating. (suitable for situations where there is a
distance between the Doorphone and the door)
Implementation: type the cell number: 01
Type the new delay value's 2 digits. (default 0 seconds)
Type # to confirm. A confirmation beep sound will be heard.
oOpening time: the amount of time the lock stays unlatched.
Implementation: type the cell number: 02
Type the new opening time value's 2 digits. (default 3 seconds)
Type # to confirm. A confirmation beep sound will be heard.
oConversation time: the amount of time you can speak with the Doorphone till it hangs up.
If the value is smaller than 90 or equal, it represents seconds.
If the value is larger than 90, the second digit represents time in minutes.
The value is stored in cell #11, default value 60 seconds.
Implementation: type the cell number: 11 followed by the new value's 2 digits.
Type # to confirm. A confirmation beep sound will be heard.
oNumber of calling rings: the number of rings till the Doorphone answers when calling it.
Implementation: type the cell number: 12
Type the new calling rings value's 2 digits. (default 1 ring)
Type # to confirm. A confirmation beep sound will be heard.
oopening keys from an extension: this is the key enables opening the door from remote.
Because the Doorphone can control 2 doors (the camera must be disabled by setting
"camera time" to 0) a different key must be set to each door. (incase a similar value is
set to the 2 doors, the opening key will open only the first door)
If only one lock is connected, the opening key should be typed twice.
The value is stored in cell #13, default value 7 to the first door and 5 to the second
(CAM terminals).
Implementation: type the cell number: 13
Type 2 digits the first stands for the first door and the second digit for the second door.
If only 1 door is used type the same digit twice.
Type # to confirm. A confirmation beep sound will be heard.
oCamera time: the amount of time the camera stays on (the camera turns on
automatically after pressing the button or calling the Doorphone)
If instead of a camera a second lock is needed – this cell must be reset to 00, in this case
both locks will have the same opening time value.
The value is stored in cell #14, default value 30 seconds
Implementation: type the cell number: 14
Type the new Camera time value's 2 digits.
Type # to confirm. A confirmation beep sound will be heard.

Tador Technologies Doorphone User guide
3
Exit programming mode - type twice on the number sign ## or wait for 10
seconds.

Tador Technologies Doorphone User guide
4
Initiating the Doorphone
It is possible to reset the Doorphone's memory: clear the speed dial, and restore default
values.
Implementation:
oDisconnect the power supply from the Doorphone.
oInstall 2 jumpers, the first on DEF connector between the central pin and the pin
above it. The second between drills PRG (the PRG drills are located below connector
DEF)
oConnect the power supply to the Doorphone.
oWait about 3 seconds till the tune stops indicating completion of the process.
oPull out the jumper from drills PRG.
oReinstall jumper on connector DEF between the central pin and the pin below it.
Connecting a second door latch instead of a camera
In order to set the following parameters refer to the technician and user programming modes
oSet the cell "Camera time" value to 0.
oSet a different "opening key from an extension" to the second door.
oConnect the lock's wires between the CAMRA terminals. The opening will behave
according to jumper JM1: Normally Open or Normally Close.
The Opening and Delay times set to the first lock applicable the second.
Speaker volume adjustments
The Doorphone unit leaves the manufacturer site adjusted.
Sometimes because of the location (opened or closed space), acoustical problems occur.
If the Doorphone’s speaker sound level is too high or low, gently rotate the internal SPK
potentiometer.
Operating:
Visitor
Press the button, identify yourself with the person you are talking with. If your access is
authorized the door lock will buzz, you can pull the door and enter.
When leaving press on the bypass pushbutton, the door lock will buzz, and be unlatched
you can push the door and exit.
Responding to a door call
When a door call ringing tune is sound in your phone, pick up the phone, interview the visitor
up to one minute, after one minute the line disconnected, if authorized press the opening key
(default=7) if the visitor is not welcomed press 0to hang up.
Hanging up the hand set without pressing the opening or hanging key, will cause the
Doorphone's line to stay open till the termination of Conversation time value.
Initiating a call to the Doorphone
Type the Doorphone's extension number.
You can speak with the visitor and open the door.

Tador Technologies Doorphone User guide
5
2010