Taie FY400 User manual

Digital Temperature Controller
FY400/600/700/800/900
FA230/231
Operation Manual
8.8.8.8
8.8.8.8
8.8.8.8
8.8.8.8
8.8.8.8
8.8.8.8 8.8.8.8
8.8.8.8 8.8.8.8
8.8.8.8
Ver 1.3
TAIE
台灣儀控股份有限公司
TAIWAN INSTRUMENT & CONTROL CO., LTD

1FY operation manual
Content
1. Notice...............................................................................................................................................................4
2. Order Information.............................................................................................................................................5
2.1 FY Order Information.............................................................................................................................5
2.2 FA Order Information.............................................................................................................................5
3. Specifications...................................................................................................................................................6
3.1 FY Specifications...................................................................................................................................6
3.2 FA Specifications...................................................................................................................................7
4. Input Range Table............................................................................................................................................8
5. Packing List & Label Information .....................................................................................................................8
5.1 Packing List Guide ................................................................................................................................8
5.2 Label Guide...........................................................................................................................................9
5.2.1 FY400 ........................................................................................................................................9
5.2.2 FY700 ........................................................................................................................................9
5.2.3 FY600/800/900 ....................................................................................................................... 10
5.2.4 FA230 ..................................................................................................................................... 10
5.2.5 FA231 ......................................................................................................................................11
6. Parts Description........................................................................................................................................... 12
6.1 FY Series............................................................................................................................................ 12
6.2 FA Series............................................................................................................................................ 13
7. Installation..................................................................................................................................................... 14
7.1 FY400 Dimensions............................................................................................................................. 14
7.2 FY600 Dimensions............................................................................................................................. 14
7.3 FY700 Dimensions............................................................................................................................. 14
7.4 FY800 Dimensions............................................................................................................................. 15
7.5 FY900 Dimensions............................................................................................................................. 15
7.6 FA230/231 Dimensions ...................................................................................................................... 16
8. Terminal Arrangement................................................................................................................................... 17
8.1 FY400 Terminal Arrangement............................................................................................................. 17
8.2 FY600 Terminal Arrangement............................................................................................................. 18
8.3 FY700 Terminal Arrangement............................................................................................................. 19
8.4 FY800 Terminal Arrangement............................................................................................................. 20
8.5 FY900 Terminal Arrangement............................................................................................................. 21
8.6 FA230 Terminal Arrangement............................................................................................................. 22
8.7 FA231 Terminal Arrangement............................................................................................................. 23
9. Basic Function Setting .................................................................................................................................. 24
9.1 Changing Input Type .......................................................................................................................... 24
9.2 SV Setting........................................................................................................................................... 24
9.3 Setting PID Values Automatically(Autotuning) ................................................................................... 24
9.4 Setting PID Values Manually.............................................................................................................. 24
9.5 Controlling With ON/OFF Action......................................................................................................... 25
9.6 Alarm Mode Setting............................................................................................................................ 25
9.7 Alarm Value Setting............................................................................................................................ 25

FY operation manual 2
9.8 Controlling With Manual Control......................................................................................................... 26
10. Flow Chart of Parameter Setting................................................................................................................. 26
10.1 Level Operation Mode...................................................................................................................... 26
10.2 Level Operation Diagram ................................................................................................................. 27
10.3 Data Lock Function .......................................................................................................................... 27
10.4 Level 1 (User Level) All Parameters Display.................................................................................... 28
10.5 LEVEL_1 Parameter ........................................................................................................................ 29
10.6 Level 2 (PID Level) All Parameters Display ..................................................................................... 30
10.7 LEVEL_2 Parameter ........................................................................................................................ 31
10.8 Level 3 (Input Level) All Parameters Display ................................................................................... 32
10.9 LEVEL_3 Parameter ........................................................................................................................ 32
10.10 Level 4 (Setting Level) All Parameters Display.............................................................................. 35
10.11 LEVEL_4 Parameter....................................................................................................................... 35
10.12 Parameters Hide/Display Table on Level 4 .................................................................................... 36
10.13 Fast Level All Parameters Display ................................................................................................. 38
10.14 Fast Level Parameter..................................................................................................................... 38
11. Functional Descriptions............................................................................................................................... 40
11.1 PV bias ............................................................................................................................................. 40
11.2 Retransmission................................................................................................................................. 41
11.3 Remote SV ....................................................................................................................................... 42
11.4 Heater Break Alarm .......................................................................................................................... 44
11.5 Dehumidification Function ................................................................................................................ 46
11.6 Motor Valve Control.......................................................................................................................... 47
11.7 RAMP & SOAK................................................................................................................................. 50
11.8 Proportional Control.......................................................................................................................... 53
11.9 Master-Slave communication ........................................................................................................... 54
11.10 Piece Linear Compensation ........................................................................................................... 55
12. Alarm Action................................................................................................................................................ 58
12.1 Alarm Mode...................................................................................................................................... 59
12.2 Alarm Special Setting....................................................................................................................... 61
12.3 Alarm Example................................................................................................................................. 61
13. Programmable............................................................................................................................................. 62
13.1 Parameter......................................................................................................................................... 62
13.2 Key Operation Description ............................................................................................................... 63
13.3 Program Initial Setting...................................................................................................................... 64
13.4 Create Program................................................................................................................................ 65
13.5 Program Execution Flow.................................................................................................................. 67
13.6 Program Setting Example ................................................................................................................ 67
14. Modification of Output Module .................................................................................................................... 68
14.1 Relay Control (1a) ............................................................................................................................ 68
14.2 Relay Control (1c) ............................................................................................................................ 68
14.3 SSR Control...................................................................................................................................... 68
14.4 Linear Control................................................................................................................................... 68

3FY operation manual
14.5 Output Calibration Proccedure Diagram .......................................................................................... 69
14.6 Output Calibration Steps .................................................................................................................. 70
15. Modification of Input Signal......................................................................................................................... 71
15.1 Input modify to thermocouple........................................................................................................... 71
15.2 Input modify to RTD.......................................................................................................................... 72
15.3 Input modify to Linear (4~20mA)...................................................................................................... 73
15.4 Steps For Linear Input Calibration ................................................................................................... 74
16. Zero / Phase Control................................................................................................................................... 75
16.1 1ϕZero Cross Control (SCR module).............................................................................................. 75
16.2 1ϕZero Cross Control (TRIAC module)........................................................................................... 75
16.3 3ϕZero Cross Control (SCR module).............................................................................................. 76
16.4 3ϕZero Cross Control (TRIAC module)........................................................................................... 76
16.5 1ϕPhase Angle Control (SCR module)............................................................................................ 77
16.6 1ϕPhase Angle Control (TRIAC module) ........................................................................................ 77
17. Troubleshooting........................................................................................................................................... 78
18. FY/FA Communication Register Address Table .......................................................................................... 79
19. FY/FA Fast Communication Register Address Table.................................................................................. 80
20. Program Design Table................................................................................................................................. 81
21. Glossary of Characters Used In This Manual ............................................................................................. 83

FY operation manual 4
1. Notice
Warning
1. Beware of Electric Shock!
2. Once controller is activated, do not touch AC power wiring terminals to avoid electric shock!
3. First to confirm power is OFF, before working on the wiring of controller power supply!
4. Before using this product, please read through this operating manual thoroughly to understand the correct usage based on
the fundamentals of its conten.
5. This product can be used in industrial equipment, working terminal, measurement equipment, but not in life-saving-related
medical equipment.
6. In order to ensure safety even if the temperature controller fails, please set up another alarm system or safety redundancy.
Caution
1. Before the controller transmits power, make sure that the position of theAC power assembly leg is correct. Otherwise,
the controller may be seriously damaged after power transmission is initiated.
2. Before powering on, please confirm whether the power supply voltage is in accordance with the controller's specification
(AC 85~265V or DC 24V.) Otherwise, the controller may be seriously damaged after power transmission is initiated.
3. Check if the wiring is connected to the terminal for the correct terminals (Input, Output.)
4. Please use crimp terminals suitable for M3 screws, as shown below:
3.2mm 3.2mm
Torque : 0.4 N.m (4kgf.cm)
5. Do not install the controller in places subject to high-frequency interference, corrosive gases, and high temperature and humidity
(normal working environment: 0 ~ 50°C, 20 ~ 90% RH.)
6. To avoid noise interference, please keep the sensor wiring away from the power cord and the loading power cord.
7. When the thermocouple lead is extended, please use the compensation lead of the corresponding type to this thermocouple.
8. When the RTD lead wire is extended, please use those with lower resistance value. Please use the same wire between the three
Wires.

5FY operation manual
2. Order Information
2.1 FY Order Information
0
CommunicationRemote
0
TRS
1
Alarm
0
Output 2
1
Output 1
None
0
1 Set1
None
0None
0None
0
RS-485B
None
Relay
Voltage Pulse
(SSR Drive)
4~20mA
A
B
C
D
0
1
2
3
4 0~20mA
0~5V
0~10V
1~5V
2~10V
None
Relay
0
0~20mA
0~5V
0~10V
1~5V
2~10V
C
D
Voltage Pulse
(SSR Drive)
4~20mA
A
B
1
2
3
4
4~20mA
0~20mA
0~5V
0~10V
1~5V
2~10V
A
B
C
D
1
2
0Input type
See input
Range
type code
4~20mA
0~20mA
0~5V
0~10V
1~5V
2~10V
A
B
C
D
1
2
M
2 Sets2
33 Sets
C
A
B
HBA
HBA+AL2
HBA+AL2+AL3
0 1
1ϕSCR zero cross control
3ϕSCR zero cross control
Motor valve control
1ϕSCR phase angle control
8
6
7
5
Motor valve
control feedback
Power
AC 85~265VA
A
DC 24VD
Accessories
None
N
N
Terminal CoverT
IP65W
Terminal Cover
+IP65
R
Model
NFY400 48x48mm
NFY600 96x48mm
NFY700 72x72mm
NFY800 48x96mm
NFY900 96x96mm
PNFY400 / 401 48x48mm
PNFY600 96x48mm
PNFY700 / 701 72x72mm
PNFY800 / 801 48x96mm
PNFY900 / 901 96x96mm
NFY900(Red/Green light)
NFY901(Blue/White light)
PNFY900(Program)
Block means optional functions with additional charge
※
HBA : Heater Break Alarm(HBA must use AL1 as alarm relay)
※
3TTL
※Block means optional functions with additional charge.
2.2 FA Order Information
0
Communication
Remote
0
TRS
1
Alarm
0
Output 2
1
Output 1
None
0
1 Set1
None
0None
0None
0
RS-485B
None
Relay
Voltage Pulse
(SSR Drive)
4~20mA
A
B
C
D
0
1
2
3
4 0~20mA
0~5V
0~10V
1~5V
2~10V
None
Relay
0
0~20mA
0~5V
0~10V
1~5V
2~10V
C
D
Voltage Pulse
(SSR Drive)
4~20mA
A
B
1
2
3
4
4~20mA
0~20mA
0~5V
0~10V
1~5V
2~10V
A
B
C
D
1
2
0Input type
See input
Range
type code
4~20mA
0~20mA
0~5V
0~10V
1~5V
2~10V
A
B
C
D
1
2
2 Set2
A
B
HBA
HBA+AL2
0 1
Motor valve control
7
Power
AC 85~265VA
A
DC 24VD
Block means optional functions with additional charge
※
HBA : Heater Break Alarm(HBA must use AL1 as alarm relay)
※
Model
FA230(plug-in-out terminal)
FA231(fixed terminal)
3TTL
PFA230
PFA231
※Block means optional functions with additional charge.

FY operation manual 6
3. Specifications
3.1 FY Specifications
Model
FY400
FY600
FY700
FY800
FY900
Supply Voltage
AC 85 ~ 265V, DC 24V (Optional Functions)
Power Frequency
50/60 Hz
Power Consumption
Approximately 6VA
Memory
Non-Volatile Memory EEPROM
Sensor Input
※Please refer to Input
Range Table
Cold junction compensation diode external
Accuracy : 0.1%
Cold junction compensation diode internal
Accuracy : 0.3%
Sample time : 50ms
Thermocouple : (K, J, R, S, B, E, N, T, W, PLⅡ, L)
RTD: PT100
DC LinearAnalog Input : 0~20mA, 4~20mA
0~1V, 0~5V, 0~10V, 0~2V, 1~5V, 2~10V
0~25mV, 0~50mV, 0~70mV
Output
OUT1 Relay
1a
1c
1c
1c
1c
1a SPST-NO, 250 VAC, 5A (resistive load), electrical life: 100,000 operations
1c SPDT-NO, 250 VAC, 5A (resistive load), electrical life: 50,000 operations
SPDT-NC, 250 VAC, 2A (resistive load), electrical life: 20,000 operations
OUT2 Relay
SPST-NO, 250 VAC, 5A (resistive load), electrical life: 100,000 operations
SSR Driver
ON: 24 V OFF: 0V max. load current: 20mA, with short circuit protection circuit
linear
4~20mA,0~20mA, 0~5V,0~10V, 1~5V,2~10V
Control Method
ON-OFF or P, PI, PID control
Alarm
Alarm 1
1a
1c
1a
1c
1c
1a SPST-NO, 250 VAC, 5A (resistive load), electrical life: 100,000 operations
1c SPDT-NO, 250 VAC, 5A (resistive load), electrical life: 50,000 operations
SPDT-NC, 250 VAC, 2A (resistive load), electrical life: 20,000 operations
Alarm 2
SPST-NO, 250 VAC, 5A (resistive load), electrical life: 100,000 operations
Alarm 3
---
1a
1a
1a
1a
SPST-NO, 250 VAC, 5A (resistive load), electrical life: 100,000 operations
TRS
Re-transmitted
Signal
4~20mA, 0~20mA, 0~5V, 0~10V, 1~5V, 2~10V
Source of Re-
transmission
SV, PV
Accuracy
0.1%
Resolution
14 bit
Remote
SV
Signal
4~20mA, 0~20mA, 0~5V, 0~10V, 1~5V, 2~10V
Resolution
18 bit
controlled by
SV
Motor
valve
Signal
1KΩ, 560Ω
Resolution
18 bit
Controlled by
PV2
Commun
ication
Interface
RS-485 Half duplex Communication MAX. 31 units, MAX. distance 1200 meters
Protocol
Modbus RTU , TAIE
Parity bit
NONE, ODD, EVEN
Data bit
8 bit
Stop bit
1 or 2 bit
Baud rate
2400,4800,9600,19200,38400,57600,115200 bps
Malfunction vibration
10~55 Hz 20m / s2 , for 10 min each in X, Y and Z directions.
Vibration resistance
10~55 Hz 20m / s2 , for 2 hr each in X, Y and Z directions.
Malfunction shock
100m / s2 , 3 times each in X, Y and Z directions.
Shock resistance
300m / s2 , 3 times each in X, Y and Z directions.
Operating Environment
Temperature/Humidity
0 ~ 50°C (in the case of no freezing or condensatioin) / 20% ~ 90% RH
Storage Environment
Temperature
-25 ~ 65°C (in the case of no freezing or condensatioin)
Dimension (mm)
W48 x H48 x D95
W96 x H48 x D95
W72 x H72 x D95
W48 x H96 x D95
W96 x H96 x D95
Weight
Appox.120g
Appox.170g
Appox.150g
Appox.170g
Appox.230g

7FY operation manual
3.2 FA Specifications
Model
FA231
FA230
Terminal
Fixed
Pluggable
Supply Voltage
AC 85 ~ 265V, DC 24V (Optional Functions)
Power Frequency
50/60 Hz
Power Consumption
Approximately 6VA
Memory
Non-Volatile Memory EEPROM
Sensor Input
※Please refer to Input
Range Table
Accuracy : 0.2%
Sample time : 50ms
Thermocouple : (K, J, R, S, B, E, N, T, W, PLⅡ, L)
RTD : PT100
DC LinearAnalog Input : 0~20mA, 4~20Ma
0~1V, 0~5V, 0~10V, 0~2V, 1~5V, 2~10V
0~25mV, 0~50mV, 0~70mV
Output
OUT1 Relay
1a
1c
1a SPST-NO, 250 VAC, 5A (resistive load), electrical life: 100,000 operations
1c SPDT-NO, 250 VAC, 5A (resistive load), electrical life: 50,000 operations
SPDT-NC, 250 VAC, 2A (resistive load), electrical life: 20,000 operations
OUT2 Relay
SPST-NO, 250 VAC, 5A (resistive load), electrical life: 100,000 operations
SSR Driver
ON: 24 V OFF: 0V max. load current: 20mA, with short circuit protection circuit
linear
4~20mA,0~20mA, 0~5V,0~10V, 1~5V,2~10V
Control Method
ON-OFF or P, PI, PID control
Alarm
Alarm 1
1a
1c
1a SPST-NO, 250 VAC, 5A (resistive load), electrical life: 100,000 operations
1c SPDT-NO, 250 VAC, 5A (resistive load), electrical life: 50,000 operations
SPDT-NC, 250 VAC, 2A (resistive load), electrical life: 20,000 operations
Alarm 2
SPST-NO, 250 VAC, 5A (resistive load), electrical life: 100,000 operations
TRS
Re-transmitted
Signal
4~20mA, 0~20mA, 0~5V, 0~10V, 1~5V, 2~10V
Source of Re-
transmission
SV, PV
Accuracy
0.1%
Resolution
14 bit
Remote
SV
Signal
4~20mA, 0~20mA, 0~5V, 0~10V, 1~5V, 2~10V
Resolution
18 bit
controlled by
SV
Commun
ication
Interface
RS-485 Half duplex Communication MAX. 31 units, MAX. distance 1200 meters
Protocol
Modbus RTU , TAIE
Parity bit
NONE, ODD, EVEN
Data bit
8 bit
Stop bit
1 or 2 bit
Baud rate
2400,4800,9600,19200,38400,57600,115200 bps
Malfunction vibration
10~55 Hz 20m / s2 , for 10 min each in X, Y and Z directions.
Vibration resistance
10~55 Hz 20m / s2 , for 2 hr each in X, Y and Z directions.
Malfunction shock
100m / s2 , 3 times each in X, Y and Z directions.
Shock resistance
300m / s2 , 3 times each in X, Y and Z directions.
Operating Environment
Temperature/Humidity
0 ~ 50°C (in the case of no freezing or condensatioin) / 20% ~ 90% RH
Storage Environment
Temperature
-25 ~ 65°C (in the case of no freezing or condensatioin)
Dimension (mm)
W40 x H107 x D43
Weight
Appox.115g

FY operation manual 8
4. Input Range Table
Types of input
Code
Range
°C
°F
Thermocouple
K
K1
01
-50.0~600.0
-58.0~999.9
K2
02
-50~1200
-58~2192
J
J1
03
-50.0~400.0
-58.0~752.0
J2
04
-50~1200
-58~2192
R
R
05
-50~1760
-58~3200
S
S
06
-50~1760
-58~3200
B
B
07
-50~1820
-58~3308
E
E
08
-50~900
-58~1652
N
N
09
-50~1300
-58~2372
T
T1
10
-199.9~400.0
-199.9~752.0
T2
11
-199~400
-326~752
W
W
12
-50~2320
-58~4208
PL
PL
13
-50~1200
-58~2192
L
L
14
-50~800
-58~1472
RTD
PT100
PT1
15
-199.9~850.0
-199.9~999.9
PT2
16
-199~850
-326~1562
PT3
17
0~850
32~1562
Linear
AN1
0~25mV
18
-1.999~9.999
-19.99~99.99
-199.9~999.9
-1999~9999
AN2
0~50mV
19
0~20mA
20
0~1V
21
0~2V
22
0~5V
23
0~10V
24
AN3
0~70mV
25
AN4
4~20mA
26
10~50mV
27
1~5V
28
2~10V
29
5. Packing List & Label Information
5.1 Packing List Guide
FY400/600/700/800/900
1. Temperature Controller…1 unit
2. Mounting frame………….2 units
3. Brief manual……………..1 pcs
FA230/231
1. Temperature Controller…1 unit
2. Terminal cover…………...2 units
3. Brief manual……………..1 pcs

9FY operation manual
5.2 Label Guide
5.2.1 FY400
(4)
(1)
(2)
(3)
No.
Item
Description
(1)
Terminal arrangement
FY400 Terminal Wiring Diagram
(2)
Model number
FY400 model name
(3)
Serial number
TSP19021140001
(4)
Input type
Controller Input Signal and Range
5.2.2 FY700
(3)
(4)
(1)
(2)
No.
Item
Description
(1)
Terminal arrangement
FY700 Terminal Wiring Diagram
(2)
Model number
FY700 model name
(3)
Serial number
TSP20021170001
(4)
Input type
Controller Input Signal and Range

FY operation manual 10
5.2.3 FY600/800/900
(3)
(4)
(1)
(2)
No.
Item
Description
(1)
Terminal arrangement
FY900 Terminal Wiring Diagram
(2)
Model number
FY900 model name
(3)
Serial number
TSP20021190001
(4)
Input type
Controller Input Signal and Range
5.2.4 FA230
(2)
(3)
(4)
(1)
(5) M/N：FA230-30100B
S/N：TSP20021120010
No.
Item
Description
(1)
Model number
FA230 model name
(2)
Input type
Controller Input Signal and Range
(3)
Control output
4~20mA
(4)
Terminal arrangement
FA230 Terminal Wiring Diagram
(5)
Serial number
TSP20021120010

11 FY operation manual
5.2.5 FA231
(2)
(3)
(4)
(1)
(5) S/N：TSP20021120010
M/N FA231-30100B
No.
Item
Description
(1)
Model number
FA231 model name
(2)
Input type
Controller Input Signal and Range
(3)
Control output
4~20mA
(4)
Terminal arrangement
FA231 Terminal Wiring Diagram
(5)
Serial number
TSP20021120010

FY operation manual 12
6. Parts Description
6.1 FY Series
8.8.8.8
8.8.8.8 8.8.8.8
8.8.8.8
8.8.8.8
8.8.8.8
8.8.8.8
8.8.8.8
8.8.8.8
8.8.8.8
FY400
FY900
FY800
FY700
FY600
8.8.8.8
8.8.8.8
1
PV
Indicating PV (measured value) and
character information such as parameter
codes or error codes(Red)
2
SV
Indicating SV (target set value) or
parameter values(Green)
3
LED
OUT1
Lamp lit when OUT1 is activated
(Green )
OUT2
Lamp lit when OUT2 is activated
(Green )
AT
Lamp lit when Auto-tuning is activated
(Orange)
AL1
Lamp lit when Alarm 1 is activated (Red)
AL2
Lamp lit when Alarm 2 is activated (Red)
AL3
Lamp lit when Alarm 3 is activated (Red)
MAN
Lamp lit when controller in manual mode
or get error condition (Orange)
PRO
When the program is executed, this light
is on (orange)
OUT1%
Output% bar-graph indicator(Green)
4
Keypad
SET
For parameter call-up and set value
registration
A/M
Auto manual transfer
SHIFT
Shift digits when changing settings
DOWN
Decrease numerals
UP
Increase numerals

13 FY operation manual
6.2 FA Series
OUT1 OUT2 AL1AL2
FA230 TAIE
8.8.8.8
8.8.8.8
SET
1
PV
Indicating PV (measured value) and character
information such as parameter codes or error
codes(Red)
2
SV
Indicating SV (target set value) or parameter
values(Green)
3
LED
OUT1
Lamp lit when OUT1 is activated ( Green )
OUT2
Lamp lit when OUT2 is activated ( Green )
AL1
Lamp lit when Alarm 1 is activated (Red)
AL2
Lamp lit when Alarm 2 is activated (Red)
1. Lamp lit when Auto-tuning is activated
(Orange)
2. When the program is executed, this light is
on (orange)
COM
Lights when controller response data (Orange)
4
Keypad
SET
SET
For parameter call-up and set value
registration
SHIFT
Shift digits when changing settings
DOWN
Decrease numerals
UP
Increase numerals

FY operation manual 14
7. Installation
7.1 FY400 Dimensions
(Unit: mm)
Dimensions
Individual mounting
7.2 FY600 Dimensions
(Unit: mm)
Dimensions
Individual mounting
t (panel thickness) 1~t~6
Mounting fixture
7.3FY700 Dimensions
(Unit: mm)
Dimensions
Individual mounting

15 FY operation manual
7.4FY800 Dimensions
(Unit: mm)
Dimensions
Individual mounting
7.5FY900 Dimensions
(Unit: mm)
Dimensions
Individual mounting

FY operation manual 16
7.6FA230/231 Dimensions
(Unit: mm)
Dimensions
4 x 4
4 x 4
64.0
86.0
12.0
182.0
214.0
198.0
64.0
64.0
80.0
70.0
Ø
Ø
32.0
43.0
6.0
91.0
107.0
35.0
40.0
32.0
99.0
32.0

17 FY operation manual
8. Terminal Arrangement
Caution
When implementing wiring for the controller power supply, please make sure that the power supply is
turned off to avoid electric shock!
Do not touch the live parts, such as the terminals, while the power is on. Otherwise death or serious
injury may be resulted from short circuit of the contact electrode.
8.1 FY400 Terminal Arrangement
Power supply
AC 85~265V
DC 24V
AL2
A
B
B
INPUT
TC/mV
COMM
T/R (A+)
T/R (B-)
RTD mA/V
1
2
3
4
5
8
11
12
13
14
6
7
9
10
Relay
SSR
mA/V
OUT2
(AL1)
Relay
SSR
mA/V
OUT1
4
5
mA / VSSR
4
5
4
5
Relay
1
6
DC 24V
1
6
AC 85~265V
L
N
2
3
mA / VSSR
2
3
2
3
Relay
11
12
mA / V
11
12
mA / V
TC / mV
9
10
7
9
10 A
B
B
RTD
7
9
10
mA / V
G1
11
12
13
14
K1
K2
G2
13
14
AL2
2
3
11
12
AL1
or
2
3
4
5
CLOSE
COM
OPEN
Power
Output-1
Output-2
1ϕ Zero cross
Motor
valve
Transmission
Remote SV
Input
Alarm-1
Alarm-2
Communication
11
12
CT
CT
RS-485
11
12 T/R (A+)
T/R (B-)

FY operation manual 18
8.2FY600 Terminal Arrangement
Power supply
AC 85~265V
DC 24VSSR
mA/V
OUT1
NO NC COM
Relay
3 4 5 6 7 8 9 10
11 12 13 16 2017
1 2
Relay
SSR
mA/V
OUT2
(AL3)
NC NO COM
AL1
NC NO COM
AL2ABB
INPUT
TC/mV
RTD
mA/V
COMM
T/R (A+)T/R (B-)
14 15
mA/V
Remote
1918
1
2
DC 24V
1
2
AC 85~265V
L
N
Power
Output-1
Output-2
Motor valve
9
6
7CLOSE
8OPEN
10 COM
14
15
CT
14
15
mA / V
Transmission
Remote SV/
CT Input
Input
Communication
12
13
mA / V
14
15
mA / V
6
7
mA / VSSR
6
7
6
7
Relay
9
NO
NC
COM
8
10
SSR mA / V
9
10
9
10
12 NO
NC
11
13
AL2
COM
6
7
AL3
4NO
NC
3
5
AL1
COM
Alarm 1
Alarm 2
Alarm 3
TC / mV
19
20
17
19
20 A
B
B
RTD
17
19
20
mA / V
RS-485
14
15 T/R (A+)
T/R (B-)

19 FY operation manual
8.3 FY700 Terminal Arrangement
1
2
3
4
5
6
15
16
71421
Power supply
AC 85~265V
DC 24V
13
8
9
10
A
B
B
INPUT
TC/mV RTD mA/V
17
18
12
11
mA/V
TRS 19
20
Relay
SSR
mA/V
OUT2
(AL1)
SSR
mA/V
OUT1
NO
NC
COM
Relay
COM
NO
NC
AL2
COMM
T/R (A+)
T/R (B-)
AL3
9
10
mA / V
18
19
mA / V
1
2
DC 24V
1
2
AC 85~265V
L
N
6
NO
NC
COM
5
7
SSR mA / V
6
7
6
7
3
4
mA / VSSR
3
4
3
4
Relay
3
4
AL1
9NO
COM
8
10
AL2
NC
20
21
AL3
Transmission
Remote SV
Input
Alarm 1
Alarm 2
Alarm 3
Communication
Power
Output-1
Output-2
1ϕ Zero cross/
Phase angle
Motor
valve
CT
Input
15
16
mA / V
18
19
CT
18
19
mA / V
15
16
CT
TC / mV
13
14
11
13
14 A
B
B
RTD
11
13
14
mA / V
G1
15
16 K1
18 K2
17 G2
6
3
4CLOSE
5OPEN
7COM
RS-485
15
16 T/R (A+)
T/R (B-)