Tainet WANpro 2000 User manual

V1.5 07008-00032 2004/03/24
TAINET
WANpro 2000
WAN ACCESS ROUTER
USER'S MANUAL
The Professional Partner
TAINET COMMUNICATION SYSTEM CORP.
Headquarters:
No. 25, Alley 15, Lane 120, Sec. 1. Nei-Hu Rd.,
Taipei 114, Taiwan, R.O.C.
TEL: [phone]
FAX: [phone]
Beijing Branch:
3F, A Building, 113 Zhi Chun Lu,
HaiDian District, Beijing, China
Zip Code: 100086
Tel: [phone]~87
Fax: [phone]

Copyright © 1999 Tainet Communication Corporation.
All rights reserved.
Printed in Taiwan R.O.C.
Notice
This document is protected by the international copyright law. No part of this
publication may be reproduced by any means without the permission of Tainet
Communication Corporation.
TAINET is a registered trademark, and “WANpro 2000” is a trademark of
Tainet Communication Corporation.
Other product names mentioned in this manual are used for identification
purposes only and may be trademarks or trademarks of their respective
companies.
The information provided from Tainet Communication Corporation is
believed to be accurate. Any changes and enhancements to the product and to
the information thereof will be documented and issued as a new release to this
manual.

FCC NOTICE
This equipment has been tested to comply with limits for a digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in
accordance with instruction manual, may cause harmful interference to
radio communication.
If the equipment does cause harmful interference to radio or television
devices, the user is encouraged to try to correct the interference by one or
more of the following advises:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.
The FCC Rule is available from the U.S. government Printing Office,
Washington, DC 20402, Stock NO. 004-00000345-4.
The shielded RS-232 cable is to be used in order to ensure compliance with
FCC Part 15, and it is the responsibility of the user to provide and use
shielded RS-232 cable from NTU to personal computer.
We will not commit to repair this unconditional fault resulting from the user.
The warranty issue will only protect for right operations mentioned in the
manual, and extra charge for this fault might be noticed if necessary.
Any changes of modifications not expressly approved by the grantee
of this device could void the user’s authority to operate the
equipment.

HOW TO USE THIS MANUAL
This section gives you some ideas about how to use this manual effectively.
It includes brief description of the summary chapters and the symbol used
inside the manual.
Summary Chapters
Section Description
Chapter 1 Quick Start.
Describe quick installation for Tainet’s WANpro 2000
device
Chapter 2 Introduction
General introduction to Tainet’s WANpro 2000 device
Chapter 3 Configure and Monitor Via Front Panel
Provide the procedures to setup the user interface and
using LEDs, status to monitor the device via LCD Front
Panel.
Chapter 4 Configure and Monitor Via PCs or Terminals
Provide the procedures to setup the user interface and
using LEDs, status to monitor the device via PCs or
Terminals.
Provide information to view and check the network
conditions.
Appendix A Interface Specifications & Cable Diagrams
Describe the port connectors and interface information.
Appendix B Technical Specifications
Contains physical, electrical and mechanical
specifications.
Glossary Define acronyms and terms used in this manual.

Symbols Have Been Used
There are eight types of the messaging symbols used inside the text. By the
way, users will be warned in conditions during chapters.
The questions from the section
The extra information provided for the user
Stop here to check conditions
Users are prohibit
Break time
How to contact
Warning messages

WARRANTY AND SERVICE INFORMATION
If there is any question, contact your local sales representative,
service representative, or distributor directly for any help needed.
You might use one of the following methods:
nVia the Internet: visit our world wide web site at
http://www.tainet.net
nVia the Sales Representatives:
HQ
No. 25, Alley 15, Lane 120, Sec. 1 Nei-Hu Rd., Taipei, Taiwan
TEL: [phone] FAX: [phone]
E-mail: #[email protected]
URL: http://www.tainet.net
Moscow Branch
111024, Shosse Entuziastov, Building 14, Room 425, Moscow, Russia
TEL: [phone] FAX: [phone]
URL: http://www.tainet.ru
Beijing Branch
3F, A Building, 113 Zhi Chun Lu, HaiDian District , Beijng , China
Zip Code: 100086
TEL: Tel: [phone]~87 FAX: [phone]
E-mail: [email protected]
URL: http://www.tainet.com.cn
Guangzhou Representative Office
TEL: [phone] FAX: [phone]
Shanghai Representative Office
TEL: [phone] FAX: [phone]
Chengdu Representative Office
TEL: [phone] FAX: [phone]

CONTENTS
Copyright
FCC Notice
How to Use This Manual
CHAPTER 1 QUICK START...................................................................1
1.1 How to Begin – the first step for the user.....................................2
1.1.1 Unpacking .........................................................................2
1.1.2 Connecting Power to the Device........................................3
1.1.3 Connecting to the Network ................................................3
1.2 How to Operate and Setup Internet Applications..........................4
1.3 How to Operate and Setup Intranet Applications..........................6
CHAPTER 2 INTRODUCTION...............................................................1
2.1 Tainet’s WANpro 2000................................................................2
2.1.1 Features.............................................................................2
2.1.2 Specifications ....................................................................2
2.2 Applications................................................................................4
CHAPTER 3 Configure and Monitor Via Front Panel............................... 1
3.1 Font Panel ...................................................................................2
3.2 Identify LEDs Light Status..........................................................2
3.3 Rear Panel...................................................................................3
3.4 Front Panel Operation..................................................................3
CHAPTER 4 Configure and Monitor Via PCs or Terminals ...................... 1
4.1 Connect WANpro 2000 to PCs or Terminals................................2
4.2 The ‘Configuration’.....................................................................4
4.3 Main Menu:.................................................................................6
4.4 Configuration Menu ....................................................................6
4.4.1. System...............................................................................7
4.4.2. PPP..................................................................................10

4.4.3 FR....................................................................................11
4.4.4. RIP_Setting .....................................................................12
4.4.5. Routing_Table .................................................................14
4.4.6. Security ...........................................................................17
4.4.7 NAT.................................................................................20
4.4.8 Filter................................................................................23
4.4.9 DHCP..............................................................................26
4.5 Monitor Menu ...........................................................................28
4.5.1 Current_Configuration.....................................................28
4.5.2 Routing_Table .................................................................29
4.5.3 ARP_Table ......................................................................31
4.5.4 Statistics ..........................................................................32
4.5.5 NAT_Buffer.....................................................................35
4.5.6 DHCP..............................................................................36
4.6 Device_Control .........................................................................37
4.6.1 Warm_Start......................................................................37
4.6.2 Restore_Default...............................................................37
4.7 Diagnosis Menu.........................................................................38
4.7.1 Ping.................................................................................38
Appendix A Interface Specifications & Cable Diagrams............................ 1
A1. WAN Interface PinOut List (Female Connectors)........................2
A2. Console Cable RJ-45 – DB-25 Connector PinOut........................3
A3. LAN Interface RJ-45 Connector PinOut......................................3
Appendix B Technical Specifications........................................................ 1
B1 LAN Interface .............................................................................2
B2. WAN Interface ............................................................................2
B3. CONSOLE Interface ...................................................................2
B4. Power..........................................................................................2
Glossary...................................................................................................1

FIGURES
Figure 1.1A Front Panel of the Tainet’s WANpro 2000....................................... 1-2
Figure 1.1B Rear Panel of the Tainet’s WANpro 2000 ........................................ 1-2
Figure 1.2 The Internet Connection over PPP................................................... 1-4
Figure 1.3 The Internet Connection over Frame Relay...................................... 1-5
Figure 1.4 The Intranet Connection over PPP................................................... 1-6
Figure 2.1 Applications to xDSL Series Modem............................................... 2-4
Figure 3.1A Front Panel of the Tainet’s WANpro 2000....................................... 3-2
Figure 3.1B Rear Panel of the Tainet’s WANpro 2000 ........................................ 3-3
Figure 3.2 General Initialized Procedures of the WANpro 2000 Device........... 3-4
Figure 3.3 LCD Menu Tree.............................................................................. 3-6
Figure 4.1 The Console Port Connection to PCs or Terminals .......................... 4-3
Figure 4.2 Main Menu Tree.............................................................................. 4-5
Figure 4.3 Example of WANpro 2000 application............................................ 4-7

QUICK START
1-1
CHAPTER 1
QUICK START
Overview
1.1 How to Begin – the first step for the user
1.1.1 Unpacking
1.1.2 Connecting Power to the Device
1.1.3 Connecting to the Network
1.2 How to Operate and Setup Internet Applications
1.3 How to Operate and Setup Intranet Applications

QUICK START
1-2
1.1 How to Begin – the first step for the user
1.1.1 Unpacking
To check the components that you might have,
Accessory Provided
üTainet WANpro 2000 user's manual
üOne digital interface (refer to DTE interface options)
üPower cord
üRJ-11 cable (S.A only)
üRJ-11 box (S.A only)
The front panel of the WANpro 2000 device contains LCD Screen, LEDs
Signal Indicators and Keypad. The whole figure of the WANpro 2000 Front
panel could be found in the Figure 1.1A.
EXIT VO/DA
ENTER
WANpro 2000
TAINET
WANpro 2000
LAN
LANT
LANR
RTS
CTS
TXD
RXD
LINK
CSR
CST
LCD Screen LEDs Indicators Keypad
Figure 1.1A Front Panel of the Tainet’s WANpro 2000
AC INPUT POWER WAN Console LAN ISDN
Figure 1.1B Rear Panel of the Tainet’s WANpro 2000

QUICK START
1-3
User’s optional interface modules are depending on their applied network
interface. The optional modules of the WAN interface (see Figure 1.1B)
might include V.24, V.35 RS-530 and X.21. The Console port is used to
monitor and operate the device via PCs or Terminals.
User should not change any modules without
permission from the manufacturer.
The inspection of any damages from shipment includes bending or loosing
hardware components, and broken connectors.
To prevent electrostatic discharge (ESD)
damage, user should avoid not open up the
case to avoid touching internal components.
1.1.2 Connecting Power to the Device
The AC power requirement of the WANpro 2000 device is 115/230 VAC
auto-range input. Before you switch on the device, be sure that you plug the
power cord.
It is strongly recommended that you should
also screw a Protective Ground (PG) wire to
the earth to protect your system.
1.1.3 Connecting to the Network
There are several optional interfaces and connectors such as WAN port
(RS-232 Cable), LAN port (RJ-45), ISDN port – unavailable (RJ-45). The
basic connection of devices could be shown in Figure 1.2.
The WANpro 2000 device is working like a Bridge or Gateway DTEs to
communicate remotely through the RJ-45 for LAN port to Ethernet Network
and RS-232 cable to DCEs for WAN port.
For details of using modules, you need to
contact your local sales representative.
PCs or Terminals could be used to setup system configuration or monitor
system status via Console Port. The DCE could be a Modems, ISDNs or
xDSL Series devices and so on that connect to the WANpro 2000 device
through WAN Port (25 DB).

QUICK START
1-4
1.2 How to Operate and Setup Internet Applications
Host
Host
Host
Internet
Service
Internet
PPP
EXIT VO/DA
ENTER
WANpro 2000
TAINET
WANpro 2000
LAN
LANT
LANR
RTS
CTS
TXD
RXD
LINK
CSR
CST
192.72.240.252192.10.25.1 192.72.240.253
WANpro 2000
Ethernet LAN
Figure 1.2 The Internet Connection over PPP
An Example of the Setup Procedures via front panel
Step 1:Under LAN Setup menu:
IP Address = 192.10.25.1
Step 2
:Under LAN Setup menu:
IP NetMask = 255.255.255.0
Step 3: Under WAN Setup menu:
WAN Protocol = PPP
Step 4:Under PPP Setup menu:
Local Address = 192.72.240.252
Step 5:Under PPP Setup menu:
IP NetMask = 255.255.255.252
Step 6: Under PPP Setup menu :
WAN Port Speed = Sync-External
Step 7:Under Routing Table menu:
Default Gateway = 192.72.240.253
Step 8:In an IP network, each host is configured with
its own IP Address and
a Gateway IP address = 192.10.25.1

QUICK START
1-5
Host
Host
Host
Internet
Service
Fram Relay
EXIT VO/DA
ENTER
WANpro 2000
TAINET
WANpro 2000
LAN
LANT
LANR
RTS
CTS
TXD
RXD
LINK
CSR
CST
192.72.240.252192.10.25.1 192.72.240.253
WANpro 2000
Ethernet LAN
Figure 1.3 The Internet Connection over Frame Relay
An Example of the Setup Procedures via front panel
Step 1:Under LAN Setup menu:
IP Address = 192.10.25.1
Step 2
:Under LAN Setup menu:
IP NetMask = 255.255.255.0
Step 3: Under WAN Setup menu:
WAN Protocol = Frame Relay
Step 4:Under FrRelay Setup menu:
Local Address = 192.72.240.252
Step 5
:Under FrRelay Setup menu:
IP NetMask = 255.255.255.252
Step 6: Under FrRelay Setup menu :
LMI type = ANSI T1.617
Step 7: Under FrRelay Setup menu :
DLCI number = 150
Step 8:Under Routing Table menu:
Default Gateway = 192.72.240.253
Step 9:In an IP network, each host is configured with
its own IP Address and
a Gateway IP address = 192.10.25.1

QUICK START
1-6
1.3 How to Operate and Setup Intranet Applications
WAN
(Carrier)
EXIT VO/DA
ENTER
WANpro 2000
TAINET
WANpro 2000
LAN
LANT
LANR
RTS
CTS
TXD
RXD
LINK
CSR
CST
192.72.244.2192.72.244.1
WANpro 2000
#1
Host
Host
Host
Ethernet LAN
Host
Host
Host
Ethernet LAN
EXIT VO/DA
ENTER
WANpro2000
TAINET
WANpro 2000
LAN
LANT
LANR
RTS
CTS
TXD
RXD
LINK
CSR
CST
WANpro 2000
#2
Figure 1.4 The Intranet Connection over PPP
An Example of the Setup Procedures via front panel
1. WANpro 2000 #1 Setup
Step 1:Under LAN Setup menu:
IP Address = 192.72.244.1
Step 2:Under LAN Setup menu:
IP NetMask = 255.255.255.0
Step 3:Under WAN Setup menu:
WAN Protocol = PPP
Step 4:Under PPP Setup menu:
Local Address = 192.72.244.1
Step 5:Under PPP Setup menu:
IP NetMask = 255.255.255.255
Step 6: Under PPP Setup menu :
WAN Port Speed = Sync-External
Step 7:Under Routing Table menu:
Default Gateway = 192.72.243.1
Step 8:In an IP network, each host is configured with
its own IP Address and
a Gateway IP address = 192.72.244.1

QUICK START
1-7
2. WANpro 2000 #2 Setup
Step 1:Under LAN Setup menu:
IP Address = 192.72.243.1
Step 2:Under LAN Setup menu:
IP NetMask = 255.255.255.0
Step 3:Under WAN Setup menu:
WAN Protocol = PPP
Step 4:Under PPP Setup menu:
Local Address = 192.72.243.1
Step 5:Under PPP Setup menu:
IP NetMask = 255.255.255.255
Step 6:Under PPP Setup menu :
WAN Port Speed = Sync-External
Step 7:Under Routing Table menu:
Default Gateway = 192.72.244.1
Step 8:In an IP network, each host is configured with
Its own IP Address and
a Gateway IP address = 192.72.243.1
End of the Chapter

QUICK START
1-8

INTRODUCTION
2-1
CHAPTER 2
INTRODUCTION
Overview
2.1 Tainet’s WANpro 2000
2.1.1 Features
2.1.2 Specifications
2.2 Applications

INTRODUCTION
2-2
2.1 Tainet’s WANpro 2000
2.1.1 Features
lLCD display, provides instant information
lFront panel configuration, easy for use
lWAN port speed up to T1/E1
lProvides various DTE interface module
lProvides PPP & Frame Relay for high performance
Internet/Intranet access
lSupports RIP V1/V2, automatically create routing topology
lEmbedded SNMP agent
lProvides NAT (Network Address Translation) function, offer
simply firewall and provide IP applications
lProvides DHCP(Dynamic Host Configuration Protocol) server for
automatically assigning IP addresses & other configuration
information to hosts on a TCP/IP network
lProvides "In band" (TELNET) and "Out band" (Console port)
Management
lUse flash memory, provides an easy way to upgrade
lISDN interfaceàstill not available
lProvides hardware interface 1 WAN and 1 LAN (10 BaseT)
2.1.2 Specifications
Power
lAC: 90~265V (47~60Hz)
l5Watt
Dimensions
lPhysical Dimensions: 180mm x 48mm x 262mm (W, H, D)
lWeight: 0.9kg
lMounting: Desktop
Environment
lOperating Temperature: 0ºC to 50ºC
lRel. Humidity: 5% ~ 95%, non-condensing
LAN Interface
l10 Base-T auto detect
WAN Interface
lRS-232
Sync, Speed up to 128 Kbps
Aysnc, Speed up to 115200bps
lV.35 (Sync Speed up to 2Mbps)
lEIA-530 (Sync, Speed up to 2Mbps)