TaiShan TQ2001 User manual

Shandong Taishan Sports Equipment Co.,Ltd
Web : www.taishansports.cn
Installation Of Training Type Parallel Bar
TQ2001

Shandong Taishan Sports Equipment Co.,Ltd
Web : www.taishansports.cn

3
Shandong Taishan Sports Equipment Co.,Ltd
Web : www.taishansports.cn
Note
1) For gymnastic only, It should be used under the guidance and supervision of professionals
2) Childrenunder10yearsofagearenotallowedtouseit；
3) It shall not be used by more than one person at the same time, maximum load 500Kg;
4) For indoor use only
5) Please install and use special protective mat；
6) Before using, check all parts of the equipment with good condition, lock firmly, Replace
the parts in case of damage.
7) In case of abnormal sound and loose parts, stop using immediately；
8) No adjustment during use；
9) The bar cannot be excessive polished；
10)The surface of bar should be care and timely cleaning
11) Warm up before using the equipment,Stop using if you feel unwell
12) No knock and scratch with hard object
13) Wipe the surface of equipment with neutral detergent and clean water.

4
Shandong Taishan Sports Equipment Co.,Ltd
Web : www.taishansports.cn
Introduction
This training Type parallel bars can be used for competition and training. The height
adjusting tube with chrome-plated technology, wear-resistant, the installation is
convenient; The locking parts are clamped firmly and reliably, the bar is adjustable with
safety and stability
Product Parameter：
Dimensions：L 350cm×W 167cm×H（160cm-210cm adjustable）
Bar width adjustment42cm-62cm Stepless adjustable
Bar height adjustment :160cm-210cm, per 5c m adjustable
A Base B column C bar face D hexagon head bolt E plain washer F inner hexagon
head screw G pad H adjusting gasket

5
Shandong Taishan Sports Equipment Co.,Ltd
Web : www.taishansports.cn
Installation
Packing list：
A-Base 1 pc
B-column 4 pc
C-bar
2 pc
D-hexagon head
bolt 12 pcs
E-plain
washer
12 pcs
F-inner hexagon
head screw 4
pcs
G-pad 4
pcs
H-adjusting
gasket 8pc
I-24 single
ended wrench 1
pc
J-6mm internal
h- wrench
1 pc
K-3mm internal
h- wrench
1 pc
L-2.5mm internal
h- wrench
1 pc
M- PB adjustment
wrench
1 PC
Steps：
1) Place the base on a level, solid floor
2) as shown below，UseI-24 to fix A、B with D and E。
Note：The trademark column shall be located on the diagonal side;

6
Shandong Taishan Sports Equipment Co.,Ltd
Web : www.taishansports.cn
as shown below，fix C and B with H adjusting gasket、G pad and F inner hexagon head
screw 。
Note ：It is suggested to install one adjusting gasket on each column (in fact, each
column is equipped with 2 standard ones). After tightening the hexagon socket screw,
there is no obvious block during the adjustment of the spacing between the horizontal bar
and the column, and shaking the horizontal bar in the vertical direction ensures that there
is no obvious open movement between the horizontal bar and the column.In case of open
movement, remove the adjusting gasket.If the horizontal bar spacing adjustment has
obvious block, increase the adjustment gasket to 2 pieces。

7
Shandong Taishan Sports Equipment Co.,Ltd
Web : www.taishansports.cn
Introduction
Adjustment instruction：
As shown below, firstly，raise the handle of the lock gear component up (see the figure
below), and then adjust the tube inside to achieve the purpose of adjusting the height. At
the same time, rotate the lock gear component and the elbow to achieve width adjustment,
to ensure that the height of the four regulating tubes and the width between the two
horizontal bars are coordinated.
Maintenance：
1) It is necessary to check regularly whether all the connecting parts of the product are
loose or fall off, and tighten or replace them in time to ensure the safety of use。
2) When dirty on the surface of bar, gently wipe it with a towel to dip in clean water .
3) The equipment should be checked and maintained by professionals after 1 year
4) Apply lubricating oil to 1 Inner column and 3 locking pipe per month (see the picture
below), drag the shaft and 5 stud bolts to make the handle can turn flexibly and adjust
and lock the instrument, and it is strictly prohibited to apply lubricating oil to other
parts.
Note: special liquid lubricating oil should be used. Vegetable oil can be used instead if there is
no special lubricating

8
Shandong Taishan Sports Equipment Co.,Ltd
Web : www.taishansports.cn
5) When the lock parts loose (see chart following ), lift 1 handle, using L - Allen wrench will
have 4 socket head screw out on both ends, hold 1 handle, and then use 3 parallel bars card
head adjustment wrench by direction even shown below adjustment 2 sinistral lock nut, 5
right-lateral lock nut, lock lock parts, ensure the socket head cap screw on the lock nut
tightening up card slot and, finally will be resumed 1 handle in place

9
Shandong Taishan Sports Equipment Co.,Ltd
Web : www.taishansports.cn
Warranty
1) The warranty period from the date of delivery is shown in the
following table：
Item
Name
Warranty
Note
1
Base
3 Years
2
column
3 Years
3
Bar
1 year or 100000
frequency
4
foot
margin
1 year
5
Lock part
1 year
2) Damaged caused by improper use or maintain as required, User's responsibility
3) The surface damage of the equipment caused by scratches or bumps is not covered by
the warranty.
4) Provide free technical support and paid maintenance service for the equipment beyond the
warranty period.
Item
Name
Size
QTY
Note
1
single ended wrench
24
1
Tool
2
internal hex- wrench
6
1
3
internal hex- wrench
3
1
4
internal hex- wrench
2.5
1
5
PB adjustment wrench
1