TAKE-A-LABEL 250 User manual

Operating
Instructions
General Specications, Model 250
General Specications,
Model 250
Size (Approx.):
11.89W x 132.38H x 18.50D
Shipping Weight:
22 lbs (10 KG)
Electrical:
110/120VAC, 50/60HZ,
4 AMP FUSE
take-a-label.com • [email protected] • 16900 Power Dr., Nunica, MI 49448 • 616.837.9300
Note: e TAKE-A-LABEL dispenser is shipped
mounted to a base to prevent shiing in the container.
1. Remove the machine from the base.
**Always load the TAKE-A-LABEL dispenser with
the On-O switch in the (OFF) position.**
2. To load a roll of labels on the TAKE-A-LABEL,
loosen the unwind hub screw (57) on the unwind
collar (56) and remove the collar, unwind washer,
unwind spring, and disc from the unwind sha.
3. Place the roll of labels on the unwind sha between
the two unwind discs. Place the roll with the beginning
of the roll on the bottom with the web dispensing to
your right as you face the side of the machine.
4. Replace the unwind disc, unwind spring, and collar
onto unwind sha. If using labels on a 3” diameter
core, the hub on each disc will t inside the core
and support the roll of labels. If the labels are on a
1” core, simply slide the disc up snugly against the
roll of labels. When the disc is in place, tighten the
unwind hub screw against unwind sha.
5. read the loose end of the labels under and up the
front of the peel plate.
6. Pull the labels over the top of the peel plate far
enough to reach the waste take-up roll.
7. Remove the waste wind clip, thread the label backing
paper under the clip, and reinsert clip over loose paper.
8. Position the Photo Eye or Micro Switch Assembly by
loosening the wing nuts and moving assembly to the
right or le, so the sensor is at or near the center of
the labels. e Photoeye or Micro Switch Assembly
can be tilted forward or backward by loosening the
mounting bracket’s vertical adjustment wing nut.
9. Turn on the On-O switch. e waste wind sha
will turn, winding up the backing paper and dis-
pensing alabel at the top of the peel plate. When the
Photo Eye or Micro Switch senses the dispensed
portion of the label, the motor will stop. As each
label is removed, the machine will operate until the
next label is in position to be removed. (CAUTION:)
Turn o switch before removing wound up waste.
10. If the labels tend to follow the backing paper over
the top of the peel plate instead of peeling o,
then there is insucient tension on the web of the
labels. e shaadjustment collar should be moved
in to put more tension on the web.
11. If the motor stalls it may be necessary to move
the sha collar out to reduce the amount of
unwind tension.
Operating Instructions for the TAKE-A-LABEL Model TAL-250-18

1 25109, Unwind sha 1
2 25201, 250, 450, 750 Main frame 1
3 30653, 1/2”-13 BHCS 1
4 72618, Felt Brake Material 1
5 45136, Unwind Disk 2
6 25112, Unwind Washer 1
7 25113, Unwind Spring 1
8 26001, Unwind Collar 1
9 26002, Unwind Hub Screw 1
10 45181, Carriage Bolt 3
11 25213, Photo Eye Photo Eye Label Sensor 1
12 25204, Photo Eye Bracket Photo Eye Label Sensor 1
13 81904, Photo Eye Nut Photo Eye Label Sensor 2
14 25115, Waste Wind Clip 1
15 25114, Waste Wind Sha 1
16 45175, 10-32x3/8 BHCS 8
17 25116, 250 Peel Plate 1
18 70011, Optional Fan Fold Adapter Optional: Fan Fold Adapter 1
19 25127, 10-32x3/4” BHCS 4
20 45100, PCB - 250, 450, 750 DV Optional: Used with Special DC Photoeyes 1
21 76800, Heavy Duty Gear Motor 1
22 75835, Heavy Duty Fan Guard Optional: Heavy Duty Cooling Fan 1
23 75834, Heavy Duty Fan Option Optional: Heavy Duty Cooling Fan 1
24 30202, Cub 7 counter, DIN size Optional: Label Counter 1
25 25202, 250, 450, 750 Motor housing 1
26 Label, Company logo 1
27 40007, On/O Switch 1
28 25203, 250, 450, 750 Rear and side cover 1
29 45100, PCB - 250, 450, 750 DV 1
30 45102, PCB - 450, 750 CS 1
31 6-32x3/8” BHCS 2
32 45175, 10-32x3/8 BHCS 4
33 45120, ermo Label 1
34 81912, Small Cord Grip 1
35 25211, IEC Outlet, 701wx204 1
Not Shown 25212, IEC - US Line Cord 1
36 45182, Nylon Washer 4
37 45180, Wing Nut 5
38 25120, Micro Switch Mounting Bracket 1
39 45183, 10-32x1/2” BHCS 1
40 45181, Carriage Bolt 3
41 45307, Micro Switch Micro Switch-Style Label Sensor 1
42 45308, Trip Wire Micro Switch-Style Label Sensor 1
Not Shown 45409, Micro Switch Assembly Micro Switch-Style Label Sensor 1
43 45186, Cord Guide 1
COMMON PARTS FOR PRIOR MODEL YEARS
Not Shown 45208, Trip Wire 2014 and Older Models 1
Not Shown 45309, Switch Assembly 2016 and Older Models 1
Not Shown 81905, Photo Eye 2016 and Older Models 1
Not Shown 81906, Relay 2016 and Older Models 1
Not Shown 81907, Relay Socket 2016 and Older Models 1
Not Shown 25119, Lighted On/O Switch 2007 and Older Models 1
Not Shown 45217, Power Cord 2016 and Older Models 1
Not Shown 45153, Power Cord Clamp 2016 and Older Models 1
Not Shown 45155, Fuse Holder 2016 and Older Models 1
Not Shown 45157, Fuse 2016 and Older Models 1
TAL 250 Label Dispenser Exploded View ITEM# PART NUMBER NOTES QTY.
AND DESCRIPTION