TAKE-A-LABEL TAL-750HD User manual

PARTS LIST TAKE-A-LABEL Model TAL-750HD With Photo Cell
Part No. Item No. Description Part No. Item No. Description
1 25105 Housing 20 75803 Unwind Tension Knob
2 25106 Housing End Plt. 21 75804 Unwind Washer
3 25119 On/Off Switch 2007 & Older 22 75805 Unwind Grip Blade
3 40007 On/Off Switch 2008 & Newer 23 75807 Backing Plate
4 25120 Mico Swt. Mtg. Bkt. 24 75809 Bushings P77-9
5 25121 Nut .50 x 13 25 75808 Bushings P77-8
6 45152 Power Cord 26 75822 Unwind Spindle
7 45153 Power Cord Clamp (Not Sho
w
27 75812 Unwind Spring
8 45155 Fuse Holder 29 75817 Washer - Nylon
9 45182 Nylon Washer (Not Shown) 30 75806 Unwind Friction Washer
10 25122 Foot End Caps 31 76800 Gear Motor
11 81905 Photo Cell (Not Shown) 32 45157 Fuse 4 Amp. (Not Shown)
12 81906 Relay ( Not Shown) 33 45180 Nut Wing 1/4-20 (Not Shown)
13 81907 Relay Socket (Not Shown) 34 45181 Bolt Carriage 1/4-20 (Not Shown)
14 45210 Thumb Screws 35 45183 Button Head 10-32 Scr. (Not Shown)
15 72610 Waste Wind Clip 36 45184 Hex Nylon Nut 10-32 (Not Shown)
16 72612 Stripping Plate 38 75816 Locking Pin (Not Shown)
17 72613 Waste Wind Shaft
18 72615 Main Frame
19 75802 Unwind Shaft
16900 Power Drive * Nunica, MI 49448
Phone: [phone] * Fax: [phone]
Web Site: take-a-label.com
e-mail: [e-mail]

Operating Instructions for the TAKE-A-LABEL Model TAL-750HD
Note: The TAKE-A-LABEL dispenser is shipped mounted to a base to prevent shifting in the container.
Remove the machine from the base.
Always load the TAKE-A-LABEL dispenser with the On-Off Switch (3) in the (OFF) position.
1 To load a roll of labels on the TAKE-A-LABEL, slide the roll of labels over the spinndle (26) using the
blade (22) to grip the core of the roll of labels.
2 Place a roll of labels on the unwind shaft so that the beginning of the roll is on the bottom of the
web coming off to your right as you face the side of the machine.
3 Thread loose end of labels under and up the front of the stripping plate (16).
4 Pull labels over top of stripping plate far enough to reach the waist take-up roll (17).
5 Remove the waist wind clip (15), thread label backing paper under clip, and reinsert clip over loose paper.
6 Position the photo cell switch by loosening thumb screws (32) and moving the assembly to right or left so
that the photo cell is at or near the center of the labels. The photo cell switch can be tilted forward
or backward by loosening the mounting bracket vertical adjustment wing nut (27).
7 Turn on On-Off switch (3). The waist wind shaft (17) will turn, winding up backing paper and exposing a
label at the top of the stripping plate. When the photo cell sees the dispensed portion of the label,
the motor will stop. As each label is removed, the machine will operate until the next lable is in position to
be removed. (CAUTION:) Turn off switch (3) before removing wound up waist.
8 If labels tend to follow backing paper over the top of the stripping plate instead of peeling off,
there is probably insufficient tension on the web of the labels. The unwind tension
adjustment knob (20) should be turned in to put more tension on the web.
9 If the motor stalls it may be necessary to reduce the tension. Turn the Tension Knob (20) out to reduce the
amount of unwind tension.
16900 Power Drive * Nunica, MI 49448
Phone: [phone] * Fax: [phone]
Web Site: take-a-label.com
e-mail: [e-mail]