TANDELTA SENSE-3 User manual

WHAT’S IN THE BOX?
1. CONFIGURE
2. INSTALL AND CONNECT
www.tandeltasystems.com
[email protected]
Copyright © Tan Delta Systems Ltd.
OQSx-G2
Cable J
Sensor & Cable J available separately as SENSE-1 Kit
Product
USB
LAN
Port
USB
Port
Micro
SIM
LED 2
LED 3
LED 4 LED 1
S1 S2 S3
Gateway
Power
66 19
6x Ø6.5
165
Cable HP Cable GH
HCP-1
Cable SH
OQSx-G2
SENSE-3 Unit
Best practice is to configure all cables
before powering on the system.
1. Install all sensors to their intended assets.
2. Mount the SENSE-3 unit to a wall or rigid
surface using any 4 of the 6x Ø6.5 clearance
holes. Ensure IP67 cover is attached.
3. Check Cable GH has been preconnected when
shipped. If not, connect it as shown.
4. Route all Cable SHs from sensors to slots
S1/S2/S3.
5. Populate any unused slots with Continuity
Plugs (HCP-1).
6. If using a 4G SIM, attach the antennas
to the Gateway.
7. Connect Cable HP and apply power
(9-30VDC).
8. Check data is coming through on
TD Online for each sensor.
9. See Master User Guide for
troubleshooting help.
GATEWAY KIT
I
SENSE-3
QUICK START GUIDE
1. Allow Configuration Cable to install and update drivers.
2. Install CADS from USB or by scanning the QR code or
go to: www.tandeltasystems.com/support/
3. Select the Modbus RTU over RS485 comms protocol.
4. Set unique Node ID from 1-16 for each sensor.
5. Ensure 9.6000 Kbps Bit Rate is selected.
6. Select desired oil for each sensor.
7. Configure Gateway network for 4G SIM, WiFi,
or Ethernet using the Gateway Configuration Tool on
the USB. Save “.conf” configuration file.
8. Connect Cable HP to Gateway Hub. LED 3 will have
a steady green light.
9. Insert USB into Gateway. LED 2 will turn red for
a few seconds, then all LEDs will go off. Remove USB
at this point.
10. After 1 minute, the Gateway will reboot. LED 3 will
have a steady green light. LED 4 will have a steady
amber light once the Gateway has connected
successfully to TD Online.
SCAN ME
SENSE-3 Unit (Gateway pre-assembled
with Gateway Hub and Mounting Kit)
Quick Start
Guide
USB Stick containing
• Gateway Configurator
• Software
• CADS
• Master User Guide
Gateway Hub to Gateway Cable 0.2m
(Cable GH)
Gateway 4G Antenna
Cable
2x Gateway Hub Continuity Plug
(HCP-1)
Gateway Hub Power Cable 10m
(Cable HP)

GATEWAY KIT
I
SENSE-3
QUICK START GUIDE
www.tandeltasystems.com
[email protected]
Copyright © Tan Delta Systems Ltd.
You can find further information in the Master User Guide on the support page of our
website. If you have any further questions, please contact our support team by email:
[email protected] who will answer no later than the next working day.
Alternatively, refer to Master User Guide
available at: www.tandeltasystems.com/support
SCAN ME
Page 2 of 2
SUPPORT – FAQ
If you have any issues, please read the tips below before contacting us for further support.
1. Why is the Ring LED not illuminating?
Check all slots are populated with either Cable SH or Continuity Plugs (HCP-1).
2. Why is the Data LED not flashing?
The Data LED should flash once per sensor connected in a 15-second period. If not flashing, check the sensor configuration using CADS.
Should be Modbus RTU over RS485, bit rate 9.600Kbps, and a unique Node ID (1-16) per sensor.
3. I’ve configured the Gateway for a 4G SIM, why is LED 4 not illuminating amber?
Check the antennas are connected to the Gateway and you are in an area with 4G signal.This can be done by inserting the SIM into
a 4G-enabled phone and checking signal strength.
4. I’ve configured the Gateway for WiFi or ethernet, why is LED 4 not illuminating amber?
Recreate the “oqgateway.conf” file using the Gateway Configurator Tool supplied on the USB. Double-check all credentials, save the file,
and reconfigure the Gateway.
5. The Gateway does not reboot when I insert a USB with a new “oqgateway.conf” file. Why?
The Gateway’s configuration is identical to the configuration file you are atempting to load onto the device.The Gateway will only reboot
if the configuration file is different in some way to the Gateway’s existing configuration.