TBK vision TBK-6006DNHV User manual

Vari-Focal IR Camera
Instruction Manual
VER.:1.0, NO.:040156

1
Thank you very much for purchasing our product. Before operating this
product, please read this instruction manual carefully to ensure proper use.
1. Safety Precautious
CAUTION
RISK OF ELECTRIC
SHOCK. DO NOT OPEN!
CAUTION : TO REDUCE THE RISK OF ELECTRIC
A
L SHOCK, DO NOT OPEN CO
V
ERS.
NO USER SER
V
ICE
A
BLE P
A
RTS INSIDE. REFER SER
V
ICING TO QU
A
LIFIED
SER
V
ICE PERSONNEL.
Disposal of Old Electrical & Electronic Equipment (Applicable in
the European Union and other European countries with separate
collection systems).
Please be extra careful not to shake the camera
Please avoid places where there is direct sunlight
When using this camera in places where the lighting differs greatly,
please use the auto iris lens with ND filter.
Please avoid places where temperatures exceed 50℃or more,
high humidity or where direct rain drops hit, frequent vibrations, or
shocks occur.
During the night, if a minimum brightness of 0.1 Lux can not be
achieved, install appropriate light fixtures.
When the camera is not used, keep the lens or the lens cap
attached to protect the sensor.
2. Description
The camera uses SONY high sensitive super HAD interline transfer
image sensor, and employs digital signal processor (DSP) chip-set for
image control, and all integrated state circuitry which provide
extremely long life and high reliability. This camera offers excellent
image quality with low lag and high burn resistance, and is not subject
to distortions from magnetic fields.
Highly resistance to shock and vibration, easy to install, this
camera is a very good choice for your color CCTV system.

2
3. Feature
Camera with 1/3“ SONY Super HAD CCD sensor in metal case.
Employs Digital Signal Processor (DSP) chip-set for image
control.
Pixel number: NTSC=380K/ PAL=440K for high resolution models, and
NTSC=270K/ PAL=320K for normal resolution models.
High sensitivity, low smear, high anti-blooming, and high S/N ratio.
Powerful functions: Auto Electronic Shutter (AES), Auto Iris (AI),
Auto Gain Control (AGC), Auto White Balance (AWB), and Back
Light Compensation (BLC).
Built-in anti-aliasing and IR-cut optical filter.
Cds auto switching IR-LED control.
4. Contents
Item Name of Part Quantity
1 Camera 1
2 Appurtenance Bag 1
3 Screws 2
4 Mounting Block 1
5 Instruction Manual 1

3
5. Name of Each Part
Mounting Bracket 7
Focal
6
Adujustment
WIDE
TELE 5
Cover 4
Audio (optional)
LED (optional)
Far
Near
Fig. 1

4
1Output
Power In
2
3LED
Indicator
-
10
Video
Audio Output
BLC:Back Light Compensation ON/OFF
AGC:Auto Gain Control High/Low
FL:Flicker Less ON/OFF
AES:Auto Electronic Shutter ON/OFF
8
9
VR Adjustment level
for DC Drive Lens
(optional)
Video
1
AGC:Auto Gain Control High/Low
AES:Auto Electronic Shutter ON/OFF
BLC:Back Light Compensation ON/OFF
Power In
2
3LED
Indicator
Output
FL:Flicker Less ON/OFF
-8
9
VR Adjustment level
for DC Drive Lens
Audio Output
10 (optional)
Fig. 2
Fig. 3

5
6. Installation & Operation
Please refer to Fig. 1 or Fig. 2 (P3 & P4) and setup guide below:
1. Connect the video output (1) to the monitor or other video device
through a 75 Ohms type coaxial cable.
2. Connect the power source (2), AC with the power cord, or DC by
using the DC Jack (+12V DC is in the center of the jack plug),
then the LED indicator will lit.
3. Once the picture appears on the monitor, open the cover (4) adjust
the lens wrench of “WIDE←→TELE” (5) to get the view angle that
you desire, then adjust the focus wrench (6) of the lens to obtain the
best picture.
4. Tighten the two wrench (5) and (6), then put the cover (4) back.
5. Mount the mounting bracket to hole (7) on the top or bottom of the
camera, using the enclosed 8mm mounting block with 2 screws
furnished.
6. DIP Switch (8) Setting
•BLC FUNCTION
Set Switch-OFF/ BLC to BLC to enable Back Light Compensation
(BLC) function.
•AUTO IRIS FUNCTION
When using an Auto Iris Lens, the Switch-AES/ OFF should be
set to OFF, to disable the AES function. Adjust the VR LEVEL (9)
to the proper level.
•AGC-Hi / AGC-Lo Function
This switch setting to High or Low of the AGC maximum gain.
•Flickerless Function
Set switch-OFF/FLON to FLON to enable flickerless function, in
this mode, the switch-AES/OFF is auto disabled.
•AES Function
When using the lens (other than Auto Iris Lens), the Switch-AES/
OFF should be set to AES.

6
7. Specification
According to the camera purchased, select and refer to the appropriate specification below:
Note: Design and specifications are subject to change without prior notice.
Color Camera
Image Device 1/3” Color SONY
Super HAD
1/3” Color SONY
Hi-Res. Super HAD
1/3” Color SONY
Ex-View HAD
1/3” Color SONY
Hi-Res. Ex-View HAD
Picture Elements NTSC:510*492
PAL:500*582
NTSC:768*494
PAL:752*582
NTSC:510*492
PAL:500*582
NTSC:768*494
PAL:752*582
Resolution 380 TVL 470 TVL 380 TVL 470 TVL
Min. Illumination 0.2 Lux / F2.0 0.3 Lux / F2.0 0.05 Lux / F2.0 0.15 Lux / F2.0
S/N Ratio More than 48 dB
Electronic Shutter NTSC:1/60s~1/100,000s, PAL:1/50s~1/110,000s
Flickerless Mode On/ Off (NTSC:1/100s, PAL:1/120s)
Gamma 0.45
Iris Control DC Drive
Lens Furnished
Vari-Focal: f3.7~12.0mm/ F1.6~360 (Wide:H71.6°×V23.8°, Tele:H55.8°×V17.9°)
Vari-Focal: f3.7~12.0mm (ICR)/ F1.6~360 (Wide:H71.6°×V23.8°, Tele:H55.8°×V17.9°)
Vari-Focal: f4.0~9.0mm/ F1.6~360 (Wide:H68.0°×V50.2°, Tele:H32.1°×V24.1°)
Vari-Focal: f9.0~22.0mm/ F1.6~360 (Wide:H29.2°×V13.0°, Tele:H21.7°×V9.7°)
ICR Function Auto (optional)
Gain Control High / Low
White Balance Auto
Back Light Comp. ON/OFF
Sync. System Internal
Video Output 1 Vp-p / 75 Ohms.
Audio Output 2 Vp-p / 50 Ohms. (optional)
Power Supply DC12V ±10％, AC24V, AC100~240V (optional)
Power
Consumption
IR OFF DC/ 170mA max., AC/ 2.5 W max.
IR ON DC/ 280mA max., AC/ 3.8 W max.
Operating Temp. -10℃to 50℃(14℉to 122℉)
Infrared Illuminator Module
Wavelength 850nm
Illuminate Distance 10M