TCL L32F3300 User manual

L32F3300
7&/
6(59,&(0$18$/
















-MT10B-LA


&DXWLRQĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂ
6SHFLILFDWLRQ ĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂ
%ORFN'LDJUDP
$OLJQPHQW3URFHGXUHĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂ
6FKHPH'LDJUDPĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂĂ
3&%/$<287
7URXEOHVKRRWLQJ




7KLVPDQXDOLVWKHOD WHVWD WWKH WLPHRIS ULQWLQJDQ GGRHVQRW
LQFOXGHWKHPRGLILFDWLRQZKLFKPD\EHPDGHDIWHU WKHSULQWLQJE\
WKHFRQVWDQWLPSURYHPHQWRISURGXFW

CA UTION: TO RE DUCE THE RIS K OF
ELECTR ICA L SHOCK, DO NOT RE MOVE
COVER (OR BACK). NO USER SERVICEABLE
PAR TS INS IDE . RE FER SE R VIC ING TO
QUALIFIE D SERVICE PERSONNEL.
The lighting flash with arrowhead symbol, with an equilateral triangle is intended to
alert the user to the presence of uninsulated voltage within the products
enclosure that may be of sufficient magnitude to constitute a risk of electric shock to
the person.
The exclamation point within an equilateral triangle is intended to alert the user to the
presence of important operating and maintenance (servicing) instructions in the
literature accompanying the appliance.
CAUTION:
Use of controls, adjustments or procedures other than those specified herein may result in
hazardous radiation exposure.
CA U T ION
RISK
RISK OF
ELECTR I
ELECTR IC
SHOCK
SHOCK DO
NOT
NOT
OPEN.
OPEN.
2
dangerous
WARNING: TO REDUCE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT
EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
SCHNEIDER ELECTRONICS GMBH-GERMANY
1. CAUTION
2

1. When the power cord or plug is damaged or frayed, unplug this television set from the wall outlet and refer servicing to
qualified service personnel.
2. Do not overload wall outlets and extension cords as this can result in fire or electric shock.
3. Do not allow anything to rest on or roll over the power cord, and do not place the TV where power cord is subject to
traffic or abuse. This may result in a shock or fire hazard.
4. Do not attempt to service this television set yourself as opening or removing covers may expose you to dangerous
voltage or other hazards. Refer all servicing to qualified service personnel.
5. Never push objects of any kind into this television set through cabinet slots as they may touch dangerous voltage
points or short out parts that could result in a fire or electric shock. Never spill liquid of any kind on the television set.
6. If the television set has been dropped or the cabinet has been damaged, unplug this television set from the wall outlet
and refer servicing to qualified service personnel.
7. If liquid has been spilled into the television set, unplug this television set from the wall outlet and refer servicing to
qualified service personnel.
8. Do not subject your television set to impact of any kind. Be particularly careful not to damage the picture tube surface.
9. Unplug this television set from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a
damp cloth for cleaning.
10.1. Do not place this television set on an unstable cart, stand, or table. The television set may fall, causing serious injury
to a child or an adult, and serious damage to the appliance. Use only with a cart or stand recommended by the
manufacturer, or sold with the television set. Wall or shelf mounting should follow the manufacturer s instructions, and
should use a mounting kit approved by the manufacturer.
10.2. An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces
may cause the appliance and cart combination to overturn.
CAUTION:
Read all of these instructions. Sa ve these instructions for later use . Follo w all W arnings and
Instructions marked on the audio equipment.
1. Read Instructions-All the safety and operating instructionsshouldbe read before the productis operated.
2. Retain Instructions- The safety and operating instructions should be retained for future reference.
3. Heed Warnings- All warnings on the product and in the operating instructions should be adhered to.
4. Follow Instructions- All operating and use instructions should be followed.
3
SCHNEIDER ELECTRONICS GMBH-GERMANY
IMPORTANT SAFETY INSTRUCTIONS
FOR YOUR PERSONAL SAFETY
3

11. Do not use this television set near water ... for example, near a bathtub, washbowl, kitchen sink, or laundry tub, in a
wet basement, or near a swimming pool, etc.
Never expose the set to rain or water. If the set has been exposed to rain or water, unplug the set from the wall
outlet and refer servicing to qualified service personnel.
12. Choose a place where light (artificial or sunlight) does not shine directly on the screen.
13. Avoid dusty places, since piling up of dust inside TV chassis may cause failure of the set when high humidity persists.
14. The set has slots, or openings in the cabinet for ventilation purposes, to provide reliable operation of the receiver, to
protect it from overheating. These openings must not be blocked or covered.
Never cover the slots or openings with cloth or other material.
Never block the bottom ventilation slots of the set by placing it on a bed, sofa, rug, etc.
Never place the set near or over a radiator or heat register.
Never place the set in enclosure, unless proper ventilation is provided.
15.1. If an outside antenna is connected to the television set, be sure the antenna system is grounded so as to provide some
protection against voltage surges and built up static charges, Section 810 of the National Electrical Code, NFPA No.
70-1975, provides information with respect to proper grounding of the mast and supporting structure, grounding of the
lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection
to grounding electrode, and requirements for the grounding electrode.
15.2. Note to CATV system installer : (Only for the television set with CATV reception)
This reminder is provided to call the CATV system attention to Article 820-40 of the NEC that provides
guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding
system of the building, as close to the point of cable entry as practical.
16. An outside antenna system should not be located in the vicinity of overhead power lines or other electric lights or power
circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care
should be taken to keep from touching such power lines or circuits as contact with them might be fatal.
17. For added protection for this television set during a lightning storm, or when it is left unattended and unused for long
periods of time, unplug it from the wall outlet and disconnect the antenna. This will prevent damage due to lightning
and power-line surges.
ANTENNA
LEAD- IN WIRE
ANTENNA DISCHARGE
UNIT (NEC SECTION
810-20)
GROUNDING
CONDUCTORS
(NEC SECTION810-21)
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250. PART H)
ELECTRIC SERVICE
EQUIPMENT
GROUND CLAMP
NEC-NATIONAL ELECTRICAL CODE
EXAMPLE OF ANTENNA GROUNDING AS PER
NATIONAL ELECTRICAL CODE
EXAMPLE OF ANTENNA GROUNDING AS PER NATIONAL ELECTRICAL CODE INSTRUCTIONS
a built-in
installer s
4
SCHNEIDER ELECTRONICS GMBH-GERMANY
PROTECTION AND LOCATION OF YOUR SET
PROTECTION AND LOCATION OF YOUR SET
4

18. This television set should be operated only from the type of power source indicated on the marking label.If you are not
sure of the type of power supply at your home, consult your television dealer or local power company. For television
sets designed to operate from battery power, refer to the operating instructions.
19. If the television set does not operate normally by following the operating instructions, unplug this television set from the
wall outlet and refer servicing to qualified service personnel. Adjust only those controls that are covered in the operating
instructions as improper adjustment of other controls may result in damage and will often require extensive work by a
qualified technician to restore the television set to normal operation.
20. When going on a holiday : If your television set is to remain unused for a period of time, for instance, when you go on
a holiday, turn the television set and unplug the television set from the wall outlet.
21. If you are unable to restorenormal operation by following the detailedprocedurein your operatinginstructions,
do not attempt any further adjustment. Unplug the set and call your dealer or service technician.
22. Whenever the television set is damaged or fails, or a distinct change in performance indicates a need for
service, unplug the set and have it checked by a professional service technician.
23. It is normal for some TV sets to make occasional snapping or popping sounds, particularly when being
turned on or off. If the snapping or popping is continuous or frequent, unplug the set and consult your
dealer or service technician.
24. Do not use attachments not recommendedby the television set manufacturer as they may cause hazards.
25. When replacement parts are required, be sure the service technicianhas used replacementparts specified
by the manufacturer that have the same characteristics as the original part. Unauthorized substitutions
may result in fire, electric shock, or other hazards.
26. Upon completion of any service or repairs to the television set, ask the service technician to perform
routine safety checks to determine that the television is in safe operating condition.
off
5
SCHNEIDER ELECTRONICS GMBH-GERMANY
OPERATION OF YOUR SET
IF THE SET DOES NOT OPERATE PROPERLY
FOR SERVICE AND MODIFICATION
5

EM BUSINESS CENTER
FTV PRODUCT PLANNING DEPT.
SPECIFICATION RELEASE
Version: V0.1 Issued Date: 2012.03.26
PICTURE
Panel Size (inch)
32'
Category
LCD TV(LED BACK LIGHT)
Aspect Ratio
16:9
Color Temperature
Warm / Standard / Cold SIGNAL FORMAT CAPABILITY
Backlight Adjustable
Yes Component Video Format Y,Pb/Cb,Pr/Cr:up to 720p,1080i,1080p @50Hz/60Hz
Scaler Mode Auto, Full Screen, Normal, Zoom DVI Video Format Up to XGA for HDMI-PC
Picture Effect
User，Cinema，Sport，Vivid，Hi-Bright HDMI Video Format Up to 720p,1080i,1080P
Film Mode (3:2 pull down)
Yes PC Compatibility VGA: up to UXGA@60Hz
Picture Enhancement TERMINALS
Comb Filter
3D Audio/CVBS Input (Composite) 2 R/L+2 Video: AV1, AV2(Bottom)
Core Technology
High-quality scaling engine & 3-D video de-interlacer YPbPr Input 1
CCS
-- Audio Input for YPbPr 1
MDDiTM yes YCbCr Input Share with "YPbPr"
Blue Stretch
-- Audio Input for YCbCr Share with Audio for "YPbPr"
Black Stretch
yes VGA Input(RGB) 1 (D-Sub,15 Pins)
Motion Compensation
yes Audio Input for RGB 1
DLTI
yes DVI share with “HDMI” port
DCTI
yes Audio Input for DVI Share with Audio for "VGA"
Dynamic Skin Correction
yes HDMI 1.3+CEC 3
DNR
yes Audio/CVBS Output (Composite) 1 (R/L+CVBS)
Panel Specification SPDIF 1 (optical)
Panel supplier CSOT ST3151A04-1 OPENCELL RF Input 2 (Antenna, Cable)
Viewing Technology
-- USB 2.0 2
Display Resolution
1366*768 Basic Info.
Brightness (cd/m2)
400 TV System ATV:NTSC PAL/M PAL/N DTV:ISDB-T
Contrast Ratio
4000:1 AV System PAL,NTSC
Response Time
6.5ms (G to G) TV Channels (Analog) Cable (1～125), Antenna (2～69)
Viewing Angle (H/V)
178°/178° TV Channels (Digital) Antenna (7～69)
Life Time
30,000hrs (min) Chassis MT5310B-LA
Color 16.7M (8 bit) Certification CB
SOUND Power Supply AC 100V-240V 50/60Hz
Speakers
Integrated speakers (Bottom side) Power Consumption-TV on 70W
Audio Power Output
5W*2 Power Consumption-Standby Less than 0.3W
Sound Processing BTSC (SAP, Stereo, Mono) Default Color of Front Cabinet BLACK
DVSS (Dolby Virtual Surround)
-- Keyboard Position Side
DDAS (Digital Dynimic Audio System) -- Base Stand Detachable Yes
AVC (Auto Volume Control)
Yes Unpackaged Dimension for Main Body (L*H*D) (mm)
BBE
-- With Base Stand (mm) 734*488*183
SRS
-- Without Base Stand (mm) 734*441*69
Packaged Dimension (L*H*D)
Main Body (mm) 852*191*559
Speaker Box --
Base Stand …
Function Net Weight (Kg) 8.5kg
V-Chip
-- Gross Weight (Kg) 10.5kg
subtitle
yes Container Loading
Teletext
yes 20 feet 320
PIP/POP
-- 40 feet 672
Macro Vision
-- 40 feet high 782
Calendar
-- ACCESSORIES
Clock/Timers
Yes Operation Manual English(Default)
Lock Yes Remote Control For TV control (with two batteries)
OSD Language English/Spanish/Portuguese Base Stand Packaged with Main Body
OSD Features
Semi-transparent Speaker Box Integrated
Card Reader
-- Wall Mount WMB231,100×100×M4
HDMI CEC
Yes Others AC Power cord,AV/CMP Adapter cable
USB Connection
Yes
Game
--
Screen Saver
--
hotel
yes
Demo Function
--
Picture Freeze
yes
Natural light yes
Design and specifications are subject to change without notice! Page 1 of 1
Approved by:
MTS, AVC, Equalizer, Surround
Sound Control
Model: L32F3300/MT10B-LA/CSTM E18V1
Sound Features
Drafted by:卓建寿
Volume, Balance, Bass Boost

IF+/-
IF+/-
CEC
IF+/-
Serial TS in
DIM
Power su
pp
l
y
MT5310
ADC
HDMI RECEIVER
CVBS DECODER
3D COMB FILTER
MPEG4 DECODER
SCALER
HDMI1
HDMI2
HDMI3
HDMI 1.3
SWITCH
˄3 IN 1˅
TMDS
I/F
VGA In
ISDB-T
Tuner
AV 1 I n
Spdif
Out
YPbPr
In
Head
p
hone
USB2
USB1
Audio
In
LVDS
DDR3
DDR3
JTA
G
T90517
DEMO
IP/GPIO
FLASH
AUDIO
AMP
USB
Audio
In
4052
IR
KEY
Panel
I/F
LV
DS
DDR3
Nor
Flash
64Mbit
Audio Amp.
AV 2 I nAV O U T

Factory Alignment Specification of normal SIACP
Page 1 of 12
TCL WW R&D
FPD CENTER
Factory Alignment Specification of normal SIACP
For MT10-LA
Version 1.0
PREPARED BY : ∳䰇 DATE : 2011-4-22
APPROVEDBY: DATE:

Factory Alignment Specification of normal SIACP
Page 2 of 12
TableofContents
Feature Specification ........................................................................................................................................... 4
INFO.................................................................................................................................................................... 5
1.Electrical Assembly Alignment ........................................................................................................................ 5
1.1 Preconditions – DC/DC Check...................................................................................................................... 5
1.2 SW download ................................................................................................................................................ 5
1.3 Panel ID check and modify ........................................................................................................................... 6
1.4 Functional Test .............................................................................................................................................. 6
1.5 DDC & EDID Test......................................................................................................................................... 6
1.6 HDCP Test ..................................................................................................................................................... 7
2.Final Assembly Alignment ............................................................................................................................... 7
2.1 FactoryMenu.................................................................................................................................................. 7
2.2 Entering to “P” Mode .................................................................................................................................... 7
2.3 White Balance Alignment.............................................................................................................................. 7
2.4 High Pot. and Insulating Resistance Tests ..................................................................................................... 8
3.Factory default settings..................................................................................................................................... 8
Appendix
n
“How to download FLASH SW”................................................................................................ 11
Appendix
o
“How to upgrade FLASH SW from USB”.................................................................................... 11
Appendix
p
“Modify panel ID with RC” ......................................................................................................... 12

Factory Alignment Specification of normal SIACP
Page 3 of 12
Disclosure
The information contained in this document is proprietary to TCL SZ FPD lab and shall not be
disclosed by the recipient to third persons without the written permission of the team leader or
GM of R&D.
Revision History
Status, Ver Date, Drafter Description of changes
V1.0 2011-4-22 This is the draft version of normal SIACP
gHDMI as the main absolute input
gThe password of factory menu is 9735
gUse RC to change project ID
gWhite Balance

Factory Alignment Specification of normal SIACP
Page 4 of 12
FeatureSpecification
These chassises are designed for South America LCD TV. The main chip is from Mediatec
(MT5310 series) and supports below inputs and outputs:
class item Status MT10B-LA MT10L-LA
ATV
( PAL- M/N, NTSC-M)
¥Cable&Antenna Cable&Antenna
DTV
(SBTVD-T)
¥Antenna Antenna
HDMI
(480i/p, 576i/p, 720p up to
1080i/p, compliant v1.2. with
HDCP)
3 P300
P301
P302
P301
P302
P303
VGA 1 P406 P406
VGA/DVI audio 1 P400 P400
CMP
(YPrPb can support from 480i
up to 1080p,audio)
1P1
P455 (Audio)
P404
Side AV or back AV
(CVBS,audio)
2 P304
P404
P423
P421
USB player
(picture,video,audio)
2 P303
P401
P401
P427
Headphone output ¥P800 P800
SPDIF output Optical P405 P405
AV out 1 P498 P407
P424
P425
Input
&
Output
function
Others
VGA connector of MT5310B definition:
VGA: Pin4:RXD VGA Pin11:TXD


Factory Alignment Specification of normal SIACP
Page 5 of 12

INFO
ªAll tests and measurements mentioned hereafter have to be carried out at a normal mains voltage
(220 ~ 240 VAC)
ªAll voltages have to be measured with respect to ground, unless otherwise stated
ªAll final tests have to be done on a complete set including LCD panel in a room with temperature of
25+/-7°C
ªThe White Balance (color temperature) has to be performed into subdued lighted room after at
least 1 hour of warm-up/burn-in. This is applicable for both Alignment and Picture Performance
evaluation at OQA in order to be set free of any temperature drift ( colorimetry vs time)
1.ElectricalAssemblyAlignment
1.1 Preconditions – DC/DC Check
Before power on, please check the board according to the relevant block diagram and circuit
diagram, and make sure that no serious error should destroy the board. For example,the output
of DC/DC and LDO should not shorted to ground.
Supply a suited voltage and power on , then check the voltage according to the relevant
block diagram , circuit diagram and voltage spec . the error should less than 5% .For example,
the voltage for main chip(DV33, AV33, VCCK,etc.), the voltage for DDR (DDRV) , the voltage for
amplifier(AUDIO_PWR),etc. Only the standby voltage is necessary if there is no software in the
flash .
Position Value Remarks
R111 3.3V +/-5% +3V3SB
C117 (positive pin) 5.0V +/-5% +5V
C101 (positive pin) 1.1V +/-5% Vcck
U105 1.2V +/-5% AVDD1V2
U104 3.3V +/-5% DVDD3V3
U109 3.3V +/-5% A VDD3V3
U12 1.5V +/-5% DDRV
C100 (positive pin) 12V +/-5% +12V
U102 5.0V +/-5% TUNER_VCC
Note: Different model may have different configuration of DC/DC circuit.
1.2 SW download
Download the latest release MT10_SW into the flash using MTK SW tool. See Appendix
n
“How to download FLASH SW”. Or upgrade the SW from USB port See Appendixo“How to

Factory Alignment Specification of normal SIACP
Page 6 of 12
upgrade FLASH SW from USB”.
Remenber to do “Reset all” after upgrade the SW.
1.3 Project ID check and modify
There is different ID stored in the NVM depended on different Panels. Modify it with Hyper
terminal if the initial ID or a wrong ID make the set can not display clearly. See Appendix
p
. It can
be checked and modified in Factory menu->Project info->Project ID if the set can display
clearly . The set should be restart if the project ID is changed .
1.4 Functional Test
Once the boards (chassis, KB, IR, PSU…) and the panel are well interconnected, connect all
external generator devices to relevant inputs/outputs below according to their respective test
patterns format and check picture content and sound quality accordingly:
Source Test signal (generator) Test pattern (format/image)
Analog /Digital Tuner RF cable Full Band (VHF/UHF) + CATV
SBTVD-T
Composite(CVBS) Chroma/Fluke PAL Half Color & Gray bars
VGA Chroma/QuantumData 1024x768@60Hz
Half Color & Gray bars
CMP (YPrPb) Chroma/QuantumData 1080i@60Hz
Half Color & Gray bars
HDMI DVD with HDMI compliancy Movie 720p@60Hz
Headphone RF cable First channel
Loud Speakers RF cable First channel
USB USB device Picture musica Video
Audio tones can be defined by the factory (ie: 1KHz & 3KHz, sweep, …).
Picture video formats can be changed by the factory according to their own standard.
1.5 DDC & EDID Test
The E-EDID data structure are according to VESA Enhanced EDID 1.3 (and EIA/CEA-861B for
HDMI).
HDMI have their own separate bin files:
For EDID check, it’s needed to check whether the correct EDID is downloaded by checking
corresponding EDID NVM Checksum or read them out to check bit by bit if it is in line with the
released EDID bin file.

Factory Alignment Specification of normal SIACP
Page 7 of 12
1.6 HDCP Test
For HDCP compliancy, it’s needed to check whether the HDCP key has been well set.
2.FinalAssemblyAlignment
2.1 FactoryMenu
Follow the below steps to pop-up the Factory Menu in case of “FactoryKey” is disable:
-press RemoteControl key “MENU” to display main menu
- Select “Picture” and press “OK” key to enter the picture submenu
- Select “Contrast” item
-press the subsequence RemoteControl keys “9”, “7”, “3” and “5”
Press RemoteControl key “Return” To pop-up the Factory Menu in case of “FactoryKey” is
enable.
The status of “Factory Key” can be changed in Factory Menu->Hotkey
Press RemoteControl “OK” key or “RIGHT” key to enter the submenu.
Press RemoteControl “Menu” key to go back to the root menu.
Press RemoteControl “RIGHT”or “LEFT” key to change the values.
Press RemoteControl “OK” key run the function.
Press RemoteControl “Exit” key exit the factorymenu.
2.2 Entering to “P” Mode
Turned on the factory key to enter into “P” mode.The TV will display the following info in
bottom left corner in “P” mode.
-main version ***
-project ID ***
-P/PS/D ***
2.3 White Balance Alignment
Make sure that the picture mode is “vivid”, enter to “P” mode(turned on the factory key) and
switch off “Pic. Enhance” in Factory Menu-> White Balance before white balance alignment .
VGA,CMP,DTV,CVBS_PAL Color Coordinates are relative to HDMI.
CVBS_SECAM and CVBS_NTSC Color Coordinates are relative to CVBS_PAL.
Warm and Cool Color Coordinates are relatives to Normal mode.
Only HDMI(YUV 720p@60Hz) input requires color temperature adjustment. All the Relative
Matrix Offsets should be set while doing alignment.

Factory Alignment Specification of normal SIACP
Page 8 of 12
Each panel has it’s own colour coordinates, Please refer to the following table.
㪛㫐㫅㪸㫄㫀㪺㪆㪎㪇㩼㩷㪮 L32V6200/L32E5200 L42E5200F/L42V6200F C32E320/L32P60 C42E320F/L42P60F
xyxyxyxy
Normal 0.275 0.310 0.275 0.290 0.280 0.290 0.280 0.290
Cool 0.265 0.285 0.265 0.290 0.270 0.280 0.270 0.280
Warm 0.305 0.330 0.305 0.330 0.312 0.330 0.320 0.320
Expected Targets and Tolerances
The measured parameters should be “x, y” coordinates.
The White Balance alignment should be performed using a contact less analyzer (ei: Minolta
CA-210). The analyzer may not touch the screen surface, and measurement must be performed in a
dark environment keeping the probe(s) at 90+/-2° from the panel.
The result should measure up the relevant spec.
2.4 High Pot. and Insulating Resistance Tests
At the end of the process, a High Pot. and an Insulating Resistance tests are required for
matching Safety Electrical requirements (ei: xxxx)
High Voltage Withstanding requirements
- “Voltage” Ö3500 VAC
- “Max Leakage Current” Ö10mA
- “Test Time” Ö5 sec
Insulating Resistance requirements
- “Voltage” ÖDC500V
- “Threshold Min” Ö4M
¡
- “Test Time” Ö3 sec

3.Factoryde f a u lt settings
Do the “Reset shop” before packing.The detail of reset shop follow OOB setting.
“Factory Menu” Definition
1)
ˊ
Hotkey
Item Sub-item Value Note
Hotkey Off/On OFFġhotkey is invalid
ON ġhotkey(Return key) is availability
2)
ˊ
Burning Mode

Factory Alignment Specification of normal SIACP
Page 9 of 12
Item Sub-item Value/Sub-item Note
Burning
Mode
Off/On Select panel On with left/right
key, Press “EXIT” key to enter
the burning mode;
Press “Menu” key on keyboard
to exit the burning mode
3)
ˊ
ADC
˄
Need not to do ADC when alignment
˅
4)
ˊ
W
hite Balance
Item Sub-item Value Note
Source HDMI,etc For balance source˖
HDMI,VGA,DTV,PAL,SECAM,NTSC,Scar
t RGB,CPM, HDMI
Color Temperature Normal
/Warm/Cool 
The value of Warm and cool is the offset
of Normal mode. Cool is the preset status
R Gain R White balance
G Gain G White balance
B Gain B White balance
R Offset R Gray balance
G Offset G Gray balance
B Offset B Gray balance
White Balance Init Press “Right” key to initial the preset RGB
Gain/Offset value
Pic. Enhance On/Off Press “Right” key to switch off all of the
items in the feature submenu. This should
be done before white balance alignment.
If it’s off, the way to switch it on is to reset
user/shop or set on the features in
Feature sub-item manually.
Picture related Flesh tone Select On/Off to open/close the function
Adaptive luma
control
Select On/Off to open/close the function
Light sensor Select On/Off to open/close the function
Dynamic
backlight
Select Auto/High/Mid/Low to set the
backlight control
White
Balance
Back light 0~100 Set the backlight
5)
ˊ
Reset Shop
Item Sub-item Value Note
Reset
Shop
Clear date of NVM in user menu,include
the value related installation,and Clear
date of factory menu except the item of
Balance and sound ,set to default value

Factory Alignment Specification of normal SIACP
Page 10 of 12
6)
ˊ
Reset ALL
Item Sub-item Value Note
Reset
ALL
Clear NVM valuesˈand set to default
value
7)
ˊ
Power Mode
Item Sub-item Value Note
Power
Mode
Boot/Standby/
Last Status
Boot: Enter power on mode
Standby: Enter standby mode
Last Status: power on according to last
status
8)
ˊ
USB Clone Mode
Item Sub-item Value Note
USB Clone Mode All/ChannelList
/EEPROM/
User Setting
Select to choose the things you want to
clone
TV TO USB DO Press “Right” key to copy the
data(WB,ADC,picture setting,etc) to USB
USB
Clone
Mode
USB TO TV DO Press “Right” key to set the
data(WB,ADC,picture setting) from USB
9)
ˊ
Other
Item Sub-item Value Note
Project ID ***
Project Name ***
Panel ID ***
Panel ***
Version ***
Date ***
Time ***
MCU Version ***
RCU ***
PSU ***
Region ***
Project
info
Product S/N ***
Tuner
AGC

Factory Alignment Specification of normal SIACP
Page 11 of 12
Appendix
n
“HowtodownloadFLASHSW”
Prepare MTK SW tool for update.
1. Connect the PC to the serial connector on board using a special serial device (USB or
COMx).
2. Provide the a correct voltage to the board
3. Start “MTKTOOL.exe” application under MTKxx folder, and set the parameters as below
picture(notice:select MT536X chassiss):
4. Press “Browse” button to select the corresponding SW bin file to upload
5. Press “Upgrade” button then press “NOR” button to start downloading the SW and wait the
gauge displayed “100%” that means the SW has been successfully downloaded.
In the meanwhile, all operations such erasing flash and so… are parsed into the debug
window script.
6. Once the SW is downloaded, switch-off/on the chassis board and wait few seconds for
eeprom update.
Appendix
o
“HowtoupgradeFLASHSWfromUSB”
Upgrade with loader:
1. Save the new software file(*.pkg) in the root directory of USB, and modify it’s name as
upgrade.pkg.
2. Plug in the USB when TV set is “power off” or “standby” (TV set should be on “standby” status
if using a touch sensing keyboard).
3. Press down “power” key on keyboard, power on if it is on “power off” status , release the
“power” key 2~5 second later , the LED on IR board will flash after upgrade begin, the TV set
will start up if upgrade succeed.The LED is on but no flash if upgrade fail,check the set and

Factory Alignment Specification of normal SIACP
Page 12 of 12
try again.
Upgrade without loader(The TV set should be able to display normally):
1. Save the new software file(*.pkg) in the root directory of USB, and modify it’s name as a
software number, such as “V8-0MT1006-LF1V017.pkg”.
2. Plug in the USB.
3. Upgrade the SW follow the indication display on the screen
Appendix
p
“ModifypanelIDwithRC”
“Modify panel ID without panel but via a RC”
¾062598+MENU+xxx (xxx:Panel ID)