Tcp Smartstuff smartbox User manual

SmartStuff SmartBox

+ Panel Sensor

Item Number: SMBOXPLBT

WARNING

WARNING: DANGER–RISK OF SHOCK–

DISCONNECT POWER BEFORE INSTALLATION!

NOTE: This device is suitable for damp

locations only.

•This product is used to control lighting luminaires with

0-10V dim to off drivers/ballast.

• This product must be installed in accordance with local

and national electrical codes. Please consult with a

qualified electrician before installation.

NOTE: Please read the instructions before

proceeding with the installation.

FCC

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) This device must accept any interference received,

including interference that may cause undesired operation.

Warning: Changes or modiﬁcations to this unit not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant

to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy

and, if not installed and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in an installation. If this equipment

does cause harmful interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

—Reorient or relocate the receiving antenna.

—Increase the separation between the equipment and receiver.

—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

—Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.

This equipment should be installed and operated with minimum distance 8 inches between the radiator & your body.

Speciﬁcations

Input Voltage

• 120 – 277VAC @ 15mA

Input Line Frequency

• 50/60Hz

Maximum Power

• 1W

Output Voltage

• 0-10VDC

Operating Temperature

• -23°F to 113°F

Humidity

• <80% RH

Radio Protocol

• Bluetooth Signal Mesh

Communication Range

• 150 ft / 46 m

SmartBox + Panel Sensor Setting:

Microwave Maximum Height........ 10 feet / 3m

Microwave Maximum Diameter.... 33 feet / 10m

PIR Maximum Height .................... 10 feet / 3m

PIR Maximum Diameter............. 16 feet / 5.0m

Sensor Detection Angle.............................360°

Hold Time............................. 1 min. –1092 min.

Daylight Sensor Setpoint ............... 0 – 300 lux

Regulatory Approvals

• ETL Listed

• Contains FCC ID: NIR-MESH8269

• Contains IC: 9486A-MESH8269

• Conforms to UL 8750

• Certified to CSA C22.2 No. 250.13

Installation of the SmartBox + Panel Sensor

Check the label on

the SmartBox for correct

orientation and Install

as shown. The junction

box needs a 1/2" knock-

out for the SmartBox +

Panel Sensor to fit

securely. Use double-

sided tape if needed.

½"

Switch between Microwave Sensor and PIR Sensor.

PIR sensorMicrowave sensor

Electrical Connections

Make the electrical

connections as shown.

SmartBox +

Panel Sensor

Luminaire Driver L N

LDIM+ DIM- N

black(18AWG)

purple

(22AWG)

gray

(22AWG)

white(18AWG)

(120-277v)

Maintain a minimum distance of 4.92 ft / 1.5m between:

• A window and the SmartBox + Panel Sensor.

• The SmartBox + Panel Sensor and other TCP SmartStu products with a Microwave Sensor.

Make sure no light is reected in the direction of the SmartBox + Panel Sensor

LIMITED WARRANTY: This product is warranted for a period of 5

YEARS* from date of original purchase against defects in materials

and workmanship. If this product should fail to operate due to

defects in material or workmanship, simply call 1-800-771-9335 within

5 YEARS of purchase. This product will be repaired or replaced, at

TCP’s option. This warranty is expressly limited to repair or replace-

ment of the product. This warranty gives the consumer specific legal

rights, which vary from state to state. WARRANTY IS VOID IF PROD-

UCT IS NOT USED FOR THE PURPOSE FOR WHICH THIS PRODUCT

IS MANUFACTURED.

TCP SmartStuff App

The TCP SmartStuff App is used to configure the Bluetooth®

Signal Mesh and TCP SmartStuff devices.

Download the TCP SmartStuff App using the following options:

• Download the SmartStuff App from the

Apple App Store or Google Play Store

• Use the QR Codes here:

Instructions for conﬁguring TCP Smart App and SmartStuff

devices are at https://www.tcpi.com/tcp-smartstuff/

This device complies with Innovation, Science and Economic Development Canada licence-exempt RSS standard(s).

Operation is subject to the following two conditions:

(1) this device may not cause interference, and

(2) this device must accept any interference, including interference that may cause undesired operation of the device.

Le présent appareil est conforme aux CNR d'ISED applicables aux appareils radio exempts de licence.

L'exploitation est autorisée aux deux conditions suivantes:

(1) l'appareil ne doit pas produire de brouillage, et

(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible

d'en compromettre le fonctionnement.

This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. This

equipment should be installed and operated with a minimum distance of 20 cm between the radiator & your body.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Le rayonnement de la classe b repecte ISED fixaient un environnement non contrôlés.Installation et mise en œuvre

de ce matériel devrait avec échangeur distance minimale entre 20 cm ton corps.Lanceurs ou ne peuvent pas

coexister cette antenne ou capteurs avec d’autres.