TDE MACNO 374I00070V User manual

Cod.MA00101E00V_1.3 (ex.MSMODE0010E0)
Accessories Tde Macno
User’s Manual
Usb RS485-232 converter (374I00070V)

MA00101E00 V_1.3
1
INDEX
INDEX...........................................................................................................1
1INSTALLATION DOCUMENTS ..............................................................2
2CONNECTIONS .....................................................................................2
3SERIAL LINE ..........................................................................................3
4LED DESCRIPTIONS .............................................................................4
5DIPSWITCH DESCRIPTIONS................................................................4
6SOLDER SWITCH..................................................................................5
7the concept of the sistem........................................................................5
7.1 When a TX data as transmitted both the others ports receive that data................. 5
8OPTION “MONITOR”..............................................................................6

2
MA00101E00 V_1.3
1 INSTALLATION DOCUMENTS
Follow this link: http://www.ftdichip.com/Documents/InstallGuides.htm
Drivers link: http://www.ftdichip.com/Drivers/VCP.htm
Drivers from TDEMACNO website (direct link): USB RS485-232 CONVERTER DRIVERS
2 CONNECTIONS
Connect the drive to the PC by RS485-232 converter and install the drivers in the PC. After that open the
supervisor OPDExplorer and set the Modbus comunication with these info:
•COM port of the PC;
•Address (P92) of the drive;
•Baud rate (P93) of the drive.
Now the PC is ready to be connected with the drive.
Connect USB to the PC
Connect Serial cable
to the drive

MA00101E00 V_1.3
3
CN3 RS422/RS485
CN2 RS422/RS485
CN4 RS232
1: GNDExt
1:+5Ext
1:n.c.
2: RX+
2: RX+
2:TX-232
3: TX+
3: RX-
3:RX-232
4: K2=close Term -
4: TX+
4:n.c.
5: Term +
5: TX-
5:GNDExt
6: RX-
6: GNDExt
6:n.c.
7: TX-
7:n.c
8: PROG pin
8:n.c
9: Term -.
9:(opt “MONITOR”=RX-USB)
3 SERIAL LINE

4
MA00101E00 V_1.3
The serial line present on OPDE / MiniOPDE drives has connection capability for “4-wire” data transmission
and therefore it can communicate in full-duplex mode. As a fact, by virtue of the protocol used
(MODBUS RTU), it always communicates in “half-duplex” mode, wherefore you can make the connection
with just “two wires” by connecting RX and TX and /RX and /TX between them.
In connector J1 (OPDE) / J3 (MiniOPDE), RX and /RX signals are the reception signals for the drive, while
TX and /TX are the transmission signals.
Impedances are fitted inside the drive to “terminate” the connection (120Ω) and polarize the line. To use this
terminal, connect between them terminals 5 - 3 and 9 - 7 of connector J1 (OPDE) / J3 (MiniOPDE) (for the
last drive in the line only).
Communication wires must be twisted.
4 LED DESCRIPTIONS
LED
Descriptions
L1
RX-RS232
L2
TX-RS232 (option “MONITOR”=RX-USB)
L3
RX-USB
L4
TX-USB
L5
RX-RS422/RS485
L6
ENABLE TX-RS422/RS485
L7
TX-RS422/RS485
L8
POWER SUPPLIES +5VExt
5 DIPSWITCH DESCRIPTIONS
Correct
setting

MA00101E00 V_1.3
5
N.PIN
Descriptions
1
PROG. -> On=Converter in program mode Off= terminal mode
2
Term+ ON = Term+ and PullUp on the rx+ line (only in the first and the last
receivers)
3
ON = RS485 2wire OFF= RS422 4wire
4
Term- ON = Term- and PullDw on the rx- line (only in the first and the last
receivers)
Open/Close both dip2 and dip4 together for bus termination.
Be carefull do not leave the floating potential GNDExt but fix it on the ground in just only one point.
6 SOLDER SWITCH
Solder switch monitor
options
Default = RS232
Monitor options
K1
1-2 Closed / 2-3Open
1-2 Open / 2-3 Closed
K3
Closed
Solder switch
Descriptions
K2
Close only for compatibility with old OPD
K7
Power supplies from USB when use RS232 to RS422
without USB initialization/use
7 THE CONCEPT OF THE SISTEM
7.1 WHEN A TX DATA AS TRANSMITTED BOTH THE OTHERS PORTS RECEIVE
THAT DATA
These three examples show the relationship between the sender and who receivers.
If we don't use the USB connector the converter need an external 5V on USB connector or from the pin1-6 of
CN2.It is possible to use a normal USB power supplies on the USB cable but the internal K7 solder switch
must be close.

6
MA00101E00 V_1.3
8 OPTION “MONITOR”
The "Monitor" option allows to receive on the RS232 pin2 connector the data transmitted from the RS485 and,
on the pin9, the data from USB. To do this, please close K3 and open (with a cutter) the short circuit K1 (1-2)
and closed K1 (2-3).