TDRFORCE 540E User manual

with Warranty Card
RV/MARINE WATER PRESSURE PUMP
INSTRUCTION
5 4 0 E / 5 3 0 E / 5 4 0 F / 5 3 0 F
www.tdrpump.com
www.tdrpump.com
www.tdrpump.com
www.tdrpump.com
www.tdrpump.com
www.tdrpump.com
www.tdrpump.com
www.tdrpump.com
www.tdrpump.com

1
Cautions
1.After unpacking the pump, please check if it has been damaged during transport. If so, please contact
TDRFORCE online services at the first time.
2.Make sure that the main voltage corresponds to the voltage specified on the instruction manual.
3.The motor must be absolutely grounded before any other operation.
4.Do not submit the pump body to mechanical stress.
5.The pump must be sheltered from weather ( sun- rain- wind- snow- chill).
6.The pump could be only used in fresh water circulating.
7. The pump should be installed on a solid surface.
8. The pump should be connected to proper sized wiring.
www.tdrpump.com
www.tdrpump.com
www.tdrpump.com
www.tdrpump.com
www.tdrpump.com
www.tdrpump.com
www.tdrpump.com
www.tdrpump.com
www.tdrpump.com

2
9. The pump should be installed under proper electrical protection.
10. The pump should be installed in minimized flow restrictions in the system.
Technical Specifics
MODEL VOLTS CHAMBERS
Pressure
(PSI)
Pressure
(BAR)
FLOW
RATE
H-MAX REV POWER
CERTIFICATIO
N
MOTOR LIFE
CONTINUOUS
WORKING TIME
540E 110V
AC 4 75 5.1
BAR
5.5
GPM 170FT 2400rpm 172.5W CE
more than
1500
hours
40mins
540F 12V DC 4 70 4.8
BAR 5 GPM 157FT 2300rpm 180W CE
more than
1500
hours
40mins
530E 110V
AC 3 45 3.1
BAR 4 GPM 102FT 2400rpm 143W CE
more than
1500
hours
40mins
530F 12V DC 3 45 3.1
BAR 4 GPM 102FT 2300rpm 105W CE
more than
1500
hours
40mins
www.tdrpump.com
www.tdrpump.com
www.tdrpump.com
www.tdrpump.com
www.tdrpump.com
www.tdrpump.com
www.tdrpump.com
www.tdrpump.com
www.tdrpump.com

3
GENERAL INFORMATION
The patent has been designed for delivering smooth and consistent flow at all ranges of operation while
drawing low current. The balanced motor design incorporates with precision ball bearings for long life, and
is equipped with an integral thermal breaker. Full corrosion-resistant shell and environmental thermoplastic
construction ensure less prone to mechanical failure. What’s more, the submersible pump impeller blade
features highly corrosion-resistant impeller that automatically adjusts to speed and fluid viscosity to ensure
long service life.
Tips:
The manufacturer will do test for every single product, for which a small amount of water may remain in the
pump. This does not mean that the pump has been used.
www.tdrpump.com
www.tdrpump.com
www.tdrpump.com
www.tdrpump.com
www.tdrpump.com
www.tdrpump.com
www.tdrpump.com
www.tdrpump.com
www.tdrpump.com

4
www.tdrpump.com
www.tdrpump.com
www.tdrpump.com
www.tdrpump.com
www.tdrpump.com
www.tdrpump.com
www.tdrpump.com
www.tdrpump.com
www.tdrpump.com

5
NO Component
1 Pressure switch
2 Pump head
3 Valve plate assembly
4 Diaphragm/ Drive assembly
5 Motor
www.tdrpump.com
www.tdrpump.com
www.tdrpump.com
www.tdrpump.com
www.tdrpump.com
www.tdrpump.com
www.tdrpump.com
www.tdrpump.com
www.tdrpump.com

6
Troubleshooting
TYPE OF DEFECT CAUSE SOLUTION
The motor does not start
- False electric connections
- Make sure the power cord is
accurately plugged
- Low inlet water pressure - Increase water flow of inlet
The motor is running, but
no water pumped
- The operating voltage is unstable
- Ensure that the power source is
in accord with the instructions
- The water inlet pipe is bent or
attached to the barrel wall
- Unblock the pipeline to make the
water run smoothly
- Some blockages in the pump or
motor
- Remove the blockages and avoid
pumping impurity water
- The water pump was used to pump
corrosive liquid, which caused the
- Avoid pumping corrosive liquids
www.tdrpump.com
www.tdrpump.com
www.tdrpump.com
www.tdrpump.com
www.tdrpump.com
www.tdrpump.com
www.tdrpump.com
www.tdrpump.com
www.tdrpump.com

7
rubber sealing ring to shrink, expand,
oxidize and become non-sealing.
- Thread damage of the screw
- Connect proper screw and seal
with Teflon tape
Pump starts and stops
frequently
- Diaphragm broken - Disposal
Pump does not stop
- The pump is over-pressure
- Adjust the pressure screw
counterclockwise to release the
pressure
- The pump does not provided
sufficient pressure
- Adjust the pressure screw
clockwise to increase the pressure
- Leakage on the outlet plumbing - Fix the leakage
www.tdrpump.com
www.tdrpump.com
www.tdrpump.com
www.tdrpump.com
www.tdrpump.com
www.tdrpump.com
www.tdrpump.com
www.tdrpump.com
www.tdrpump.com

8
Pump suddenly quit
working
- Overheat protection starts
- Restart the pump until it's
cooling
- Power off - Turn on again
- Motor burns out - Disposal
- Switch burns out - Disposal
Pump vibrates and
operates noisily
- Air in the water inlet pipe
- Fix the inlet leakage and make
the pipes firmly connected
Pump head leakage
- Diaphragm broken.
- The screw of the pump head is loose.
- The bypass switch is loose.
- Pump pressure setting is too high.
- Pump head is damaged.
- Disposal
- Tighten the screw
- Tighten the screw
- Adjust the pressure switch.
- Disposal
Pressure switch burned out - Frequent on and off - Disposal
www.tdrpump.com
www.tdrpump.com
www.tdrpump.com
www.tdrpump.com
www.tdrpump.com
www.tdrpump.com
www.tdrpump.com
www.tdrpump.com
www.tdrpump.com

9
- Pressure setting too high, overloaded
operation
- Adjust the pressure screw
counterclockwise to release pressure
Pump supplies insufficient
flow
- The diaphragm is jammed or blocked - Disposal
- The inlet flow rate is too small - Increase the inlet water flow
www.tdrpump.com
www.tdrpump.com
www.tdrpump.com
www.tdrpump.com
www.tdrpump.com
www.tdrpump.com
www.tdrpump.com
www.tdrpump.com
www.tdrpump.com

10
Customer contact, please keep it properly.
Dear customer:
Thank you for choosing products of TDRFORCE. In order to provide you with more satisfactory service and better protect
your rights, please read this regulation carefully and keep the warranty card properly.
Regulations:
1.For any quality issue of TDRFORCE product within 180 days after sale, we offer no-hassel return service for our
customers;
3.Valid evidence of purchase will be essential such as order ID or warranty card;
4.Valid evidence showing product problems shall be provided in the contact such as videos, photos or detailed descriptions.
5.Warranty card shall be filled out and attached with the return product.
Please notice:
The following situations are not applicable to our no-hassel return policy.
1. Product damage caused by installation or use not in accordance with the instruction manual;
2. Product beyond 180 days after sale;
3. Product return with no reason;
4. Product damage caused by self-disassembly or sabotage;
5. Product damage caused by force majeure such as earthquakes, fires, etc.
www.tdrpump.com
www.tdrpump.com
www.tdrpump.com
www.tdrpump.com
www.tdrpump.com
www.tdrpump.com
www.tdrpump.com
www.tdrpump.com
www.tdrpump.com
www.tdrpump.com

11
Warranty Card
Buyer’s Name:
Tel:
E-mail:
Order ID:
Return Address:
Product Problem Description:
www.tdrpump.com
www.tdrpump.com
www.tdrpump.com
www.tdrpump.com
www.tdrpump.com
www.tdrpump.com
www.tdrpump.com
www.tdrpump.com
www.tdrpump.com
This manual suits for next models
3
Table of contents
Other TDRFORCE Water Pump manuals
Popular Water Pump manuals by other brands

AQUA FORTE
AQUA FORTE AP Series manual

Little Giant
Little Giant WGFP-15 user manual

Little Giant
Little Giant 9E-CIA-RFS quick start guide

Aqua Medic
Aqua Medic SP 1500 Operation manual

E-one
E-one Extreme WH47 Series Typical Installation Instructions & Warranty Information

Waterco
Waterco Alphaflo ECO-V 100 operating guide