Power Fist 8645830 User manual

V 4.0 8645830
User Manual
1/3HPSumpPump
Please read and understand all instructions before use. Retain this manual for
future reference.

8645830 1/3 HP Sump Pump V 4.0
SPECIFICATIONS
Max. Flow Rate 3,036 GPH
Horsepower 1/3 HP
Voltage Rating 115V
Current Rating 3.9A
Inlet / Outlet Ports 1 & 1-1/4 in.
Max. Suction Lift 23 ft.
Max. Discharge Head 20 ft.
Housing Material Cast Aluminum
Impeller Material Plastic
Flow Rate @ 5 feet 2,376 GPH
Flow Rate @ 10 feet 1,769 GPH
Flow Rate @ 15 feet 1,161 GPH
Flow Rate @ 20 feet 132 GPH
Float Switch
Tethered
Cord Length 10 ft.
Application(s) Garden Use
UL/CUL UL/CUL#E248578
1/3HPSumpPump
2 For technical questions call 1-800-665-8685

V 4.0 1/3 HP Sump Pump 8645830
SAFETY
WARNING! Read and understand all instructions before using this tool. The operator
must follow basic precautions to reduce the risk of personal injury and/or damage
to the equipment.
SAVE THESE INSTRUCTIONS
Keep this manual for safety warnings, precautions, operating or inspection and
maintenance instructions.
HAZARD DEFINITIONS
Please familiarize yourself with the hazard notices found in this manual. A notice is an
alert that there is a possibility of property damage, injury or death if certain instructions
are not followed.
DANGER! This notice indicates an immediate and specific hazard that will result in
severe personal injury or death if the proper precautions are not taken.
WARNING! This notice indicates a specific hazard or unsafe practice that could
result in severe personal injury or death if the proper precautions are
not taken.
CAUTION! This notice indicates a potentially hazardous situation that may result in
minor or moderate injury if proper practices are not taken.
NOTICE! This notice indicates that a specific hazard or unsafe practice will result
in equipment or property damage, but not personal injury.
WORK AREA
1. Operate in a safe work environment. Keep your work area clean, well-lit and free
of distractions.
2. Keep anyone not wearing the appropriate safety equipment away from the
work area.
3. Store unused tools properly in a safe and dry location to prevent rust or damage.
Lock tools away and keep out of the reach of children.
4. Do not install or use in the presence of flammable gases, dust or liquids.
PERSONAL SAFETY
WARNING! Wear personal protective equipment approved by the Canadian Standards
Association (CSA) or American National Standards Institute (ANSI).
Visit www.princessauto.com for more information 3

8645830 1/3 HP Sump Pump V 4.0
PERSONAL PROTECTIVE EQUIPMENT
1. Always wear impact safety goggles that provide front and side protection for the
eyes. Eye protection equipment should comply with CSA Z94.3-07 or ANSI
Z87.1 standards based on the type of work performed.
2. Wear gloves that provide protection based on the work materials or to reduce the
effects of tool vibration.
3. Wear protective clothing designed for the work environment and tool.
4. Non-skid footwear is recommended to maintain footing and balance in the
work environment.
5. Wear steel toe footwear or steel toe caps to prevent a foot injury from
falling objects.
6. Wear a NIOSH approved respirator when working on materials that produce
hazardous fumes, dust or particulate matter.
PERSONAL PRECAUTIONS
Control the tool, personal movement and the work environment to avoid personal injury
or damage to tool.
1. Do not operate any tool when tired or under the influence of drugs, alcohol
or medications.
2. Avoid wearing clothes or jewelry that can become entangled with the moving parts
of a tool. Keep long hair covered or bound.
3. Do not overreach when operating a tool. Proper footing and balance enables better
control in unexpected situations.
SPECIFIC SAFETY PRECAUTIONS
WARNING! DO NOT let comfort or familiarity with product (gained from repeated use)
replace strict adherence to the tool safety rules. If you use this tool unsafely or
incorrectly, you can suffer serious personal injury.
1. Use the correct tool for the job. This tool was designed for a specific function.
Do not modify or alter this tool or use it for an unintended purpose.
2. Wear safety glasses when working with pumps.
3. Do not run the pump if there is no water in the system.
4. Do not uses pumps in water over 40°C (104°F). Avoid draining hot water tanks
into sump pits.
5. Do not power this device with anything other than a 120 volt power source.
4 For technical questions call 1-800-665-8685

V 4.0 1/3 HP Sump Pump 8645830
6. Connect this product to a grounded circuit equipped with a Ground Fault Circuit
Interrupter (GFCI) device.
7. Do not install the pump in any location classified as hazardous by the National
Electrical Code, ANSI / NFPA 80-1984 or the Canadian Electrical Code.
8. Do not use pumps for pumping mud, sand, cement, fats, salt, waste water from
toilets, oils, combustible or explosive substances or chemicals.
9. The appliance is intended for pumping rainwater, fresh water, mains water and
chlorinated swimming pool water.
10. The pump must not be used for drinking water supply or for the delivery
of foodstuffs.
11. The device is not suitable for commercial or industrial use.
12. The pump is not suitable for continuous running (such as permanent circulation in
filter systems).
13. Risk of fire or explosion. Do not pump flammable or explosive fluids such as
gasoline, fuel oil, kerosene, etc.
14. Do not use in a flammable and / or explosive environment.
15. Before installing this product, have the electrical circuit checked by an electrician
to ensure proper grounding.
16. Do not lift the pump by the power cord.
17. Be certain the pump power source is disconnected before installing or servicing
the pump.
18. Check the voltage on the motor nameplate and make sure that the line voltage of
the electrical current supply is the same.
19. Do not expose the pump to freezing temperatures. Freezing could cause severe
damage and will void the warranty.
20. Do not insert fingers or any object into the pump or motor openings.
21. Do not run the pump dry. Dry running can overheat the pump, (causing burns to
anyone handling it) and will void the warranty.
22. The pump normally runs hot. To avoid burns when servicing the pump, allow it to
cool for twenty minutes after shutdown before handling it.
23. Always check the pump before each operation. A damaged pump must not be
used. Have the pump serviced by a qualified service technician.
Visit www.princessauto.com for more information 5

8645830 1/3 HP Sump Pump V 4.0
ELECTRICAL SAFETY
WARNING! Hazardous voltage can shock, burn or kill. When installing, operating or
servicing this pump, follow the safety instructions listed below.
1. Do not allow the plug on the end of the electrical cord to be submerged.
2. Do not use extension cords. They are a fire hazard and can reduce the voltage
sufficiently to prevent pumping and / or damage the motor.
3. Do not handle or service the pump while it is connected to the power supply.
4. Ground the motor before connecting to an electrical supply.
5. Failure to ground the motor can cause severe or fatal electrical shock.
6. Do not ground to a gas supply line.
7. To avoid dangerous or fatal electrical shock, turn off the power to the motor before
working on electrical connections.
8. The supply voltage must be within 10% of the nameplate voltage. Incorrect voltage
can cause fire or seriously damage the motor and voids the warranty. If in doubt,
contact a licensed electrician.
9. Meet all national electrical code and local codes for all wiring.
10. Do not handle a pump or pump motor with wet hands, or when standing on a wet
or damp surface or in water.
11. Always disconnect the power source before performing any work on or near the
motor or its connected load.
12. Protect yourself against electric shocks when working on electrical equipment.
Avoid body contact with grounded surfaces. There is an increased chance of
electrical shock if your body is grounded.
13. The fuse must be a residual current circuit-breaker with a measured residual
current of no more than 30 mA.
14 If the device is not in use, make sure that the plug is removed from the
power source.
15. Make sure that the device is switched off before plugging in the mains cable.
16. Make sure that the device is switched off before unplugging it.
17. Disconnect the power supply before moving or transporting the device.
18. Do not install and switch on the pump if there are people or animals in
the medium, or have contact with the medium being pumped (such as
swimming pools).
WARNING! A qualified electrician should perform all wiring.
6 For technical questions call 1-800-665-8685

V 4.0 1/3 HP Sump Pump 8645830
POWER CORD
1. Do not operate this tool if the power cord is frayed or damaged as an electric
shock may occur, resulting in personal injury or property damage.
a. Inspect the tool's power cord for cracks, fraying or other faults in the
insulation or plug before each use.
b. Discontinue use if a power cord feels more than comfortably warm while
operating the tool.
c. Have the power cord replaced by a qualified service technician.
2. Keep all connections dry and off the ground to reduce the risk of electric shock.
Do not touch plug with wet hands.
3. Prevent damage to the power cord by observing the following:
a. Never use the cord to carry the tool.
b. Do not pull on the cord to disconnect the plug from an outlet.
c. Keep the power cord clear of the tool and the tool's work path while in
operation. The cord should always stay behind the tool.
d. Keep cord away from heat, oil, sharp edges or moving parts.
4. Do not allow people, mobile equipment or vehicles to pass over unprotected
power cords.
a. Position power cords away from traffic areas.
b. Place cords in reinforced conduits.
c. Place planks on either side of the power cord to create a protective trench.
UNPACKING
WARNING! Do not operate the tool if any part is missing. Replace the
missing part before operating. Failure to do so could result in a malfunction
and personal injury.
Remove the parts and accessories from the packaging and inspect for damage.
Visit www.princessauto.com for more information 7

8645830 1/3 HP Sump Pump V 4.0
IDENTIFICATION KEY
ASSEMBLY & INSTALLATION
When this manual refers to a part number, it refers to the included Parts
Identification section.
HOSE CONNECTION
NOTE: All threaded connections must be sealed with thread sealing tape.
1. Attach a sufficiently long and strong rope to the handle before the first use. The
pump is submerged into the liquid on this holding rope and can also be carried
with it as well as with the handle.
NOTE: In case of continuous use of the pump with the rope, the condition of the
rope must be checked regularly as it can decay and break over time.
2. Connect the pressure pipe onto the pressure connection. For occasional use, use a
suitable water hose. The use of rigid pipes with a non-return valve is
recommended for use at a fixed location. This prevents the return flow of liquid
when switching the pump off.
NOTE: When using a hose, screw a suitable hose adapter onto the pressure
connection. Push the hose firmly onto the hose adapter and secure with a
hose clamp.
1 Carrying Handle
2 Hose Adapter for Pressure Connection
3 Pump Casing
4 Float Switch
8 For technical questions call 1-800-665-8685

V 4.0 1/3 HP Sump Pump 8645830
FLOAT SWITCH ADJUSTMENT
The cut-in / cut-out height of the pump can be adjusted by shortening the length of the
float cord.
LOCATION
1. The pump needs an area of at least
19.7 x 19.7 in. (50 x 50 cm). The float
switch must be able to move freely so
that it functions properly.
2. Make sure to locate the pump in a
stable position (especially for
automatic operation).
3. Make sure that the pump is located in
a way that ensures the inlet openings
at the suction base are unobstructed.
Place the pump on a brick or cement,
do not place the pump directly on
open earth or gravel.
4. Do not use the power cable or float switch to carry or hang the pump. When
submerging the pump, use a rope fastened to the pump’s carrying handle.
OPERATION
1. Submerge the pump at an angle into the liquid
to be pumped so that no air pocket forms on
the underside of the appliance. Suction would
be prevented by this air pocket. Once the
pump is submerged, it can be righted again.
2. Leave the pump on the bottom of the liquid
source. Use a strong rope attached to the
carrying handle of the pump for lowering.
3. Tighten the end of the rope firmly
after lowering.
NOTE: The pump can also be operated while
suspended on a rope.
CAUTION! Do not operated the pump without a pressure hose.
Visit www.princessauto.com for more information 9

8645830 1/3 HP Sump Pump V 4.0
CAUTION! Avoid allowing the pump to twist around its longitudinal axis.
4. After the pump has been connected to the main power supply, the pump will
begin operating.
CATUION! The float switch must be able to move so that the submersible pump
cannot run dry.
OPERATING TIPS
1. Dry-running operation causes increased wear and is to be avoided. Therefore, the
pump must be immediately switched off when water fails to flow.
2. After having pumped chlorinated swimming pool water or other liquids leaving
residues, the pump should be rinsed with clean, clear water.
3. Sand and other abrasive materials in the liquid cause increased wear and reduce
the pump’s output.
4. Avoid running the pump for more than 10 minutes at a time.
NOTE: This flat suction height is only reached in case of manual operation, but not in
case of automatic operation.
5. If the pump becomes air locked, shut the power off for approximately 1 minute
then restart the pump. Repeat several times to clear the air from the pump.
CARE & MAINTENANCE
WARNING! Disconnect the mains plug before carrying out any work on the device.
WARNING! Make sure that the device and connected accessories are depressurized
before carrying out any work on the device.
WARNING! All gaskets must be replaced after each disassembly of components.
1. Maintain the tool with care. A tool in good condition is efficient, easier to control
and will have fewer problems.
2. Make certain that the power source conforms to the requirements of
your equipment.
3. When wiring an electrically driven device, follow all electrical and safety codes, as
well as the most recent Canadian Electrical Code (CE) and the Canadian Centre for
Occupational Health and Safety (CCOHS).
4. Always disconnect the pump from the power source prior to repairs. Always
reconnect the pump to the power source after the repairs.
10 For technical questions call 1-800-665-8685

V 4.0 1/3 HP Sump Pump 8645830
5. Inspect the tool fittings, alignment, hoses and power supply cord periodically. Have
damaged or worn components repaired or replaced by an authorized technician. Only
use identical replacement parts when servicing.
6. Only use accessories intended for use with this tool.
7. Maintain the tool’s labels and name plates. These carry important information. If
unreadable or missing, contact Princess Auto Ltd. for replacements.
WARNING! Only qualified service personnel should repair the tool. An improperly
repaired tool may present a hazard to the user and/or others.
CLEANING
Rinse with clean water. Remove stubborn contamination with a brush and detergent.
Submerge the pump in a container with clean water and switch on for a short time to
rinse the inside of the pump.
CLEANING THE SUCTION AREA
Clean all accessible insides of the casing. Remove fibres which have wound around the
rotor shaft by opening the pressure connection. Remove stubborn contamination with a
brush and detergent.
NOTE: Before using the pump again, first soak the pump so that any possible dirt
residues do not block the appliance.
MAINTENANCE SCHEDULE
BEFORE EACH USE
1. Perform a visual inspection of the pump casing and cables for damage.
2. Check the float switch for damage by lifting and shaking the switch to check the
free movement of the contained metal balls.
AFTER EVERY USE
Clean the pump thoroughly.
LUBRICATION
NOTICE! NEVER use a penetrating oil to lubricate the tool. Penetrating oil may act
as a solvent that can break down the grease and cause the tool to seize up.
Visit www.princessauto.com for more information 11

8645830 1/3 HP Sump Pump V 4.0
STORAGE
The pump should not be stored outside; the pump could get damaged from rain and ice.
Keep the pump in a cool, dry place. Do not store the pump in direct sunlight.
REMOVAL FROM STORAGE
Before using the pump again, first soak the pump so that any possible dirt residues do
not block the appliance.
DISPOSAL
Recycle a tool damaged beyond repair at the appropriate facility.
TROUBLESHOOTING
Visit a Princess Auto Ltd. location for a solution if the tool does not function properly or
parts are missing. If unable to do so, have a qualified technician service the tool.
Problem(s) Possible Cause(s) Suggested Solution(s)
Pump does not run. No power. Check the cables, plug,
socket and fuse.
Motor overheats. Liquid temperature is too
high, eliminate the cause
of overheating.
Blocked by foreign
contaminants, eliminate the
cause of overheating.
Ground Fault Circuit
Interrupter (GFCI)
is activated.
Switch on the GFCI, if it
happens again, contact a
qualified service technician.
12 For technical questions call 1-800-665-8685

V 4.0 1/3 HP Sump Pump 8645830
Problem(s) Possible Cause(s) Suggested Solution(s)
Pump runs but does not
pump liquids.
Suction opening is blocked. Remove the blockage.
The pump draws in air. Keep the pump at an
angle while submerging.
Switch the pump on and
off several times in order
to expel the air.
The pump is blocked by
foreign contaminants.
Clean the pump.
The delivery rate is
too low.
The delivery height is
too great.
Reduce the delivery
height to the
maximum height
(see Specifications).
The pressure line diameter
is too small.
Use a pressure line with a
larger diameter.
The pressure line
is blocked.
Remove the blockage.
The suction opening
is blocked.
Remove the blockage.
The pressure line is kinked. Straighten the
pressure line.
The pressure line leaks. Seal the pressure
line, tighten the
threaded connections.
The pump runs
very loudly.
The pump is drawing in air. Ensure there is sufficient
liquid present.
Keep the pump at an
angle while submerging.
Visit www.princessauto.com for more information 13

V4,0 8645830
Manuel d'utilisateur
Pompedepuissard
de1/3CV
Vous devez lire et comprendre toutes les instructions avant d'utiliser l'appareil.
Conservez ce manuel afin de pouvoir le consulter plus tard.

8645830 Pompe de puissard de 1/3 CV V4,0
SPÉCIFICATIONS
Débit max. 3 036 gal/h
Puissance 1/3 CV
Tension nominale 115 V
Courant nominal 3,9 A
Orifices d’entrée / de sortie 1 & 1 1/4 po
Hauteur d’aspiration max. 23 pi
Hauteur de refoulement max. 20 pi
Matériau du boîtier Aluminium coulé
Matériau d’impulseur Plastique
Débit à 5 pi 2 376 gal/h
Débit à 10 pi 1 769 gal/h
Débit à 15 pi 1 161 gal/h
Débit à 20 pi 132 gal/h
Interrupteur à flotteur
Avec cable de retenue
Longeur du cordon 3,05 m (10 pi)
Application(s) Jardinage
UL/CUL UL/CUL#E248578
Pompedepuissard
de1/3CV
2 En cas de questions techniques, appelez le 1-800-665-8685

V4,0 Pompe de puissard de 1/3 CV 8645830
SÉCURITÉ
AVERTISSEMENT ! Veuillez lire et comprendre toutes les instructions avant d'utiliser
cet outil. L'utilisateur doit respecter les précautions de base lorsqu'il utilise cet
outil afin de réduire le risque de blessure ou de dommage à l'équipement.
CONSERVER CES INSTRUCTIONS
Conservez ce manuel qui contient les avertissements de sécurité, les précautions, les
instructions de fonctionnement ou d'inspection et d'entretien.
DÉFINITIONS DE DANGER
Veuillez-vous familiariser avec les avis de danger qui sont présentés dans ce manuel.
Un avis est une alerte indiquant qu'il existe un risque de dommage à la propriété, de
blessure ou de décès si on ne respecte pas certaines instructions.
DANGER ! Cet avis indique un risque immédiat et particulier qui entraînera
des blessures corporelles graves ou même la mort si on omet
de prendre les précautions nécessaires.
AVERTISSEMENT ! Cet avis indique un risque particulier ou une pratique non
sécuritaire qui pourrait entraîner des blessures corporelles
graves ou même la mort si on omet de prendre les
précautions nécessaires.
ATTENTION ! Cet avis indique une situation possiblement dangereuse qui peut
entraîner des blessures mineures ou modérées si on ne procède
pas de la façon recommandée.
AVIS ! Cet avis indique un risque particulier ou une pratique non
sécuritaire qui entraînera des dommages au niveau de
l'équipement ou des biens, mais non des blessures corporelles.
AIRE DE TRAVAIL
1. Travaillez dans un environnement de travail sécuritaire. Gardez votre aire de travail
propre, bien éclairée et exempte de toute distraction.
2. Assurez-vous que les personnes qui ne portent pas l'équipement de sécurité
approprié ne se trouvent pas à proximité de l'aire de travail.
3. Rangez les outils correctement dans un lieu sécurisé et sec. Gardez les outils hors
de la portée des enfants.
4. N'installez pas et n'utilisez pas d'outils électriques en présence de gaz, de
poussière ou de liquides inflammables.
Visitez www.princessauto.com pour plus d'informations 3

8645830 Pompe de puissard de 1/3 CV V4,0
SÉCURITÉ PERSONNELLE
AVERTISSEMENT ! Portez de l'équipement de protection personnelle homologué
par l'Association canadienne de normalisation (CSA) ou l'American National
Standards Institute (ANSI).
ÉQUIPEMENT DE PROTECTION PERSONNELLE
1. Portez toujours des lunettes antiprojections qui offrent une protection frontale et
latérale pour les yeux. L'équipement de protection des yeux devrait être conforme
à la norme CSA Z94.3-07 ou ANSI Z87.1 fonction du type de travail effectué.
2. Portez des gants qui protègent en fonction des matériaux de travail et pour réduire
les effets des vibrations de l'outil.
3. Portez des vêtements de protection conçus pour l'environnement de travail et
pour l'outil.
4. Les chaussures antidérapantes sont recommandées pour maintenir la stabilité et
l'équilibre au sein de l'environnement de travail.
5. Portez des chaussures à embout d'acier ou à coquilles d'acier pour éviter les
blessures aux pieds dues à la chute d'objets.
6. Portez un appareil respiratoire approuvé par la NIOSH pour travailler sur des
matériaux qui produisent des émanations dangereuses, de la poussière ou
des particules.
PRÉCAUTIONS PERSONNELLES
Gardez le contrôle de l'outil, de vos mouvements et de l'environnement de travail pour
éviter les blessures ou le bris de l'outil.
1. N'utilisez pas l'outil si vous êtes fatigué ou sous l'effet de drogues, d'alcool ou
de médicaments.
2. Évitez de porter des vêtements ou des bijoux pouvant se prendre dans les pièces
mobiles d'un outil. Gardez les cheveux longs recouverts ou attachés.
3. N'utilisez pas l'outil si vous devez étirer les bras pour vous en servir. Une stabilité
et un équilibre appropriés sont nécessaires afin d'avoir un meilleur contrôle en cas
de situations inattendues.
4 En cas de questions techniques, appelez le 1-800-665-8685

V4,0 Pompe de puissard de 1/3 CV 8645830
CONSIGNES DE SÉCURITÉ SPÉCIFIQUES
DANGER ! Ne permettez PAS au confort ou à votre familiarisation avec l'outil
(obtenus après un emploi répété) de se substituer à une adhésion stricte aux règles
de sécurité de l'outil. Si vous utilisez cet outil de façon dangereuse ou incorrecte,
vous pouvez subir des blessures corporelles graves.
1. Utilisez le bon outil pour la tâche à effectuer. Cet outil a été conçu pour une utilisation
spécifique. Évitez de modifier ou d'altérer cet outil ou de l'utiliser à une fin autre que
celle pour laquelle il a été conçu.
2. Portez des lunettes de sécurité lorsque vous travaillez sur les pompes.
3. Ne faites pas fonctionner la pompe s'il n'y a pas d'eau dans le système.
4. N'utilisez pas les pompes dans une eau dont la température est supérieure à
40 °C (104 °F). Évitez de vider les réservoirs d'eau chaude dans les puisards.
5. N'alimentez pas cet appareil avec toute source d'énergie autre qu'une alimentation
de 120 V.
6. Reliez ce produit à un circuit à la masse muni d'un dispositif de disjoncteur de
fuite à la terre (GFCI).
7. N'installez pas la pompe dans un endroit qualifié de dangereux dans le Code
électrique national, dans la norme ANSI/NFPA 80-1984 ou dans le Code canadien
de l'électricité.
8. N'utilisez pas les pompes afin de pomper de la boue, du sable, du ciment, des
graisses, du sel, les eaux usées des toilettes, des huiles, des substances
combustibles ou explosives ou des produits chimiques.
9. L'appareil a pour but de pomper l'eau de pluie, l'eau douce, l'eau de conduite
principale ainsi que l'eau de piscine chlorée.
10. La pompe ne doit pas être utilisée pour pomper de l'eau potable ou pour
acheminer des produits alimentaires.
11. L'appareil ne convient pas à un usage industriel ou commercial.
12. La pompe ne peut pas fonctionner de manière continue (par exemple, pour
entretenir une circulation permanente dans les systèmes de filtration).
13. Risque d'incendie ou d'explosion. Ne pompez pas des liquides inflammables ou
explosifs comme l'essence, le carburant, l'huile, le kérosène, etc.
14. N'utilisez pas dans un environnement inflammable et/ou explosif.
15. Avant d'installer ce produit, faites vérifier le circuit électrique par un électricien afin
d'assurer une mise à la masse efficace.
Visitez www.princessauto.com pour plus d'informations 5

8645830 Pompe de puissard de 1/3 CV V4,0
16. Ne soulevez pas la pompe au moyen du cordon d'alimentation.
17. Assurez-vous que la source d'énergie de la pompe est déconnectée avant
d'installer ou d'entretenir la pompe.
18. Vérifiez la tension sur la plaque signalétique du moteur et assurez-vous que la
tension de ligne de l'alimentation en courant est identique.
19. N'exposez pas la pompe aux températures de congélation. Le gel pourrait causer
des dommages graves, ce qui annulera la garantie.
20. N'introduisez pas de doigt ou d'objet dans les orifices de la pompe ou du moteur.
21. Ne faites pas fonctionner la pompe à sec. Un fonctionnement à sec peut faire
surchauffer la pompe (entraînant ainsi des blessures à quiconque tente de la
manipuler), ce qui aura pour effet d'annuler la garantie.
22. La pompe est normalement chaude lorsqu'elle est en marche. Pour éviter les
brûlures lors de l'entretien de la pompe, laissez-la refroidir pendant 20 minutes
après l'arrêt avant sa manutention.
23. Vérifiez toujours la pompe avant chaque utilisation. Évitez d'utiliser la pompe
si elle est endommagée. Confiez l'entretien de la pompe à un technicien de
service qualifié.
SÉCURITÉ EN ÉLECTRICITÉ
AVERTISSEMENT ! Les tensions dangereuses peuvent électrocuter, brûler ou causer
la mort. Lors de l'installation, de l'utilisation ou de l'entretien de cette pompe,
observez les instructions de sécurité énoncées ci-dessous.
1. Évitez que la fiche à l'extrémité du cordon d'alimentation ne soit submergée.
2. N'utilisez pas de rallonges de câble. Ils constituent un risque d'incendie et
peuvent réduire la tension suffisamment pour empêcher le pompage ou
endommager le moteur.
3. Ne tentez pas de manipuler ou d'entretenir la pompe alors qu'elle est reliée à une
source d'énergie.
4. Placez le moteur à la masse avant de le brancher à une source d'énergie.
5. À défaut de mettre le moteur à la masse, il peut en résulter un choc électrique
grave ou même fatal.
6. Ne mettez pas le moteur à la masse en le connectant à une conduite d'alimentation
de gaz.
7. Pour éviter un choc électrique dangereux ou fatal, coupez l'alimentation au niveau
du moteur avant de travailler sur les connexions électriques.
6 En cas de questions techniques, appelez le 1-800-665-8685