TE HTP600 User manual

412-121040
USER GUIDE /// ENTRELEC TERMINAL BLOCKS - HTP600 THERMAL TRANSFER PRINTER /// 412-121040 REV 1
HTP600 Thermal Transfer Printer and Markers
USER GUIDE
English Version
This User guide is dedicated to the installation and start-up of the Thermal Transfer
Marking System HTP600 that is composed of the Thermal transfer printer and
accessories.
Windows® is a registered trademark of Microsoft Corporation in the United States and other countries.
THIS IS A CLASS 1 DOCUMENT WHICH IS NONCONFIDENTIAL.
The information contained within this document is the property of TE Connectivity. It is supplied in
confidence and the commercial security of the contents must be maintained. It must not be used for any
purpose other than that for which it is supplied nor may any information contained in it be disclosed to
unauthorised persons. It must not be reproduced in whole or in part without obtaining written permission
from TE Connectivity (TE).
While TE has made every reasonable effort to ensure the accuracy of the information in this catalog, TE does not guarantee that it is error-free, nor does TE make any
other representation, warranty or guarantee that the information is accurate, correct, reliable or current. TE reserves the right to make any adjustments to the information
contained herein at any time without notice. TE expressly disclaims all implied warranties regarding the information contained herein, including, but not limited to, any
implied warranties of merchantability or fitness for a particular purpose. The dimensions in this catalog are for reference purposes only and are subject to change without
notice. Specifications are subject to change without notice. Consult TE for the latest dimensions and design specifications.
*Trademark. TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product and/or company names may be trademarks of their respective owners.

USER GUIDE /// ENTRELEC TERMINAL BLOCKS - HTP600 THERMAL TRANSFER PRINTER /// 412-121040 REV 1
2
SUMMARY
USER GUIDE ......................................................................................................................................1
INTRODUCTION .................................................................................................................................4
BEFORE USE ............................................................................................................. 10
ACCESSORIES ......................................................................................................................................10
IDENTIFICATION OF THE PRINTER PARTS........................................................................................11
IMPORTANT SAFETY INFORMATION ..................................................................................................13
Printer Setup Location ........................................................................................................................................ 13
Power Supply ...................................................................................................................................................... 15
External Cleaning of the Printer .......................................................................................................................... 15
Use and Maintenance ......................................................................................................................................... 15
Precaution while moving the Printer .................................................................................................................... 16
Recommended Environmental Conditions .......................................................................................................... 16
PRINTER FEATURES ............................................................................................................................17
PREPARATION OF HTP600 FOR PRINTING............................................................. 18
CONTROL PANEL AND ITS FUNCTIONS .............................................................................................19
Control Panel Menu mode .................................................................................................................................. 20
Data receiving Display Messages ....................................................................................................................... 20
POWER SUPPLY CABLE CONNECTION .............................................................................................21
USB CABLE CONNECTION ...................................................................................................................21
LOADING / REMOVING THE CLEANING CASSETTE ..........................................................................22
Loading of the Cleaning Cassette ....................................................................................................................... 22
Removing the Cleaning cassette ........................................................................................................................ 24
LOADING A RIBBON CASSETTE ..........................................................................................................25
TURNING THE POWER ON / OFF ........................................................................................................26
Turning the Power On ......................................................................................................................................... 26
Turning the Power Off ......................................................................................................................................... 26
REMOVING A PLATE .............................................................................................................................27
DRIVER AND SOFTWARE INSTALLATION .............................................................. 28
STEP BY STEP INSTRUCTIONS FOR THE HTP600 DRIVER SETUP ................................................28
STEP BY STEP INSTRUCTIONS FOR THE CREATION OF THE 7 HTP600 PRINTER DEVICES .....31
STEP BY STEP INSTRUCTIONS FOR THE HTS600 SOFTWARE SETUP .........................................32
STEP BY STEP INSTRUCTIONS FOR THE HTS600 SOFTWARE ACTIVATION ...............................33
STEP BY STEP INSTRUCTIONS FOR SETTING THE 7 HTP600 PRINTER DEVICES IN HTS600 ...35
PRINTING CENTERING .........................................................................................................................43
PRINTING CALIBRATION LENGTH ......................................................................................................45
PRINTER DRIVER UNINSTALL .............................................................................................................46
PRINTER DRIVERS SELECTION ..........................................................................................................47
PRINTING TAGS WITH AUTOMATIC FEEDER IN “STACK” Feeder Mode ............. 48
FEEDER ACCESSORIES .......................................................................................................................48
PREPARING OF THE CARD STORE ....................................................................................................49
PREPARING OF THE SUPPORT PLATE ..............................................................................................50
TURNING ON THE PRINTER.................................................................................................................52
PRINT ON CABLE TAGS........................................................................................................................52
PRINTING TERMINAL BLOCK MARKERS IN “SINGLE” Mode ................................ 53
ACCESSORIES ......................................................................................................................................53
SUPPORT PLATE PREPARATION ........................................................................................................53
TURN ON THE PRINTER .......................................................................................................................55
PRINT ON TERMINAL BLOCK MARKERS CARDS ..............................................................................55
PRINTS OF TAGS MANUALLY WITHOUT SUPPORT PLATES ................................ 56
PRINTER PREPARATION ......................................................................................................................56
MODULES INSERTION INTO THE PRINTER .......................................................................................57
TURN ON THE PRINTER .......................................................................................................................58
PRINTING TAGS AND STRIPS ..............................................................................................................58

USER GUIDE /// ENTRELEC TERMINAL BLOCKS - HTP600 THERMAL TRANSFER PRINTER /// 412-121040 REV 1
3
MAINTENANCE .......................................................................................................... 59
USEFUL FUNCTIONS ............................................................................................................................59
TROUBLE SHOOTING ...........................................................................................................................60
PRINTER MESSAGES / ERRORS .........................................................................................................62
WRITING PROBLEMS ........................................................................................................................................ 62
NOTIFICATION MESSAGES .............................................................................................................................. 63
FAILURE MESSAGES ........................................................................................................................................ 63
DAILY CARE ...........................................................................................................................................64
CLEANING OF THE CLEANING ROLLER ......................................................................................................... 64
OTHER PARTS TO CLEAN ................................................................................................................................ 65
SPARE PARTS ................................................................................................................................................... 65
CLEANING AND STORING PLATES .....................................................................................................66
TEST PRINT ...........................................................................................................................................66
CORRECT USE OF THE SYSTEM ........................................................................................................66
SUMMARY CHART OF MODULES, SUPPORT PLATES AND ACCESSORIES OF
HTP600 SYSTEM .............................................................................................................................. 67
INFORMATION TO USERS ON RECYCLING OPERATIONS .................................... 68
TE TECHNICAL ASSISTANCE ................................................................................. 69

USER GUIDE /// ENTRELEC TERMINAL BLOCKS - HTP600 THERMAL TRANSFER PRINTER /// 412-121040 REV 1
4
INTRODUCTION
Thank you for choosing HTP600!
HTP600 printer will help you print fast and easy.
To ensure HTP600 best performances, read this manual thoroughly before use.
Make sure to follow very carefully the instructions given in this manual, in particular the ones
described below:
WARNING
Indicates situations where mishandling might result in serious injury or even death. For your
own safety, always observe these warnings
CAUTION
Indicates situations where mishandling might result in personal injury or damage to property. To
protect yourself and your property, be sure to observe these cautions
NOTICE
Indicates important information and restrictions concerning operation. Be sure to read this
information to prevent the unit from breaking down or being damaged, and to ensure it is
not operated incorrectly
REMIND
Indicates supplementary information and instructions
This manual uses shortened product names as shown below:
Full product name: Shortened product name:
Microsoft® Windows® XP Windows® XP
Microsoft® Windows® Vista Windows® Vista
Microsoft® Windows® 7 Windows® 7
Microsoft® Windows® 8 Windows® 8
Microsoft® Windows® 8.1 Windows® 8.1
Microsoft® Windows® 10 Windows® 10
Windows® is a registered trademark of Microsoft Corporation in the United States and other countries.

USER GUIDE /// ENTRELEC TERMINAL BLOCKS - HTP600 THERMAL TRANSFER PRINTER /// 412-121040 REV 1
5
HTP600 Printer
Environmental Information
To reduce the risks associated with environmental contamination, which if not avoided, may result in
minor or moderate injury and / or property damage:
Do not throw the product away into the normal domestic waste. Dispose device at end of life in accordance with
national and/or local regulations.
Explanation of shown symbols or labels
Alert
symbol
Hot
surface
WEEE
CE
Mark
Important safety instruction
Keep this manual for future reference!
This document will support you during the use of the HTP600 Printer. Please read the
warnings carefully and use the product as described in this instruction to avoid accidental
injury or damage.
Explanation of Signal Word Consequences
WARNING
Indicates a potentially hazardous situation, which, if not avoided, could result
in death or serious injury and/or property damage.
CAUTION
Indicates a potentially hazardous situation, which, if not avoided, may result
in minor or moderate injury and/or property damage.
NOTICE
Indicates a property damage message
General information
Thermal Transfer Marking
System PR
-
P101
Is conform to the following pertinent regulations:
2011/65/EU
2014/35/EU
2014/30/EU
Year in which CE Mark first affixed: 2018 Applied standards and
technical specifications:
CSA and UL listed
Tested to comply to FCC Standard for home and office
Intended use:
The HTP600 Printer is approved only for the use in closed rooms and a dry environment.

USER GUIDE /// ENTRELEC TERMINAL BLOCKS - HTP600 THERMAL TRANSFER PRINTER /// 412-121040 REV 1
6

USER GUIDE /// ENTRELEC TERMINAL BLOCKS - HTP600 THERMAL TRANSFER PRINTER /// 412-121040 REV 1
7

USER GUIDE /// ENTRELEC TERMINAL BLOCKS - HTP600 THERMAL TRANSFER PRINTER /// 412-121040 REV 1
8
FCC (Federal Communications Commission)
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
 Reorient or relocate the receiving antenna.
 Increase the separation between the equipment and receiver.
 Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
 Consult the dealer or an experienced radio/TV technician for help.
Use of shielded cable is required to comply with class B limits in Subpart B of Part 15 of FCC
Rules.
Do not make any change or modifications to the equipment unless otherwise specified in the
manual. If such changes or modifications should be made, you could be required to stop
operation of the equipment.
Users in the U.S.A.

USER GUIDE /// ENTRELEC TERMINAL BLOCKS - HTP600 THERMAL TRANSFER PRINTER /// 412-121040 REV 1
9
HTP600 Printer
WARNING
To reduce the risks associated with short circuit, fire and/or electrical shock, which if not avoided, could
result in minor or moderate injury:
•
Don’t set this printer up close to alcohol, paint thinner and other flammable chemicals.
•
Don’t use flammable sprays close to the printer.
•
When cleaning the printer, dampen some gauze and wash it out thoroughly. Do not use flammable solvents,
such as alcohol, benzene or paint thinner.
•
If the printer is not working properly, emitting smoke or strange smells, turn it off immediately, unplug the power
cord and contact the TE Technical Assistance.
•
Don’t use multi socket adapters to plug more than one device into one single plug.
•
Make sure that the power cord is properly plugged in.
•
Never attempt to disassemble or modify the printer.
•
Before cleaning the printer, always turn it off and unplug the power cord.
•
Do not connect the printer to a power source that provides other than the rated voltage (100V to 240 AC, 50/60
Hz). Using any other voltage could cause a fire or electric shock.
•
Do not pull the power cord when it is connected to the power cord socket on the rear of the printer or otherwise
apply undue force to the power cord connector. Doing so could damage the wiring and cause a short, fire, or
electric shock.
•
When unplugging the power cord from the power outlet or the socket on the rear of the printer, always grasp the plug
or connector.
Failure to follow the warnings and cautions describe below during use and maintenance of the printer
could result in accidents, fire, electrical shock or burns:
•
Do not touch the print head immediately after printing.
•
Do not use this printer and its accessories for any purpose other than the one designed to.
•
Do not scratch the print head.
•
Do not clean the print head using cloths that have metallic particles adhering to them. If the print head is
scratched it cannot print in the scratch zone.
•
When cleaning the print head be
careful.
CAUTION
To reduce the risks associated with short circuit, fire and/or electrical shock, which if not avoided, may
result in minor or moderate injury:
•
Do not place heavy objects, metallic objects or containers of liquids on the printer.
•
Do not set up the printer on an unstable surface or in a location subject to vibrations.
•
Do not set up the printer in a hot, humid or dusty location, nor in the vicinity of an open flame.
•
Do not set up the printer on a rug or a carpet?????
•
Keep the area around the power plug free of obstructions so that you can unplug the power cord at any time.
•
Do not cover the fan holes.
•
Keep the area around the printer free as shown in the picture on page 14.
Failure to follow the warnings and cautions describe below during use and maintenance of the printer could
result in accidents, fire, electrical shock or burns:
•
Use only the ribbon cassette on equipment. Never attempt to disassemble the ribbon cassette or place another
ribbon inside the cassette. Do not pull the plate or sheet while print is being in process
•
Do not expose HTP600 to direct sunlight, high humidity or dust. Use and store the printer and its accessories
respecting the environmental conditions listed below:
Temperature °C Humidity RH
Operative environment 15 - 32.5 15 - 80
Storage environment 5 - 35 35 - 85
•
During the printing process never open the cassette cover and never touch the cleaning auxiliary roller or the
conveyor roller.
•
Never use the printer without the cleaning cassette. Using the printer when the cleaning roller is dirty can damage the
print head.
•
Before loading the cleaning cassette, take out the ribbon cassette. Trying to load the cleaning cassette while the
ribbon cassette is still in place could cause the cleaning cassette to be loaded incorrectly.
•
After loading the cleaning cassette, make sure that the guide tabs are securely fixed in the notches of the cassette.
•
Do not turn off the printer while it is printing to avoid damaging the print head or the
ribbon.

USER GUIDE /// ENTRELEC TERMINAL BLOCKS - HTP600 THERMAL TRANSFER PRINTER /// 412-121040 REV 1
10
BEFORE USE
Chapter 1 contains four sections as follows:
1.1 Accessories
1.2 Identification of Printer Parts
1.3 Important Safety Information
1.4 Printer Features
ACCESSORIES
The HTP600 has the following accessories:
Ribbon cassette Cleaning cassette Cleaning roller
The software download file contains:
 HTS600 Software
 HTP600 Printer Driver
 User guide

USER GUIDE /// ENTRELEC TERMINAL BLOCKS - HTP600 THERMAL TRANSFER PRINTER /// 412-121040 REV 1
11
IDENTIFICATION OF THE PRINTER PARTS
Printer Front Part
Inside details front part of the Printer

USER GUIDE /// ENTRELEC TERMINAL BLOCKS - HTP600 THERMAL TRANSFER PRINTER /// 412-121040 REV 1
12
Back Part of the Printer
At the back of the printer is the CE Mark label that contains:
 Year of construction
 Attesting that the product conforms to EU rules
At the front is a label showing the serial number and TE’s address

USER GUIDE /// ENTRELEC TERMINAL BLOCKS - HTP600 THERMAL TRANSFER PRINTER /// 412-121040 REV 1
13
IMPORTANT SAFETY INFORMATION
Always observe the following warnings and cautions for a safe and correct use of HTP600.
Printer Setup Location
The Printer is suitable to be used in an internal environmental, in absence of dust or liquid
substances.
The Printer is not suitable to be used in external places and should not be exposed to weathering.
The Printer cannot be used in places where it may be in danger of explosion because it is not suitable
to be used in an explosive atmosphere (the electrical equipment is not compliant with regards to the
risk of explosion, to the actual norm in force).
Place the HTP600 Printer in a suitable environmental in which the following precaution are observed:
Follow all described instructions with the printer turned off.
2) Install the printer HTP600 on the Base as shown in the picture.
3) Open the Right support for inserting the Items in the Printer.
CAUTION
 Don’t place heavy objects on the printer
 Don’t place metallic objects or containers of liquids on the printer
 Don’t set up the printer on an unstable surface or in a location subject to vibrations
 Don’t set up the printer in a hot, humid or dusty location, nor in the vicinity of an open flame
 Don’t set up the printer on a rug or a carpet
 Keep the area around the power plug free of obstructions so that you can unplug the power
cord at any time
 Don’t cover the fan holes

USER GUIDE /// ENTRELEC TERMINAL BLOCKS - HTP600 THERMAL TRANSFER PRINTER /// 412-121040 REV 1
14
Keep the area around the printer free as shown in the picture below
WARNING
 Don’t set this printer up close to alcohol, paint thinner and other flammable chemicals
 Don’t use flammable sprays close to the printer

USER GUIDE /// ENTRELEC TERMINAL BLOCKS - HTP600 THERMAL TRANSFER PRINTER /// 412-121040 REV 1
15
Power Supply
Remember every electrical equipment can cause injury if not handled properly.
Make sure you observe the following warnings and cautions to prevent accidents and injuries.
WARNING
 If the printer begins working not properly, emitting smoke or strange smells, turn it off
immediately, unplug the power cord and contact TE Technical Assistance
 Never handle the power cord with wet hands
 Don’t use multi socket adapters to plug more than one device into one single plug
 Make sure that the power cord is properly plugged in
 Don’t put the power cord close to a heat source
 Never attempt to disassemble or modify the printer
 Before cleaning the printer, always turn it off and unplug the power cord
 When cleaning the printer, dampen some gauze and wash it out thoroughly. Do not use
flammable solvents, such as alcohol, benzene or paint thinner.
External Cleaning of the Printer
Always clean the printer when it is turned off and not plugged to Power. Use a dry cloth or a little wet
with water. Do not use flammable liquids.
Use and Maintenance
Failure to follow the warnings and cautions described below during use and maintenance of the
printer could result in accidents, fire, electrical shock or burns.
WARNING
 Don’t touch the print head immediately after printing
 Don’t use this printer and its accessories for any purpose other than the one designed for
CAUTION
 Use only the ribbon cassette on equipment. Never attempt to disassemble the ribbon
cassette to place another ribbon inside the cassette
 Do not pull the plate or sheet while print is in progress
 Do not expose HTP600 to direct sunlight, high humidity or dust. Use and store the printer and
its accessories respecting the environmental conditions listed below:
WARNING
 Don’t connect the printer to a power source that provides other than the rated voltage:
100÷240 V AC, 50/60Hz
 If some foreign material (a piece of metal, some water or some other liquid) gets inside the
printer, turn the power off immediately, unplug the power cord and contact TE Technical
Assistance
 While unplugging the power cord, always grasp the plug, not the cord. Pulling the cord could
damage it
 If the printer is not going to be used for a long time, unplug the power cord. If the cord is not
unplugged, that could result in an electrical leak.
 It is always a good habit not to leave the cord plugged in for long periods of time anyway.

USER GUIDE /// ENTRELEC TERMINAL BLOCKS - HTP600 THERMAL TRANSFER PRINTER /// 412-121040 REV 1
16
Precaution while moving the Printer
Before moving the printer or while using and maintaining the HTP600, always observe the precaution
below to prevent risks of fire, electric shock or burns. (Always observe local safety rules)
 The printer weight is 9.5 kg.
 Lift the printer with two hands.
 Keep the printer near the body while you are moving it.
 Before moving the printer, locate a suitable flat surface.
 Make sure that all the printer parts can be rotated and / or moved (eg. cover of the
head protection) are fixed and / or locked properly.
 Ensure all connections to the printer are disconnected.
 Check the space available along each side of the printer, complies with the
dimensions, shown on page 14.
 Check the power supply compatibility. into the destination place
 Hold the printer firmly.
 Do not carry the printer using the cover.
Recommended Environmental Conditions
Utilize HTP600 in the following environmental conditions:
Temperature °C Humidity % RH
Operating environment 15 to 32.5 15 to 80
Storage environment 5 to 35 35 to 85
When gentle opening and closing the cassette cover or tray, be careful not to catch your fingers.
WARNING
Do not touch the cassette cover and the rollers during the printing phase

USER GUIDE /// ENTRELEC TERMINAL BLOCKS - HTP600 THERMAL TRANSFER PRINTER /// 412-121040 REV 1
17
PRINTER FEATURES
This chapter describes the Main features of the printer HTP600.
Print method
Thermal transfer print.
Resolution
300dpi.
Print speed
Plate: 30 mm/sec, manual mode: 20 mm/sec, Automatic: 20 mm/sec.
Guaranteed print area
Width 54 mm; length 496 mm
Ribbon cartridges
Black Ribbon length: 130 MT
Colours available: Black, Red, Green & Blue
Operating environment
Temperature: 15 to 32.5 °C
RH: 15 to 80 % without condensation
Interfaces
Standard Centronics interface, USB 2.0
Power supply
100 to 240V AC, 50/60Hz
Power consumption
45 W
Dimensions
Width 418 mm, Depth 235 mm, Height 210 mm
Weight
9.5 Kg
Supported consumable materials
Only items supplied and tested for HTP600 by TE can be used.

USER GUIDE /// ENTRELEC TERMINAL BLOCKS - HTP600 THERMAL TRANSFER PRINTER /// 412-121040 REV 1
18
PREPARATION OF HTP600 FOR PRINTING
This chapter describes how to get HTP600 ready to print.
2.1 Control Panel Components and its Functions
❑
LEDS
❑
KEYS
❑
DISPLAY
2.1.1 Control Panel Menu Mode
2.1.2 Data Receiving Display Messages
2.2 Connecting the Power Cord
2.3 Connecting the USB Interface Cable
2.4 Loading / Removing of Cleaning Cassette
2.1.3 Loading
2.1.4 Removing
2.5 Loading of Ribbon Cassette
2.6 Turning the power On/Off
2.1.5 Turning the Power On
2.1.6 Turning the Power Off
2.7 Loading a Plate
2.8 Removing a Plate

USER GUIDE /// ENTRELEC TERMINAL BLOCKS - HTP600 THERMAL TRANSFER PRINTER /// 412-121040 REV 1
19
CONTROL PANEL AND ITS FUNCTIONS
❑
LEDS
POWER: Lights, when you turn on the power switch is switched on.
ONLINE: Lights, when the printer is ready to receive data and flashes when the printer is
receiving data. Turns off when the printer is offline.
MESSAGE: Flashes when an error has occurred, and the printer is not able to print.
❑
KEYS
[ONLINE]: Press this key to switch the printer online
[MENU/]: Press this key to enter the printer Menu selection mode when the printer is
offline. Once entering the Menu mode, use this key to select the Menu function
desired.
If the Menu function has been selected, holding down this key will cause the
conveyor roller to rotate to the left ejecting the item inserted in the printer.
[]: Once entered the Menu mode, use this key to display each Menu function.
If the Menu function has been selected, holding down this key will cause the
conveyor roller to rotate to the right ejecting the item inserted into the printer.
[ENTER]: Press this key to confirm and execute the Menu function selected.
[CANCEL]: Press this key to cancel the Menu function selected.
Press this key to eject an item inserted in the printer.
Hold down this key for at least 3 seconds straight, to cancel the data received
from the printer.
REMIND
In order to perform a Menu function, always put the printer offline pressing the ONLINE key so
that the ONLINE LED turns off.
LCD screen
HTP600 screen shows the printer functions and statuses.

USER GUIDE /// ENTRELEC TERMINAL BLOCKS - HTP600 THERMAL TRANSFER PRINTER /// 412-121040 REV 1
20
Control Panel Menu mode
Turn on HTP600 printer.
The two following messages will appear on the display:
Press the ONLINE button to put the printer OFFLINE (the ONLINE led turns off).
At this stage each one of the following Menu functions can be selected:
CLEANING to clean the cleaning roller.
BACKLIGHT to set the contrast of light of the LCD Panel.
LANGUAGE to select the Language of the printer LCD menu.
AUTO OFF to set the time the Printer will turn off after a period of Non-Use.
PRINT MODE to set the print mode to “speed”.
AUTO CLEANING to set the distance for the automatic cleaning of the cleaning roller.
REMOVE to clear a jam or to eject a printer media.
Always use the [MENU/] and [] keys, located on the control panel, to select the printer Menu
functions and then press ENTER and CANCEL to confirm or cancel the execution of a function.
Data receiving Display Messages
REMIND
The function data check can be set from the driver:
The LCD display will visualize the following messages: these are the parameters the printer
receives.
K V 1 Manu K m 1 Stack K V 1 Sing
3 60mm 500mm 1 60mm 150mm 3 60mm 150mm
PLATE PRINTER
Version 2.01
Ready
Plate
Printing
S
-
black