Teac BU-LX1000 User manual

Z
BU-LX1000
Battery unit
Instructions for Use
Introduction
Thank you for purchasing the BU-LX1000 battery unit. Please read this document
in its entirety before using the product to get the best performance and ensure
safe and proper operation.
Included accessories
Connection screws (flathead M3 × 5) × 4
Instructions for Use (this document) × 1
IMPORTANT SAFETY INSTRUCTIONS
Model for USA
Supplier’s Declaration of Conformity
Model number: BU-LX1000
Trade name: TEAC
Responsible party: TEAC AMERICA,INC.
Address: 10410 Pioneer Blvd. Suite #1, Santa Fe Springs, California 90670, U.S.A.
Telephone number: [phone]
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
Information
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be required to correct the
interference at his own expense.
CAUTION
Changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
Model for Canada
Industry Canada’s Compliance Statement: This Class A digital apparatus complies with
Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.
Model for Europe
This product complies with the European Directives request, and the other
Commission Regulations.
Disposal of electrical and electronic equipment
(a) All electrical/electronic equipment should be disposed of separately from the municipal
waste stream via collection facilities designated by the government or local authorities.
(b) By disposing of electrical/electronic equipment correctly, you will help save valuable
resources and prevent any potential negative effects on human health and the environment.
(c) Improper disposal of waste electrical/electronic equipment can have serious effects
on the environment and human health because of the presence of hazardous sub-
stances in the equipment.
(d) The Waste Electrical and Electronic Equipment (WEEE) symbols, which show
wheeled bins that have been crossed out, indicate that electrical/electronic
equipment must be collected and disposed of separately from household waste.
(e) Return and collection systems are available to end users. For more detailed infor-
mation about the disposal of old electrical/electronic equipment and waste
batteries/accumulators, please contact your city office, waste disposal service or the
shop where you purchased the equipment.
WARNING
This is a Class A product. In a domestic environment, this product may cause radio inter-
ference in which case the user may be required to take adequate measures.
ATENCIÓN
Este es un producto de clase A. En un entorno no profesional, este aparato puede producir
interferencias de radio, en cuyo caso el usuario será el responsable de tomar las medidas
necesarias para solucionarlo.
AVERTISSEMENT
Il s’agit d’un produit de Classe A. Dans un environnement domestique, cet appareil peut
provoquer des interférences radio, dans ce cas l’utilisateur peut être amené à prendre des
mesures appropriées.
Warnung
Dies ist eine Einrichtung, welche die Funk-Entstörung nach Klasse A besitzt. Diese Einrichtung
kann im Wohnbereich Funkstörungen verursachen; in diesem Fall kann vom Betreiber ver-
langt werden, angemessene Maßnahmen durchzuführen und dafür aufzukommen.
Precautions for use
oDo not use any battery other than the NP-L7S made by IDX Company, Ltd.
oIncorrect battery handling could cause rupture, fire, smoke, heat or fluid leak-
age and could lead to reduced performance or malfunction. Always abide by
the prohibitions in the battery owner’s manual.
oBatteries (including products that contain them) should not be exposed to
sunshine, fire or excessive heat.
oDo not connect the output cable of this unit to its DC IN connector when
batteries are installed. Doing so might reduce performance or cause a
malfunction.
oBefore changing the batteries, turn the LX-1000 off. Furthermore, if a power
cord is connected to the DC IN connector, disconnect it.
oAlways use batteries in sets of three.
oCharge the batteries completely using the following battery charger before use.
IDX JL-2PLUS
oAlways remove batteries before disposing of this product. To dispose of a
removed battery, follow the instructions in its manual.
oAlways remove the batteries before transporting this product.
oThis product is designed specifically for the LX-1000. Do not use it with any
other product.
Assembly procedures
1 Remove the rubber feet from the LX-1000 unit.
Keep the removed rubber feet and screws.
Rubber feet
2 Use screws to attach the LX-1000 unit and the BU-LX1000
battery unit(s).
Use the included connection screws to attach them at the joints (in
4locations).
Tighten the screws with a torque of 60N·cm (6kgf·cm).
3 Attach the rubber feet removed from the LX-1000 unit to the
bottom of the BU-LX1000 battery unit.
Tighten the screws with a torque of 60N·cm (6kgf·cm).
D01350010A

Connecting cables
When using the main unit (LX-1000) alone or with a single expansion unit
(AU-LX1000EPIO), they can be powered with a single battery unit (BU-LX1000).
When using two or three expansion units, two battery units are necessary.
Connect battery units and, if using them, AC adapters (included with the
LX-1000) as shown in the following illustrations.
16-channel and 32-channel models
AC adapter (included
with LX-1000)
48-channel and 64-channel models
AC adapter (included
with LX-1000)
AC adapter (included
with LX-1000)
Using with an external power supply
Power can be supplied to the LX-1000 by connecting AC adapters included with
the LX-1000 to the DC IN connectors of BU-LX1000 units.
The LX-1000 unit operates on 8V–36V DC.
To supply power using equipment other than the included AC adapter, correctly
follow the pin number assignments in the “DC IN power connector” chapter of
the LX-1000 Instructions for Use.
Equipment could be damaged if connections are made with incorrect pin num-
bers or voltage that exceeds the guaranteed voltage operating range is supplied.
Installing and removing batteries
Screw A
Screw A
1 Loosen the 2 screws (A) on the front and open the cover.
2 Insert the batteries (3) in the direction shown by the arrows
on them.
3 Close the cover and tighten the two screws (A) to x it in
place.
oFollow these procedures in reverse to remove the batteries.
Specifications
Batteries used ...............................NP-L7S made by IDX Company, Ltd.
Number of batteries .......................................... 3 (sold separately)
DC power supply input
Rated input voltage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DC 9–34V
Guaranteed operating input voltage range ........................... DC 8–36V
Rated output voltage .................................................14.8V/18V
External dimensions ............................300 (W) × 201.5 (D) × 44 (H) mm
Weight ..............................................................about 1.9kg
Continuous operation time ........................................about 7 hours
(This is an estimate for a 16-channel model operating at room temperature with
AR-LXPA1000 units installed. The continuous operating time will vary according
to the use environment and operating mode.)
oIn order to improve the products, specifications and appearance could be
changed at any time without warning.
oWeight and dimensions are approximate.
oIllustrations in this document might differ in part from the actual products.
Warranty explanation
oThe warranty period for this device is one year from the date of purchase.
oBe aware that repairs will require payment in the following cases even during
the warranty period.
1) Malfunction or damage due to misuse
2) Malfunction or damage caused by modifications or repairs conducted by
any party other than our company or a service person designated by our
company
3) Malfunction or damage caused by dropping, transportation or similar
handling after product delivery
4) Malfunction or damage caused by fire, earthquake, water, lightning or
other natural disaster
5) Malfunction or damage caused by external factors, including power
supplies and equipment environmental conditions, that deviate from the
operation requirements of this product
6) Malfunction or damage if the product was not purchased from our com-
pany or an agent designated by our company
oWe offer paid service after the conclusion of the warranty period. For details,
please contact the retailer where you purchased the unit or a contact on the
back cover of this manual.
oBe aware that our company will bear no responsibility for any secondary
damages resulting from the operation of this device or related to data.
oBe aware that our company will bear no responsibility if data recorded by
this device is deleted as a result of misoperation or unexpected incident, for
example.
oInformation is given about products in this manual only for the purpose
of example and does not indicate any guarantees against infringements of
third-party intellectual property rights and other rights related to them. TEAC
Corporation will bear no responsibility for infringements on third-party intellec-
tual property rights or their occurrence because of the use of these products.
DISCLAIMER
TEAC disclaims all warranty, either expressed or implied, with respect to this
product and the accompanying written materials. In no event shall TEAC be lia-
ble for any damages whatsoever (including, without limitation, damages for loss
of business profits, business interruption, loss of business information or other
loss) arising out of the use of or inability to use this product.
Contact information
TEAC CORPORATION
1-47 Ochiai, Tama-shi, Tokyo 206-8530, Japan
Phone: [phone]
TEAC AMERICA, INC.
10410 Pioneer Blvd. Suite #1, Santa Fe Springs, California90670, U.S.A
Phone: [phone]
TEAC EUROPE GmbH. (EU Importer)
Bahnstrasse 12, 65205 Wiesbaden-Erbenheim, Germany
Phone: [phone]
TEAC SALES & TRADING (ShenZhen) CO., LTD.
Room 817, Xinian Center A, Tairan Nine Road West, Shennan Road, Futian District,
Shenzhen, Guangdong Province 518040, China
Phone: [phone]
Company names and product names in this document are the trademarks or registered
trademarks of their respective owners.
1119 MA-3005A