Ayyeka WAVELET 4R User manual

WAVELET 4R
QUICK START
GUIDE
AYYEKA
AYYEKA Jan 18, 2021
P/N 0100711 Rev 1

It is important that you read the Quick Start Guide
in a controlled environment prior to installation.
Set up, activate, and successfully test the entire
system (Wavelet 4R, sensors, and antenna
connection) indoors, in a controlled environment,
before going to the field for installation.
AYYEKA

for damage or injury as a result
of handling, installation, or maintenance of its supplied
systems.
AYYEKA IS NOT LIABLE
Contact for technical support:
[email protected]
[phone] (US)
[phone] (EMEA)
AYYEKA SUPPORT
Basic Wavelet Kit installation with
the local authority before starting installation works, which
should be completed by trained and authorized personnel.
ALWAYS COORDINATE
The offered by Ayyeka covers only Ayyeka
supplied hardware and software for the duration of the
warranty period as per the warranty terms and conditions.
WARRANTY
the Wavelet Kit because it contains a
lithium battery. Dispose of the battery properly.
DO NOT THROW AWAY
is required for proper
communication.
CELLULAR NETWORK SIGNAL
of -40°C to +80°C
(-40°F to +176°F).
OPERATING TEMPERATURE RANGE
IMPORTANT
1
AYYEKA

IP 68 / NEMA 6P
Wavelet Mechanical
Enclosure
Slots for Zip Ties
and/ or Bolts for
Attachment
AYYEKA
Magnetic Activator
Cellular Antenna
Port
Sensor Input Port
2
External Power
Port
7.3 cm 17.4 cm
FRONT
SCHEMATC
BOTTOM
(6.9 in)
(2.8 in)
13.3 cm
(5.2 in)
AYYEKA

1
3 4
2
GETTING STARTED
WAVELET 4R KIT
Wavelet ActivatorWavelet Device &
Protector
1x
1x 1x
1x 1x
M12 Field Attachable
Sensor Connector
(optional; ordered
separately)
(optional; ordered separately)
M8 Female Field Attachable
Power Connector
3
AYYEKA

Other tools and/or materials may be required (not included):
Rotary Hammer Electric Screw Driver
with Phillips PH1 bit
Zip Ties, Screws, and
Anchors
Cellular Antenna
(REQUIRED; ordered separately)
2x 4x 4x
5 6
4
AYYEKA

SENSOR CONNECTION
Connect the sensor cable assembly with the field attachable
connector to the mating panel connector on the Wavelet.
Turn the adjustable stainless steel end piece to secure the
field attachable connector to the Wavelet.
CAUTION: Do not turn the black plastic hood of the
connector. Turning the black hood may cause the wires to
disconnect, break, and/or damage the connector pins.
5
TURN HERE
DO NOT
TURN HERE
1
AYYEKA

2
3
6
EXTERNAL ANTENNA CONNECTION
Connect the cellular antenna to the antenna port (ANT 1).
The antenna does not appear in the remaining depictions
in this guide, but should remain connected once properly
secured to the appropriate panel connectors.
Cellular Antenna
IMPORTANT NOTE:
Place the magnetic Wavelet Activator on the embossed
Ayyeka logo on the front of the Wavelet enclosure. Wavelet
will initiate a 15 minute test mode of high frequency
sampling and transmission. The device will then return to its
default configuration.
AYYEKA
AYYEK A
AYY EKA

4
4
WAVELET ACTIVATION
Verify the installation with your mobile phone by using
AyyekaGo mobile application.
If you haven’t already done so, download the AyyekaGo
mobile app for iOS or for Android. Search the App Store or
Google Play for “AyyekaGo” or use the QR codes below
There are two ways to pair your phone with your Wavelet:
Access the Ayyeka user interface at home.ayyeka.com using
your log-in credentials. Expect data to appear
between 5 – 10 minutes after the test mode is initiated.
Select ”Get Key Via Web”. This will direct you to enter
your log-in credentials for the StreamView user interface.
1.
2. Select ”Enter Key Manually”. The Mobile Pair Key is found
in the StreamView user interface in the Devices tab.
7
AYYEKA

6
WAVELET ACTIVATION - continued
The screen display should resemble the following:
If the Wavelet is
transmitting properly,
you have completed the
installation successfully and
can begin collecting and
viewing your data!
If data does not transmit
properly, change the
Wavelet installation
location and activate again.
If the problem persists,
contact Ayyeka for
assistance:
[email protected]
[phone] (US)
[phone] (EMEA)
8
AYYEKA

If the Wavelet is installed in
an area with weak cellular
signal, activate the Wavelet
and place in the intended
installation location with
closed doors/access hatch.
Make sure the cellular
antenna is properly
installed to provide
adaquate signal quality.
Log in to
home.ayyeka.com to
ensure that cellular signal
has been recently updated
in the last few minutes.
Wait for at least 15 minutes,
then log in to the user
interface at
home.ayyeka.com to make
sure stable communication
is confirmed.
WEAK SIGNAL LOCATIONS: UNDERGROUND/INDOOR
WAVELET INSTALLATIONS:
AYYEKA 9
SPECIAL INSTALLATION LOCATIONS

7After the Wavelet completes the transmission process, place
the Wavelet protector above the connector ports and secure
the Wavelet protector into the Wavelet enclosure.
CAUTION: The protector is provided to shield the
connector from tampering or overexposure that could
result in disconnected wiring.
Insert the two lower clips into the two lower holes of the
Wavelet enclosure.
a.
a
b.
b
Snap the upper clips into place in the two grooves above the
panel connector.
Upper Clips
Lower Clips
10
AYYEKA
DEVICE PROTECTOR

8
4x
2x
1x4x 1x
Secure the Wavelet on a wall, pipe, or other secure
mounting location using zip ties or screws.
Wall
Mounted OR
Pipe
Mounted
11
AYYEKA

Ensure the antenna connector is secured tightly to the panel
connector.
Mount antenna under the open sky or at least 50cm (20 in.) beneath
any object.
Mount antenna at least 5 to 10cm (2 to 4in.) away from wall.
Mount antenna at least 5cm (2in.) away from the device.
Finalize the antenna setup to the exact physical conditions. For
example, close the lid, close the door, etc.
Make sure you have a signal and a successful data transmission by
using the magnetic key Activator to initiate more rapid transmissions.
DOs
Do not attach the antenna to the device.
Do not wrap cables, zip ties, or other items around the antenna.
DONTs
IMPORTANT NOTE: There are a few minutes of delay between a
successful transmission and the use of either of these methods for
initiating data transmission. Repeating the use of either method will not
expedite data transmission.
WARNING: If installing in a highly corrosive environment such as a
sewer, apply technical grease to the antenna and sensor field attachable
connectors after securing them to the panel connectors. Ayyeka
recommends using Dow Corning Molykote 55 O-Ring Grease, although
similar products can be effective.
ANTENNA MOUNTING
AYYEKA 12

If the device does not transmit, move the antenna to a different
position.
If the device still does not transmit after multiple attempts at
repositioning the antenna, consider using an alternative solution, such
as an in-road or a high-gain antenna.
Note: Ayyeka supplies antenna wall mounting hardware and various
antennas, including in-road antennas — contact Support for details.
If you intend to use your own antenna, verify that the antenna uses an
SMA male connector. Your antenna ideally supports all of the following
frequencies (make note of the model number suffix of your device – for
example “-US”):
ANTENNA TROUBLESHOOTING
USING YOUR OWN ANTENNA
AYYEKA 13

YOUR WAVELET 4R IS NOW
SUCCESSFULLY INSTALLED!
14
AYYEKA

WAVELET PINOUT
SENSOR PANEL CONNECTOR – M12 8-PIN MALE
Signal1 4-20mA or 0-24V Input #1
2 Pulse Counter/Digital Input #0 Signal
3 RS485 A and RS232 RXSignal
5 RS485 B and RS232 TXSignal
6 Pulse Counter/Digital Input #1Signal
7 4-20mA or 0-24V Input #2Signal
8 GNDCommon
4 Wavelet 12V Power Supply #1 (+)Supply
Connector
Pin #
#2
Function
Font
Back
Description Sensor Pin
Assignment
15
AYYEKA

No
Connection
If using an external power source, refer to the pinout below:
M8 3-Pin Female
Power Connector
+ Installation Tool
for Wire Termination
(Included)
S
W0
9
Cable Wire Cross
Section Surface Area
Wire Gauge
Cable Ø Diameter
0.14 – 0.5 mm2
AWG 26-20
4 – 5.5 mm
EXTERNAL POWER PANEL CONNECTOR – M8 3-PIN MALE
EXTERNAL POWER:
WAVELET PINOUT
Wire To Connect:
4
13
6-24VDC (+)
Negative (-)
4
3 1
Supply+1 6-24VDC
No Signal3 No Connection
Common4 Negative (-)
Connector
Pin #
Function Description
Font
Power Pin
Assignment
16
AYYEKA

Copy the first of the two GPS coordinates and paste into the
first box (identified above in red)
Copy the second GPS coordinate and paste into the second
box (identified above in blue)
Click Submit to save the new GPS coordinates associated with
this Site.
In the StreamView, click Devices in the left pane, and then click the
desired Site. On the right-hand side of the screen, in the lower
section with the map display, paste the GPS coordinates that you
copied from the Google Maps web page:
Unlike some other models of the Wavelet, the Wavelet 4R device
does not include an internal GPS. To take advantage of the map
features within the StreamView, you can identify the GPS
coordinates before field installation. Alternatively, during field
installation, you can manually add the GPS coordinates for the
device by using your smartphone, tablet, or laptop.
For guidelines on using Google Maps to find latitude and longitude
coordinates, refer to the Google Maps Help Center:
https://support.google.com/maps/answer/18539?hl=en&ref_topic=3092444
WAVELET 4R DEVICE LOCATION
17
AYYEKA

AYYEKA
www.ayyeka.com
[email protected]
[phone] (US)
[phone] (EMEA)
AYYEKA 18
QUESTIONS?