TEACH TECH TTG-684 Installation guide

From the Makers of
TTG-684 8 +
ASSEMBLY & INSTRUCTION MANUAL

Introduction P.1
Tools You May Need P.1
Mechanical Parts List P.1
Plastic Parts P.2
TIP: Cut off Burrs P.2
Operation P.18
Mechanical Assembly P.3
How To Play P.19
Trouble Shooting P.19
CONTENTS

Introduction
Mechanical Parts List
Tools You May Need
Diagonal Cutter
Safety Glasses
Important: If any parts are missing or damage, DO NOT RETURN TO THE
RETAILER. E-mail us at [email protected] or call [phone]
•
•Product contains functional edges and sharp points.
The Solar Rover is an all-terrain Solar vehicle, equipped with 6-Wheel mechanical
Suspension , planetary gear 4-wheel drive transmission and adjustable robotic arms.
This Rover conquers lunar terrain or your kitchen floor while learning about solar energy
and hands-on building.
Utilize the power of solar energy, with the Solar Rover on your next adventure.
QTY
1
P9
SOLAR ROVER
Gear (Yellow)
P2
QTY
1
Gear (Red)
QTY
1
P4
Gear (Orange)
P3
QTY
4
Sponge
QTY
2
P5
P1 Solar Panel With Motor
QTY
1
(2x26mm)
QTY
1
P6
Hex Shaft
Round Shaft
(Long)
QTY
2
P8
(2x23mm)
Round Shaft
(Medium)
QTY
1
P7
(2x16mm)
Round Shaft
(Short)
Foam
QTY
1
P11
1
Stickers
QTY
1
P10

2
Plastic Parts
Hints
Cut off the burrs before assembly.
burr
burr
Cut the plastic parts when they are required.
Do not cut them in advance.
35 6
7 8
11
12
10
9
2
1
4
A
D
3
5
6
7
8
10
9
2
2
1
4
C
5
6
7
8
11
12
9
2
1
3
4
B
10
Spare Part

1
3
Cut off burrs on B8
before assembly.
B 8
St i c k e r
St i c k e r
C2 B10 x2
M e c h a n i c a l A s s e m b l y
B8x2
A5
A7
2
Cut off burrs on B10
before assembly.
click

3
4
P1
P2
2
Incorrect
1
St i c k e r
St i c k e r
Correct
Correct
Caution:
Handle P1 with care.
R emov e
protectiv e film.
R emove paper backi ng from foam tape.
B1
P5 x2
R ed
R ed
R ed
Black
Black
Black
Incorrect

4
5
P4
( R ed)
Correct
Incorrect
Incorrect
Correct Incorrect
Black R ed
R ed
Black

5
6
P3
( Orange)
P8x2
( Medium)
P9
( Long)
C6 P3
( Orange)
C6
Cut off burrs on C6
before assembly.
1
2
3

6
7
P3
( Orange)
A6
Cut off burrs onA6 before assembly.
A 6
P4
( R ed)
P3
( Orange)
A6
C6
P3
( Orange)
P3
( Orange)
Incorrect
Correct

7
8
P6
C8
C9
Incorrect
Correct

8
9
Cut off burrs on B4 before assembly.
C1
B11x3
A9x3
A3
B2
C7
C3
B4
B5
B9
P7(Short)
Cut off burrs onA9 before assembly.
Cut off burrs onA3
before assembly.
A9
A3
B4
1
2

9
10
Make sure part C9 does not fall out.
A4
C9
St i c k e r
St i c k e r
St i c k e r
St i c k e r

1 1
1 0
11
click
B12
Cut off B8 burrs
before assembly.
B 8
C2
B10 x2
B8x2
Make sure B10 is fastened to end of B8.
St i c k e r

1 2
1 3
12
Hold the other side of B12, this will help in assembling of both B12.
Bottom V iew
Correct Incorrect
B12
B12 B12
R e m o v e A 7

14 15
13
Cut off burrs onA8 before assembly.
A8 A8
Cut off burrs onA8 before assembly.
P11x5
RL
C4 C5
A8
P11x5
A8

16
14
L
R
R
L
Incorrect
Correct
Incorrect
Correct

15
Cut off burrs on all
A11 parts
before assembly.
A11
P11x5
4
A11
17

1 8
16
A2
A1
A12
A12
B7 B7
Cut off burrs
before assembly. Cut off burrs before assembly.
B 7 B 7
Incorrect
Incorrect
St i c k e r St i c k e r

19
20
17
Cut off burrs on B3
before assembly.
B6
D
A10
C10
B3
B3
Incorrect
Correct

18
2 1 F inished
Op e r a t i o n
Set the mode switch to either the Automatic or Manual mode.
Place your Solar R ove r in the sunlight and tilt the solar panel so it faces directly into
the sun. The motor should start turning and your R ove r will come to life.
W hen you are not using your Solar R ove r ke ep it out of the sun so the motor won’ t
run. Also, don’ t use the Solar R ove r outdoors when it’ s raining.
If there is no sunlight, use a 5 0 W halogen light bulb to simulate the sun.
W ith a d u l t s u p e r v i s i o n , shine the lamp approxi mately five inches from the solar
panel. The light should be enough to drive the Solar R ov er.
CA U TI ON:
D o not shine the lamp on it more than three minutes as the heat may melt
the plastic frame.