TECHLIGHTING Bath Tigris 700BCTIGOS26 CF Series User manual

1.1
Installation Instructions for
Tigris Mirror Oval Surface (Compact Fluorescent) 700BCTIGOS26_-CF
1
920BCTOVSCF
GENERAL PRODUCT INFORMATION:
This product is suitable for damp locations.
Bring 120 Volt power supply to the mirror in accordance
with local electrical codes.
This instruction shows a typical installation. C AUTION — RISK OF FIRE
This product requires installation by a qualified
electrician. Before installing be sure to read all
instructions and TURN THE POWER TO THE
ELECTRICAL BOX OFF.
BATH COLLECTION
Locate the studs on the wall where the mirror is going
to be mounted (Max 22-1/2" separation).
If necessary, use the center hole on the backplate to
position the backplate on the wall.
Use minimum of four slots to mount the backplate to
the studs with four screws and washers provided. Do
not drive the screws all the way in at this time.
1A
Bring the power line to one of the four circular holes on
the backplate.
While holding the backplate level and in the desired
position, tighten the four screws to secure it.
BACKPLATE
1B
POWER LINE
SCREW
STUD
WASHER
CENTER
HOLE
Install the Hardware
1
2
3
1 1
2
3 3
3 3
4
5
4
5
5 5
5

2
Install the Pan
3A
THREADED ROD
POWER LINE
Feed the power line wire through the conduit connector
into the pan.
Place the pan holes onto the backplate threaded rods.
3B
Tighten the nuts to secure the pan onto the backplate.
Refer to "Replace the Lamps" on page 4 to replace the
lamps.
1
2
1
2
3
4
Prepare the Mirror for Installation
Remove the two screws on top and bottom of the
electrical box in the center of the pan.
Remove the electrical box lid.
Remove one knockout and install the provided conduit
connector.
2A ELECTRICAL
BOX
KNOCK OUT
LID
SCREW
1
2
3
1
1
2
2B
Pull out the lamps on the left and right side. This will
clear the two side pan holes for installation.
4
LAMP
PAN
HOLE
SOCKET
PAN
HOLE
LAMP
ELECTRICAL
BOX
4
4
2
PAN
HOLE
CONDUIT CONNECTOR
PAN HOLE
2NUT
NUT
33
3
3

3
4A
Connect the neutral 120 volt power line wire to the
loose white fixture wire with a wire nut.
Connect the hot 120 volt power line wire to the loose
black fixture wire with a wire nut.
Connect the stranded copper wire to ground in
accordance with local electrical codes.
Refer to "Replacing the Lamps" on page 4 to replace the
lamps.
1
2
3
4
120 VOLT
POWER
LINE WIRES
1
2
Connect Power
Replace the lid onto the electrical box and tighten the
two screws.
Carefully attach the mirror onto the hinge and tighten
the two screws.
5A LID
SCREW
HINGE
SCREW
1
2
2
2
1
1
Attach the Mirror
3

4
SAVE THESE INSTRUCTIONS!
7400 Linder Ave, Skokie, IL 60077
847.410.4400
www.techlighting.com
© 2008 Tech Lighting, L.L.C. All rights reserved. The "Tech Lighting" graphic is
a registered trademark of Tech Lighting, L.L.C. Tech Lighting reserves the right
to change specifications for product improvements without notification.
A Generation Brands Company
Replace the Lamps
Pull out the old lamp.
Push the new lamp pins firmly all the way into the
socket holes.
NOTE: Use only your fingers to replace the lamp.
6A
1
2
ELECTRICAL BOX
SOCKET
LAMP
1
2
Use MAX 9 Watt Twin-Tube
Compact Fluorescent Lamp.