Technaxx 4218 User manual

Technaxx® * User Manual
Video Wall Clock HD 720p
Clock with built-in CMOS video camera and HD video resolution
for wall mounting or table and shelf
The Declaration of Conformity for this device is under the Internet link:
www.technaxx.de/ (in bottom bar “Konformitätserklärung”). Before using the
device the first time, please read the user manual carefully.
This device has a rechargeable battery. It must be fully charged before
first use. NOTE: Charge the battery of the device every 2–3 month if it is
not used!
Service phone No. for technical support: 01805 012643 (14 cent/minute from
German fixed-line and 42 cent/minute from mobile networks).
Free Email: supp[email protected]
Keep this user manual for future reference or product sharing carefully. Do the
same with the original accessories for this product. In case of warranty, please
contact the dealer or the store where you bought this product.
Warranty 2 years
Features
Clock with built-in CMOS video camera for wall mounting or table
and shelf
HD video resolution 720p
Inconspicuous camera lens in the dial
PIR motion detection sensor
Manual recording function
Audio recording by hidden microphone in USB port
Easy handling

Technical specifications
Video resolution 1280x720 with 30fps, AVI format
PIR sensor range ~3–8m with 70° angle
Built-in rechargeable 1000mAh lithium polymer battery:
Charging ~5 hours / Recording ~5 hours / Standby ~25 days
Storage MicroSD* card up to 32GB (*not included)
Circle recording: if memory card is full with data, it starts overwriting the
earliest recorded video(s). If you want to keep some videos, you have
to change the video’s name, then it is not overwritten
Charging voltage DC 5V or 1A power adaptor* (*not included)
Separate AA battery* for clock operation (*not included)
Operation systems Windows 7 / 8 / 8.1 / 10 / XP / 2003
Material Plastic in metal look
Weight / Dimensions 500g / Ø 22cm, thickness 4cm
Package contents Video Wall Clock HD 720p
, USB cable, DC cable,
Stand, User Manual
Security and Disposal Hints for Batteries: Hold children off batteries.
When a child swallowed a battery go to a doctors place or bring the child
into a hospital promptly! Look for the right polarity (+) and (–) of batteries!
Always change all batteries. Never use old and new batteries or batteries of
different types together. Never short, open, deform or load up batteries!
Risk of injury! Never throw batteries into fire! Risk of explosion!
Hints for Environment Protection: Packages materials are raw materials
and can be recycled. Do not disposal old devices or batteries into the
domestic waste. Cleaning: Protect the device from contamination and
pollution (use a clean drapery). Avoid using rough, coarse-grained
materials or solvents/aggressive cleaner. Wipe the cleaned device
accurately. Distributor: Technaxx Deutschland GmbH & Co.KG, Kruppstr.
105, 60388 Frankfurt a.M., Germany

Product overview
Camera = Video camera
1 Hanging hole 4 Battery
2 Microphone 5 Stand
3 Lens adjustment 6 Time adjustment

Stand
Remove back cover
There is a buckle on the back cover. When removing it (or install it
again), the buckle has to be fitted exactly into the the “buckle port”
press and slide down at straight line.
(1) With both hands press
gently on the back cover, to
snap it out of the buckle. (2)
Pull it back to use it as stand to
put the clock to a table or
closet. (3) If continue to slide,
you can remove the back cover
completely.
Buckle

Rear view with back cover removed
USB Charging
Use the provided USB cable connect the clock to a computer for
charging, or optional use the DC cable for charging. While
charging, the RED light keeps on lightening and the BLUE light
keeps flashing. When the battery is fully charged, the BLUE light
turns off. It takes approx. 5 hours until the 1000mAh battery is fully
charged.
MicroSD card
ON / OFF
Reset
Buckle port for stand USB port
Power „P“ function button
DC charging port

DC 5V Charging
Connect the clock to a socket with the included DC cable the
RED light turns on. It takes approx. 5 hours until the 1000mAh
battery is fully charged. The clock can be charged via the DC port
while the camera is recording at the same time.
Make sure an MicroSD card is plugged in the slot before
starting recording!
Power ON
Switch Power button to “ON” position
Lens adjustment
There is a lens adjustment wheel at the back of the clock. Adjust the
camera’s angle according to its position and height. Slide the wheel
tenderly to avoid damage.
Sliding up the wheel: The camera watchs more down.
Sliding down the wheel: The camera watchs more up.
PIR sensor detection recording
Press the power “P” function switch button the YELLOW light
flashes 6 times the camera enters into PIR recording in case
of persons enter the secured PIR area the camera starts
recording automatically.
Once people left the PIR area the camera stops recording and
goes back to the standby status after 1 minute.
Press the power “P” function button shortly while recording the
camera will stop recording at once and save the video switch the
power button to “OFF” position if camera is not used.

Manual recording
To start manual recording press the power “P” function button
about 3 seconds the RED light flashes 4 times and then the
BLUE light turns on then light turns off the camera starts
recording directly (it is regular recording, not PIR recording!).
To stop manual recording and to save the video press the
power “P” function button shortly.
Connection to PC
Press shortly the power "P" fuction button to stop the camera
working and then switch the power button to "OFF" position.
Connect the clock with the provided USB cable to a PC.
On the PC screen a "Movable Disk" will pop up. In case you
cannot open the “Movable Disk”, check if a MicroSD card is plugged
inside. In case the PC cannot detect the clock’s camera, check if
USB port on PC maybe is too loose and/or try another USB port.
Open it and the recorded video can be watched.
If you want to disconnect, go to the computer’s "task bar" on the
lower right corner and click the “Movable Device Management” icon.
Then uninstall the removable storage devices.
After the message "safely withdraw" pops up, confirm it.
Then the clock can be disconnected from the computer.
NOTE: In case the indicator light still keeps bright after
disconnecting the clock from the computer, press the RESET switch
on the back of the clock to turn the light off.

Time and date setting
Set the time and date in the text file „time.txt“ as follows:
Create a text file in the root directory named "time.txt". Then open
the text file. Type in date and time as follows (example):
2017 02 25 10:50:00 Then save the file and close it.
Create „time.txt“
Connect the clock a PC/Notebook (USB cable included)
Open the removable disk of the clock.
Click with the right mouse button on a blank space in the root
directory of the clock’s removable disk.
A menu opens move the cursor to the „New“ option.
Select with right mouse button „Text Document“ and rename it to
„time“. It is essential that its extension is ".txt" !
Open the „time.txt“ text document to type in date and time (like
described above).
Then click with left mouse button on „File“ in the upper menu bar
Click with the left mouse button on „Save“.
Warnings
Do not attempt to disassemble the clock, it may result in shortly-circuit
or even damage. Do not drop or shake the clock. It may cause internal
mechanical damage. Use it under normal temperature and normal
humidity. The clock is NOT waterproof. Shooting illumination: use it in
well lighted environment, but do NOT face it to powerful light directly (this
may damage the lens) Do not use under high dust density environment,
to avoid the lens and other components stain dust and effect the camera
quality. Do not make its strong shock, vibration, do not use under high
magnetic field. Keep the clock away from little children.