Techness SE800 User manual

User Guide for TECHNESS SE800
Console SM2634-67
Thanks for buying a TECHNESS item. This product has been designed
for your full satisfaction. Please read carefully the user guide before
assembling and training.

PARTS LIST
Number
Description
Qty
Unit
A
Console
1
PCS
A-1
Screw
4
PCS
B
Front handlebar set
1
PCS
B-1
STR foam
2
PCS
B-2
Hand pulse
2
PCS
B-3
End cap
2
PCS
B-4
Self-tapping screw
2
PCS
B-5
Semi-circle washer
2
PCS
B-6
Cable
1
PCS
C
Left handlebar (upper)
1
PCS
C-1
End cap
2
PCS
C-2
STR foam
2
PCS
C-3
Right handlebar (upper)
1
PCS
D
Handlebar post
1
PCS
D-1
Cable (upper)
1
PCS
D-2
Screw
2
PCS
D-3
Cover for console holder(Left)
1
PCS
D-4
Cover for console holder(right)
1
PCS
D-5
Bushing
2
PCS
D-6
Axle for the handlebar
1
PCS
E-L
Left handlebar(lower)
1
PCS
E-R
Right handlebar(lower)
1
PCS
E-1
Bushing
4
PCS
E-2
C type ring
4
PCS
E-3
Flat washer
4
PCS
E-4
Bushing
4
PCS
E-5
Sleeve
2
PCS
E-6
Wave washer
4
PCS
F
Main frame
1
PCS
F-1
Cable wire
1
PCS
F-2
Flat washer
4
PCS
F-3
Screw
4
4
F-4
C type ring
1
PCS

Number
Description
Qty
Unit
F-5
Wave washer
1
PCS
F-6
Flat washer
1
PCS
F-7
Bearing
2
PCS
F-8
Sensor box
1
PCS
F-9
Pulley
1
PCS
F-10
Hex. Screw
3
PCS
F-11
Belt
1
PCS
F-12
Sleeve
1
PCS
F-13
Axle
1
PCS
F-14
Self-tapping screw
5
PCS
F-15
Inside cover for the disc
2
PCS
F-16
Cross bar
2
PCS
F-17
Flat washer
4
PCS
F-18
Cover for the disc
2
PCS
F-19
Front cover (R )
1
PCS
F-20
Chain cover(R )
1
PCS
F-21
Self-tapping screw
8
PCS
F-22
Disc
2
PCS
F-23
Chain cover(L)
1
PCS
F-24
Self-tapping screw
7
PCS
F-25
Front cover (L)
1
PCS
F-26
Cover for the handlebar post
1
PCS
F-27
Screw for the sensor box
1
PCS
F-28
Adaptor
1
PCS
F-29
DC wire
1
PCS
G
Flywheel set
1
PCS
G-1
Sleeve
1
PCS
G-2
Nut
5
PCS
G-3
Bearing
1
PCS
G-4
Sleeve
1
PCS
G-5
Bearing
1
PCS
G-6
Flat washer
1
PCS
G-7
Star washer
2
PCS
G-8
Axle for the flywheel
1
PCS
H
Idler set
1
SET
H-1
Spring
1
PCS

Number
Description
Qty
Unit
H-2
Spring holder
1
PCS
H-3
Hex. Screw
1
PCS
H-4
Hex. Screw
1
PCS
H-5
Flat washer
1
PCS
H-6
Flat washer
1
PCS
H-7
Idler wheel
1
PCS
H-8
Wave washer
2
PCS
H-9
Flat washer
1
PCS
H-10
Nylon screw
1
PCS
H-11
Hex. Screw
1
PCS
I
Magnetic set
1
PCS
I-1
Sleeve
1
SET
I-2
Hex. Screw
1
PCS
I-3
Flat washer
1
PCS
I-4
Chain
1
PCS
I-5
Hex. Nut
2
PCS
I-6
Sleeve
1
PCS
I-7
Flat washer
1
PCS
I-8
Screw for the gear box
1
PCS
I-9
Nylon screw
1
PCS
J
Rear stabilizer set
1
SET
J-1
Block for the adjustable foot cap
4
PCS
J-2
Adjustable foot cap
4
PCS
J-3
Foot cap
4
PCS
J-4
Front stabilizer set
1
SET
J-5
Nylon nut
2
PCS
J-6
Flat washer
2
PCS
J-7
Transportation wheel
2
PCS
J-8
Screw
2
PCS
K-L
Pedal arm set (Left)
1
PCS
K-1
Screw
4
PCS
K-2
Front cover for pedal arm(L)
2
PCS
K-3
Bushing
4
PCS
K-4
Front cover for pedal arm(R )
2
PCS
K-5
Left pedal
1
PCS
K-6
Right pedal
1
PCS

Number
Description
Qty
Unit
K-R
Right pedal arm set
1
PCS
L-1
Self-tapping screw
1
PCS
L-2
Bolt
4
PCS
L-3
Nut
4
PCS
L-4
Semi-circle washer
4
PCS
L-5
Cap
4
PCS
L-6
Nylon screw
4
PCS
L-7
Plastic washer
4
PCS
L-8
Flat washer
4
PCS
L-9
Wave washer
4
PCS
L-10
Nylon nut
2
PCS
L-11
Screw
8
PCS
L-12
Sleeve
4
PCS
L-13
Knob for the pedal
8
PCS
L-14
Spring washer
8
PCS
L-15
Bolt
8
PCS
L-16
Screw
2
PCS
L-17
Flat washer
2
PCS
L-18
Metal cap
1
PCS
L-19
Flat washer
2
PCS
L-20
Spring washer
2
PCS
L-21
Screw
2
PCS
L-22
Flat washer
4
PCS

ASSEMBLY STAGE # 1:
1
1. Fasten front and rear stabilizers to the main frame using 2 carriage bolts (L-11).
After assembly, the Trainer can be adjusted to slightly uneven ground by adjusting the height of
the foot caps at the front and back. The pre-assembled transportation wheels in the front allow
easy moving of the Elliptical and therefore during assembly, need to be pointing down at the front
(45°).

ASSEMBLY STAGE # 2:
2
1. Assemble the pedal arm (K-L, K-R) to the disc by Plastic washer (L-7), flat washer (L-8), wave
washer (L-9) and nylon screw (L-6).
2. Assemble the cap (L-5) for pedal arm (K-L, K-R).

ASSEMBLY STAGE # 3:
3
1. Put pedal (K-5, K-6) onto the pedal arm and tighten it, using 4 knobs (L-13), flat washers
(L-22), spring washer (L-14), sleeve (L-12) and bolts (L-15) in each side.
Please note that the left and right pedals need to be placed in identical positions.

ASSEMBLY STAGE # 4:
4
1. Pull the cable out of the handlebar post and before assembling Step 4.
2. First, loosen the pre-assembled screws.
3. Connect the cable upper by pushing the head into the notch of the cable lower coming from the
main frame (see drawing). Connect the cables completely
4. Put the cover (F-26) and handlebar post (D) into the main frame and fix it with 4 screws (F-3)
with flat washer (F-2).

ASSEMBLY STAGE # 5:
5
1. Disassemble one side of the pre-assembled screw (L-6) on axle; insert the axle into the whole
movable handlebars and handlebar post. Then tighten the end using one plastic washer (L-7), flat
washer (L-8), wave washer (L-9) and screw (L-6) in each side.
2. Tight the screw (L-16) with flat washer (L-17) and nylon nut (L-10) to connect the pedal arm and
lower swing arm in each side.

ASSEMBLY STAGE # 6:
6
1. Assemble the front cover for the pedal arm (K-2, K-4) by screw (K-1) in each side.

ASSEMBLY STAGE # 7:
7
1. Mount the fixing handlebar (B) onto the handlebar post and tighten the metal cap (L-18) for
handlebar post with the flat washers (L-19), spring washers (L-20) and screws (L-21).

ASSEMBLY STAGE # 8:
8
1. Mount the computer (A) on the plate with 4 screws (A-1).

ASSEMBLY STAGE # 9:
9
1. Assemble the cover for the console holder by screw (D-2) and self-tapping screw (L-1).

ASSEMBLY STAGE # 10:
10
1. Assemble the upper handlebar (C, C-3) by bolt (L-2) with nut (L-3) and semi-circle washer
(L-4).

EXPLODED DRAWING

G
G- 4
G- 3
G- 2
G- 1
G- 5 G- 6 G- 7 G- 8

KIT
L- 14: Spr i ng
( 8)
L- 22: flat washer
*1T (4)
L-4:Curved Washer for M8 bolt (4)
L-6:Hex bolt
M8*P1.0*20L(4)
L- 8:flat washer 10* *2T (4)
L-9:Curved Washer
17.5* 25*0.3T(4)
L- 7:Teflon washer
10* *0.5T (4)
SE01
( 8)

L-18:Metal cover (1)
L- 20: Spr i ng Washer f or
( 2)
L- 19: flat washer 7* *1T (2)
L- 21: Allen Bolt M7*P1.0*30L(2)
L- 16: allen bolt M8*P1.25*55L (2)
L- 15: Carriage Bolt M6*P1.0*50L (8)
Box Spanner (2)
Allen Key(1)
SE01
L-10:lock nut for M8 (2)
L- 2: Carriage Bolt
M8*P1.25*40L (4)
L-3 :Acorn Nut for M8 Bolt (4)
L-11: Allen Bolt M8*P1.25*16L 8pcs
L-17 Washer
16 t(2) L-1 Screw M3*25L(1)

CONSOLE SM2634-67 INSTRUCTION MANUAL
Button functions
ENCODER UP
To select training mode and adjust function value up.
ENCODER DOWN
To select training mode and adjust function value down.
ENTER
To set function value for TIME, DIST, CAL, PULSE in sleep mode.
RESET
Return to main function mode in STOP mode and clean all preset function
values to zero.
START/ STOP
To start or stop training.
RECOVERY
To test heart rate recovery status.
TOTAL RESET
To power on the computer again.