SportsArt Fitness ECO-NATURAL Elite E874 User manual

E874 LCD OWNER’S MANUAL CONTENTS
1. INTRODUCTION ............................................................................ 3
2. SAFETY PRECAUTIONS .............................................................. 4
3. WARNING LABEL POSITION ....................................................... 7
4. LIST OF PARTS ............................................................................ 8
5. ASSEMBLE THE PRODUCT .......................................................... 11
STEP 0 Preparation: Battery Instructions .......................................... 11
STEP 1 Install the Main Frame .......................................................... 12
STEP 2 Install the Console ............................................................... 15
STEP 3 Install the Outer Link Pedal Arm Covers ................................. 16
STEP 4 Install the Front Base Cover................................................... 17
STEP 5 Install the Pedals ................................................................... 18
STEP 6 Precautions When Installing the Pedals ................................ 19
STEP 7 Move the Elliptical Trainer in Place ........................................ 20
STEP 8 Level the Product ................................................................... 21
STEP 9 Ground Wire Installation Instructions ...................................... 22
6. UNDERSTAND THE E874 LCD DISPLAY ...................................... 23
DISPLAY Overview ........................................................................... 23
DISPLAY Console Panel ................................................................... 23
DISPLAY Windows Display ................................................................ 24
DISPLAY Specications ..................................................................... 24
DISPLAY Button Functions ................................................................ 25
7. OPERATE THE PRODUCT ........................................................... 27
OPERATION Safe Operating Area ................................................... 27
OPERATION Beware of Moving Parts ............................................... 28
OPERATION Essential Functions Guide ........................................... 29
OPERATION Safely Get On/O󰀨 ........................................................ 30
OPERATION Proper Workout Position ............................................... 31
OPERATION Start Screen ................................................................ 32
OPERATION <GO>Mode ................................................................... 32
OPERATION User Setting Procedure ............................................... 32
OPERATION Workout Programs ....................................................... 35
OPERATION During Exercise ........................................................... 38
OPERATION Cool Down ................................................................... 38
OPERATION Stop Exercise .............................................................. 38
OPERATION Workout Summary ....................................................... 38
OPERATION Idle Mode ..................................................................... 39
OPERATION Auto Power O󰀨 Function .............................................. 39
OPERATION User Parameter Setting ............................................... 40
8. ABOUT HEART RATE DETECTION ............................................. 42
HEART RATE Telemetry ................................................................... 42
HEART RATE Contact ...................................................................... 42

E874 OWNER’S MANUAL CONTENTS
9. GUIDELINES FOR EXERCISE ..................................................... 43
10. MAINTENANCE .......................................................................... 44
MAINTENANCE Safety Precautions ................................................. 44
MAINTENANCE Error Messages ....................................................... 45
MAINTENANCE Messages ................................................................ 46
MAINTENANCE Lubrication ............................................................... 46
MAINTENANCE Lubrication Procedure .............................................. 47
MAINTENANCE Cleaning the Glide Rails .......................................... 48
MAINTENANCE Schedule ................................................................ 49
11. ACCESSORIES ............................................................................. 50
ACCESSORIES Standard ................................................................... 50
ACCESSORIES Option ..................................................................... 51
12. APPENDIXES ............................................................................. 53
APPENDIXES Specications ............................................................. 53
APPENDIXES Electronics Block Diagram ......................................... 54
APPENDIXES Exploded Diagrams..................................................... 55
APPENDIXES Disassembly ............................................................... 56

3
1. INTRODUCTION
Congratulations on the purchase of a high quality SportsArt product, the E874
Elliptical trainer. Constructed of high quality materials and designed for years of
reliable performance, this product was made for full commercial use.
Before this product is assembled or operated, we recommend that you familiarize
yourself with this manual. Understanding the correct assembly and operation of
this product will help ensure that exercisers obtain their tness goals safely and
successfully.
2085mm(82”)
1765mm(69.5”)
680mm(26.8”)

4
2. SAFETY PRECAUTIONS
This product was designed and built for optimum safety. However certain
precautions apply during the use of this product. Please note the following
safety precautions:
● To reduce the risk of personal injury, read and understand all the instructions
before using this product.
● Make sure the product is installed and operated as instructed in this
manual. Be careful when mounting and dismounting the unit.
● Use this product only for the intended use described in this manual.
● Check the product before every use. Make sure all parts are assembled,
and all fasteners are tightened. Do not use the product if it is disassembled
in any way.
● Do not leave your device unattended while in use.
● Assemble and operate the product on a solid, level surface. Do not use
outdoors or near water (including swimming pools and saunas) and should
not be used where aerosol (spray) products or oxygen are used. Do not
operate on a blanket or near ammable materials.
● Keep all air ventilation areas free of blockage. Never drop or insert into
any opening.
● The product should be positioned away from walls to avoid injury due to
falls. Be sure that the back of the product has at least six to seven feet of
clearance from a ledge, wall or window.
● Wear appropriate workout clothes, don’t wear loose clothing, tie all long
hair back, wear shoes with rubber or high traction soles, don’t wear shoes
with leather soles/high heels or barefoot use this product.
● Never place liquids of any type directly on the unit, except in a bottle
holder or accessory tray. Lidded containers are recommended.
● Keep away from moving parts. Moving parts may or may not stop
immediately if an object becomes caught or impedes normal motion.
● Never operate this product if it has been damaged in any way. If it is
not working properly, if it has been dropped or damaged, or dropped into
water, contact a service technician for repairs.
● Do not use accessories or parts that are not specically recommended
by the manufacturer (SportsArt). Such parts might cause injuries or cause
the unit to fail and void the warranty. We will not be responsible for any
safety issue that arises due to the misuse of accessories or parts. At the
same time, we will terminate the warranty terms of this equipment.
● Unpack and verify contents of boxes according to the list of parts to check
if any parts are missing. If the product is damaged or missing, contact your
SportsArt representative to nd out all the materials that were damaged
during shipping. (Note: Transport damage is the responsibility of the
carrier.)
● This product is not intended for use by persons (including children 12
or younger) with reduced physical, sensory, or mental capabilities, or by
people who are otherwise decient in product knowledge or experience.
If such people use this product, they should be given training and be
supervised at all times by someone responsible for their safety.

5
2. SAFETY PRECAUTIONS (CONT.)
● CAUTION : The heart rate system is for reference only, if you feel any pain
or any abnormal feeling, please stop Exercise and consult your doctor
immediately.
● Consult your physician before starting a workout or training program. It is
recommended that you undergo a complete physical examination. Have
your doctor review your training and diet programs to advise you of a
workout routine you should adopt.
● WORK within your recommended exercise level. DO NOT work to
exhaustion.
● Before using this equipment to exercise, always do stretching exercises
to properly warm up.
● WARNING! Only qualied technicians should be allowed to contact
electrical components such as circuit boards.
● Noise emission under load is higher than without load.
● This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If the user desires to correct the
interference, it is at the user’s own expense.
● The recommended minimum operating temperature is 15 degree Celsius.
● The user weight limit for this product is 205kg (450lb).

6
2. SAFETY PRECAUTIONS (CONT.)
MARKINGS
CAUTION:
● Read instruction manual before using.
● Do not let children on or near the product.
WARRING:
● Heart rate monitoring system may be inaccurate.
● Over exercise may result in serious injury or death.
● If you feel faint, stop exercising immediately.
● This stationary training equipment is not suitable for hight accuracy
purposes.

7
3. WARNING LABEL POSITION
If you are in French-speaking areas in North America, display the warning
label on console panel as shown below, or in an obvious location that is
visible to the user.
NOTE: The label is available exclusively in French-speaking areas in North
America.

8
4. LIST OF PARTS
A1
A2
A3
A5 A6
A10
A7
A8
A9
A4
A11
A12
Assembly Parts
No. Name Qty. No. Name Qty.
A1 Main frame 1 A7 Front base cover 1
A2 Stationary handlebar 1 A8 Left support tube 1
A3 Console 1 A9 Right support tube 1
A4 Left/right joint covers 2 A10 Foot pedals 2
A5 Left pedestal cover 1A11 Pedal bottom covers 2
A6 Right pedestal cover 1 A12 Outer link pedal arm
covers 2

9
4. LIST OF PARTS (CONTINUED)
HARDWARE KIT
No. Name Qty. Specication Notes
10 Inner hex screw 6 M10*P1.5*L20
Toothed lock washer 6 D20*d10.2*t2.0
11
Secondary roller axle 2 D9.96*L54
self-lubricating bushing 4
Secondary roller 2
12 Stride adjustment linkage cover 2
13 Hex nut 2 M10*P1.5
Stopper 2 Ø30-30
14 Round shaped screw cap 4
15 Mushroom top philips screw 8 M4*L16
Round shaped screw cap 4
16 Round head Philips screw 2 M5*P0.8*L12
17 Mushroom top philips screw 4 M4*L12
18 Round shaped screw cap 1
L-shaped Allen wrench 1 M4
L-shaped Allen wrench 1 M5
L-shaped Allen wrench 1 M6
L-shaped Allen wrench 1 M8
Outer Hexagon Wrench 1 13*15
Double open-end wrench 1 14*15

10
4. LIST OF PARTS (CONTINUED)
Pre-Installed Hardware
No. Name Specication Notes
33 Hex socket at head cap screw M10*P1.5*L20
34 Inner hex screw 5/16”*L2-1/4”
Half tooth
Flat washer D20*d8*t2.0
35 Mushroom top inner hex screw M8*P1.25*L15
Flat washer D17*d8.3*t2
36 Inner hex screw M6*P1.0*L15
Handlebar washer D20*d7*t2
37 Mushroom top inner hex screw M6*P1.0*L15
Flat washer D13*d6*t1
38 Mushroom top philips screw M5*P0.8*L12
39
Inner hex screw M6*P1.0*L15
Flat washer D13*d6*t2.0
Toothed lock washer D20*d6.2*t2.0
40 Mushroom top philips screw M5*0.8*L8
41 Mushroom top inner hex screw M5*P0.8*L16

11
5. ASSEMBLE THE PRODUCT
STEP 0 Preparation: Battery Instructions
Before start using the elliptical trainer, remove the protective cover (a) and
turn the battery switch on.
0-1 The unit can generate its own power. The battery provides backup power
in case of insu󰀩cient power which may cause the unit fail to work.
0-2 After nishing assembly, be sure to turn on the battery switch.
0-3 The battery lasts 1.5 years after fully charged the rst time. Battery life
varies by use.
0-4 To prevent your battery from draining, turn the unit all the way o󰀨 when
not in use for an extended period of time.
0-5 If you need to charge the battery, identify the correct charger for the
battery and make sure your charger is compatible.
a

12
STEP 1 Install the Main Frame
(1) Remove all packaging material and place the main frame on the carton
base.
(2) Lift the console mast into upright position, and then tighten the following
screws in sequence: screw (33) in (area D), screw (10) in (area A), and
screws (10) in (area B,C).
(3) Lift left/right swing arms①and pedal arms②as shown in the figure be-
low, and place the pedal carriages on the carton base.③
(4) Carefully take out the glide rail (E) from the carton base while the swing
arms and pedal arms are lifted.

13
STEP 1 Install the Main Frame (Cont.)
(5-1) (a) Slip the glide rail into the pedal carriage and lower swing arm. (b)
Install the secondary roller (11) to the bottom of glide rail. (NOTE:
Insert the axle toward inner side from outer side)
(5-2) Insert the axle shaft into housing on the pedal arm, then tighten screw
(34) to secure the assembly, and put the stride adjustment linkage cov-
er (12) on. (NOTE: repeat on other side)
(5-3) Secure the stopper (13) to the front side of the glide rail on both sides.
NOTE: Read and follow all assembly instructions in this manual. Incorrect
assembly may present a danger to the exerciser, damage the ellipti-
cal and void the warranty.
a
b
(2)
(1)
(3)

14
STEP 1 Install the Main Frame (Cont.)
(6-1) Insert left and right support tubes (A8)(A9) into the axle area and base,
and loosely secure them into place with screws (35) (36)
(6-2) Install the stationary handlebar (A2) to the left/right support tube and
using screw (37) to secure the assembly. Once you have nished,
tighten the screws (35)(36) in (area A) and (area B).
(6-3) Remove screw (38) from the side of the left/right support tube (A8)
(A9). Snap joint covers (A4) together and secure them with screws
(38), and then put the round cover on.
(1) (2)
(3)
A4
A4
38
38

15
STEP 2 Install the Console
(1) Remove the following parts from the console(A3): anti-slip pad (51),
screws (52)(53), and bottle holder (54).
(2) Secure the console (A3) to the main frame (A1) with pre-installed screw
(39).
(3) Remove the rear cover (55), and then connect the cables of the main
frame (A1) to the cables of the console (A3). Tuck the cables away in the
console for a cleaner look, and then put back the bottle holder (54) and
secure it with screws (52)(53). After that, put on the anti-slip pad (51) and
the round shaped screw cap (18).
51
52
53
54
39
55
A3
A3
A1
A1
(1) (2)
(3)
51
18
52
53
54

16
STEP 3 Install the Outer Link Pedal Arm Covers
(1) Rotate the pedal arm to the position shown in the gure below, then put
on cover B and rotate it 270 degrees clockwise.
(2) Snap cover B and cover C together, and rotate the pedal arm until (area
A) is easily accessed, then tighten screws (16)(17). Repeat on other
side.
A12
A
BB
A
270
17
16
C

17
STEP 4 Install the Front Base Cover
Secure left/right pedestal cover(A5)(A6) to the main frame using screw (15),
then put on the round shaped screw cap (15) and the front base cover (A7).
NOTE: Install the ground wire first before putting the front base cover on.
A5
15
15
A6
A7

18
STEP 5 Install the Pedals
(1) Secure the pedal bottom cover (A11) to the main frame using screws (40),
and then put on the round shaped screw cap (14).
(2) Pull up part A, and then secure the foot pedal (A10) onto its mount on the
pedal carriage (A1) using screw (41).
(3) Press fit part A and part B together. (NOTE: do not pull put the 2 pins in
the middle)
41
A11
40
40
14
14

19
STEP 6 Precautions When Installing the Pedals
(1) Make sure the 2 nibs in (area L) are pushed into the holes on the foot
pedal.
(2) Tighten screws (m1), then push the 2 nibs in (area M) into the holes on
the foot pedal.
(3) Tighten screws (n1), then push the 2 nibs in (area N) into the holes on
the foot pedal.

20
STEP 7 Move the Elliptical Trainer in Place
Grip and lift the main base of the elliptical trainer, and then move it to the
desired location. Be careful not to pinch your ngers when you put down the
elliptical trainer.