Techni-Lux Pro Series Tracker SPOT250 User manual

Information specifically for:
IL-TRACKER250S/1
V1.1
This manual contains important information.
Please read before operating fixture.

2
© 2005 Techni-Lux Inc.

3
IMPORTANT INFORMATION
Save original packing and documentation for warranty, service and return issues.
Limited Warranty: This warranty covers defects or malfunctions in this equipment. This warranty lasts for
a period of one year from date of purchase. It is the owner’s responsibility to provide invoices for proof of
purchase, purchase date and dealer or distributor. If purchase date can not be provided, warranty period
will start at manufacture date. It is the sole discretion of Techni-Lux to repair or replace parts or
equipment. All shipping will be paid by purchaser. This warranty does not cover lamps, fuses, belts,
power semiconductors, relays, cleaning, standard maintenance adjustments or normal wear items or any
problem resulting from the following: improper wiring, incorrect voltage (including low or over voltage
conditions and lightning), abuse, misuse, improper maintenance or an act of God or damage resulting
from shipping. Warranty will be null and void if the product is altered, modified, misused, damaged, or
subjected to unauthorized repairs. Lamps are covered by relevant manufacturer warranty. This warranty
gives you specific legal rights, and you may also have other rights which vary from state to state. Any
liability for consequential and incidental damages is expressly disclaimed. No other warranty, expressed
or implied is made. Techni-Lux liability in all events is limited to, and shall not exceed, the purchase
price paid.
Returning equipment and Repairs: All returns must be accompanied by a Return Merchandise
Authorization (RMA) number and sent pre-paid. Contact the dealer or Techni-Lux directly to obtain an
RMA. The RMA number must be clearly listed on the shipping label. Due care must be exercised in
packing all merchandise to be returned. All repairs must be accompanied by a written explanation of the
claimed problem or error encountered. Techni-Lux is solely responsible for determining a product’s
eligibility for coverage under warranty. If returning for consideration of credit, all accessories and
documentation, original protective material and cartons must be included and the equipment, packing
and carton must be in new resalable condition. Credit for returned merchandise will be issued at the
lowest current price and is subject to a restocking fee of 20%. No returns accepted on discontinued
items. Techni-Lux is not responsible for merchandise damaged in transit and reserves the right to refuse
any return that is damaged by the carrier, not accompanied by a Return Authorization Number (RMA#) or
sent by freight collect.
Claims: All claims must be made within seven (7) days of receipt of merchandise. Any physical damage
must be reported to carrier upon receipt of merchandise.
Please record the following information for future reference:
Model Number: IL-TRACKER250S/1
Serial Number: ________________________________________
Dealer: ______________________________________________
Date of Purchase: ______________________________________
www.Techni-Lux.com
10779 Satellite Boulevard
Orlando, FL 32837
U.S.A.

4
Table of Contents
Specifications .............................................................................................................................5
Fixture Overview.......................................................................................................................5
Physical.....................................................................................................................................5
Lamp Source.............................................................................................................................5
Environmental...........................................................................................................................6
Electrical ...................................................................................................................................6
Control ......................................................................................................................................6
Optics........................................................................................................................................6
Gobo Size .................................................................................................................................6
Rigging......................................................................................................................................6
Unit Parts.....................................................................................................................................7
Unpacking ...................................................................................................................................8
Power...........................................................................................................................................9
Voltage Selection......................................................................................................................9
Lamp..........................................................................................................................................10
Lamp Installation.....................................................................................................................10
Lamp Alignment......................................................................................................................11
Mounting ...................................................................................................................................12
Data Link DMX-512 ...................................................................................................................13
Data Terminator......................................................................................................................13
Adapter 5-to-3 pin ...................................................................................................................13
Control Panel Menu..................................................................................................................14
Start Address............................................................................................................................14
DMX-512 Channels ...................................................................................................................15
CH 1-4 : Pan / Tilt Movement..................................................................................................15
CH 5 : Movement Speed Pan/Tilt..........................................................................................15
CH 6 : Control Reset/Lamp...................................................................................................16
CH 7 : Color Wheel...............................................................................................................16
CH 8 : Fixed Gobo Wheel.....................................................................................................17
CH 9 : Prism..........................................................................................................................17
CH 10 : Prism Rotation ...........................................................................................................18
CH 11 : Rotating Gobo Wheel.................................................................................................18
CH 12 : Gobo Rotation and Index...........................................................................................19
CH 13 : Effects – Zoom Frost UV............................................................................................19
CH 14 : Focus.........................................................................................................................19
CH 15 : Shutter .......................................................................................................................20
CH 16 : Dimmer ......................................................................................................................20
Photometric Charts ..................................................................................................................21
Installing Gobos........................................................................................................................22
Installing Rotating Gobos........................................................................................................22
Installing Fixed Gobos.............................................................................................................23
DMX-512 Background...............................................................................................................24
Maintenance..............................................................................................................................25
Troubleshooting .......................................................................................................................26
Wiring Diagram.........................................................................................................................27
Accessory Items.......................................................................................................................28

5
Specifications
Fixture Overview
•Pan range of movement: 530°
•Tilt range of movement: 280°
•High resolution 16 Bit Pan/Tilt movement for accurate positioning
•Pan/Tilt motor speed
•Consistent & auto correcting Pan/Tilt positioning
•Remote lamp on and off
•Remote reset
•Color wheel with 7 dichroic colors plus open
•Color wheel with continuous rotation for rainbow effect
•Static effect/gobo wheel with 3 gobos & 3 additional dichroic colors plus open
•3-facet rotating prism, variable speed in both directions
•Gobo wheel with 5 rotating, indexable and interchangeable gobos plus open
•Gobo wheel with continuous rotation
•Remote selection of zoom degrees: 15°, 18°, 21°, 24°, 26°
•Frost and UV blacklight effect
•Motorized focus
•Variable shutter for strobing effects and quick blackouts
•Motorized dimmer from 0 to 100%
•Control via DMX512 using 3 pin In/Out XLRs
•Uses 16 Channels of DMX
•Digital display for DMX addressing and fixture settings
•Ventilation via forced air
•Anti-reflective coated glass optics
•High efficiency coated glass Spherical Reflector
•Lamp: CSD250/2 or MSD250/2
•Luminous output: 18,000 Lux
Physical
Color Black
Width 17 in (43.2cm)
Depth 17 in (43.2cm)
Height 21 in (53.3 cm)
Weight 61 lbs (27.7 kg)
Gross Weight 73 lbs (33.1 kg)
Lamp Source
Lamp Type 250w Metal Halide Discharge
Base GY9.5
Lamps GE – CSD250/2 or Phillips – MSD250/2
Lamp Specs 250w, 3000 Hour, 8500°K Color Temp, 18000 Lumens
Ballast Type Magnetic

6
Environmental
Maximum ambient temperature 105°F (40°C)
Maximum exterior surface temperature 176°F (80°C)
Minimum distance to flammable surface 3.3ft (1m)
Minimum distance to illuminated surface 4ft (1.2m)
Electrical
Factory Setting 115v 60Hz
Selectable Voltages 100v / 115v / 208v / 220v @ 50 or 60Hz
Rated Power 500W, 4.1A @ 115v
Fuses 6.3A Time Delay (Slow) Size: 1¼” x ¼”
Control
Protocol USITT DMX512 (1990)
Channels 16
Pan / Tilt Resolution16 bit
Data I/O 3 Pin XLR (Cannon)
Modes Master / Slave / DMX
Optics
Reflector High efficiency coated glass Spherical.
Lenses Anti-reflective coated condenser system.
Zoom Stepped: 15°, 18°, 21°, 24°, 26°
Gobo Size
Gobo Rotating Outside Diameter 1.465” (37.2mm)
Image Diameter 1.181” (30mm)
Thickness Max 0.138” (3.5mm)
Gobo Fixed Outside Diameter 1.465” (37.2mm)
Image Diameter 1.181” (30mm)
Thickness Max 0.047” (1.2mm)
Rigging
Position Floor or Truss mount
Orientation Any
Mounting Points 2
Clamp Orientation Bracket: 0°, 90° Clamp: Any angle
Safety Point Eye Bolt

7
Unit Parts
POWER SWITCH
POWER SUPPLY T 3.15A@230V
T 6.3A@120V
LAMP:MSD 250/2
MSD 250
FUSE
1=GND
2=SIG.-
3=SIG.+
SERIAL DATA LINK
LIGHTING CONTROL PROTOCOL:DMX512
Serial number:
1 - Moving Head
2 - Yoke
3 - Carry Handle
s
4 - Base
Rear Panel
5 - Power Switch
6 - DMX Out
7 - DMX In
8 - Power Cord
9 - Fuse Holder
Front Panel
10 - Mode Button
11 - Enter Button
12 - Up Button
13 - Down Button
14 - Display

8
Unpacking
Immediately upon receipt, carefully unpack and inspect the fixture to verify that all parts are
present and have been received in good condition. If any parts appear damaged from shipping
or the shipping carton shows signs of mishandling, retain all packing material for inspection and
notify the shipper immediately. Save all original packing and carton. In the event that the
merchandise is to be returned, the original carton and packing must be used. The customer will
be billed for a new carton and packing if merchandise is received without the original carton and
packing. The plastic bag shipped with the fixture can be used to keep the fixture clean if stored
or installed in a temporarily dusty environment. Do not operate fixture with plastic bag in place.
Save Shipping Materials
The packing and carton are designed to provide the fixture with protection during
shipping. Save original packing and documentation for warranty, service and return
issues. Additional charges will be applied to return items not received in original or
incomplete packing.
Claims
Physical damage must be reported to the Freight Carrier or Shipping Company upon
receipt of merchandise. Damage incurred in shipping is the responsibility of the Freight
Carrier or Shipping Company. It is the customer's obligation in the event that
merchandise is received damaged caused by shipping to notify the Freight Carrier or
Shipping Company immediately. All other claims not related to damage incurred during
shipping must be made to the Dealer or Distributor within 7 (seven) days of receiving
merchandise.
Returns
Returned merchandise must be sent prepaid, in the original packing with a Return
Merchandise Authorization number (RMA) clearly listed on the shipping label. Items
sent by Freight Collect or without a RMA number will be refused. Call your sales person
and request a RMA prior to shipping. Be prepared to provide the model number, serial
number and a brief description of the nature of the return. Shipping damage resulting
from inadequate packaging is the customer’s responsibility. Customer will be charged
additional shipping charges to return products received in non original packing and or
cartons.

9
Power
Do not apply power to the fixture until input voltage setting and power source are verified.
For protection against electric shock, fixture must be connected to suitable earth ground.
Make sure fixture is cool and disconnected from power mains before any service.
The listed current rating is its average current draw under normal conditions. All fixtures must be
powered directly from a switched circuit. This fixture cannot be run on a rheostat or dimmer
circuit even if used solely for a 0% to 100% switching. Before applying power to a fixture, check
that the fixture’s input voltage matches the power source voltage. Consult a qualified electrician
if there are any concerns about proper connection to power.
Pin
Cable (EU) International
Brown
Light blue
ellow/Green
Y
Black
White
Green
Live
Neutral
Earth
L
N
Cable (US)
Voltage Selection
Make sure fixture is cool and disconnected from power mains before any service.
This fixture ships from the factory set for 115v 60Hz operation unless otherwise specified
or marked. Before accessing the Transformer Connection, make sure fixture is cool and
physically disconnected from power mains. Remove the metal cover that extends
across the base from the Power Input to the Display. It is held by 9 Phillips screws. One
connection must be moved to adjust input voltage and one to adjust Line Frequency.

10
Lamp
Make sure fixture is cool and disconnected from power mains before any service.
Do not touch the lamp glass with bare fingers. Wear eye protection when handling lamp.
When operating, always allow the lamp to cool at least 5 minutes before attempting to re-strike
the lamp. Not doing so can cause damage to the fixture and lamp. This fixture uses a 250w
Metal Halide Discharge lamp. Either a CSD250/2 from GE or a MSD250/2 from Phillips can be
fitted. Both lamps have an average rated life of 3000 hours. The lamp manufacturer determines
the rated lamp life under specific test conditions. Factors such as the number of strikes, lamp
orientation, line voltage and lamp temperature all affect the actual number of hours a lamp will
operate. Lamp temperature is the most controllable and with routine cleaning and maintenance,
can be kept in the optimal range to allow the maximum possible life. As Discharge lamps age, the
glass envelope becomes weaker increasing the chance of failure due to the high internal
pressures. Rupture could result in damage to the fixture and/or injure people nearby. Lamp
manufacturers state operating a lamp beyond its rated number of hours constitutes a considerable
risk for lamp rupture. Lamp manufacturers recommend lamps be replaced once the rated life of a
lamp has been reached.
Lamp Installation
1. Physically disconnect fixture from power mains.
2. Locate the Top Cover, loosen the 3
Fastening Screws and remove.
3. Locate the Lamp Cover, loosen the 2
Fastening Screws and remove. Do not
proceed until cover is cool.
4. Remove old lamp (if installed). Never
handle lamps with bare hands. Dispose of
lamp properly.
5. Insert new lamp into socket. Ensure lamp
is firmly and properly seated.
6. Visually align lamp, see Lamp Alignment,
before replacing covers.
7. Carefully replace Lamp Cover (2 screws)
and Top Cover (3 screws).
Top
Cover
Lam
p
Fastening
Screws
F
asten
i
ng
Screws
Lamp
Cover
Do not operate Fixture without covers!

11
Lamp Alignment
Due to slight variations between lamps it may be necessary to perform fine adjustments
to remove excessively dark or bright spots in the output field. The lamp holder is aligned
at the factory, large adjustments to the alignment will not be necessary. Excessively
bright spots can damage optical components.
1. Disconnect fixture from power and make certain lamp is cool.
2. Remove both the Top and Lamp covers (see Lamp Installation).
3. Turn Screw A located on the back plate of the Head, visually center the lamp
between the condenser lens and the reflector. Optimum distance between the
lamp and the condenser lens is 0.04”-0.06” (3/64”-1/16” or 1mm-1.5mm)
4. Turn Screw B, visually center the lamp horizontally to the lens.
5. After visually centering the lamp, replace both the Lamp and Top covers.
6. Apply power to the fixture. CAUTION: Double check for Lamp cover is installation.
7. Using a controller, strike the lamp with shutter and dimmer to 100% and project an
open white beam on a flat neutral colored surface.
8. Use Slight adjustment of Screw B ONLY to optimize the hot spot of the beam.
9. Extreme caution must be utilized when adjusting Screw A. The lamp must not
come to reset against either the front lens or reflector. If the edges of the beam are
brighter than the center, the lamp is too close to the reflector. If the center of the
beam is much brighter than the edges, the lamp is too close to the condenser lens.
Again, the lamp must not come to reset against either the front lens or reflector.
1-1,5mm
Optimum distance
Screw B
Screw A
Correct
WARNING!
Lamp is hot! Risk of fire! Protect hands and eyes.
Wait at least 15min. Before opening the covers
and removing lamp from the fixture.
Minimum distance to lighted object:
Maximum room temperature t=45¡
Minimum distance from flammable material d=0.5m.
Exterior surface temperature T=80¡.
Not for domestic use.
Be sure that the lamp
bulb never touch the lens
Disconnect the fixture from AC power
before re-lamping.
A
B
A
djust lamp position by turning screws and
Incorrect
Contact

12
Mounting
Always consult a qualified professional when rigging. This fixture may be placed on any flat
surface or truss that is capable of safely supporting the weight. When selecting a mounting
position, take into consideration access for routine maintenance. This fixture may be mounted in
any position provided there is adequate room for movement and ventilation. Mount the fixture
securely using two mounting clamps and a safety cable. An Eye Bolt is provided for safety
attachment. Safety cables must always be attached to the fixture. Do not use handles as
secondary mounting points. Do not mount in a place where the fixture will be exposed to rain,
high humidity, extreme temperature changes or restricted ventilation. Do not obstruct the vents
or fans. Keep fixture a minimum of 3.3ft (1m) from flammable materials.

13
Data Link DMX-512
For data, this fixture uses 3 pin XLR (Cannon) type connectors and shielded twisted pair cable
approved for EIA-422/EIA485 use. Fixtures are connected in Daisy Chain topography with only
one data source and no branching is allowed. Systems using 5 pin DMX interfaces can be
accommodated by purchasing 3-to-5 pin adapters or building adapter cables.
Data Terminator
A Data Terminator can be connected to the DATA OUT connection
of the last fixture to reduce the effects of noise in the signal; it is not
required for all installations. To make a Data Terminator, connect a
120-ohm ¼ watt resistor across pin 2, Data Negative (S-) and pin 3,
Data positive (S+). A qualified technician can determine if a Data
Terminator is needed.
Adapter5-to-3 pin
Numbers designating each pin can be found on connectors. Converting between the two
XLR types is done in a pin-to-pin fashion. Connect the shields to pin 1, then connect pin
2 to pin 2 and pin 3 to pin 3. This is true for converting either 5 to 3 pin or 3 to 5 pin
regardless of either connector’s gender. Pins 4 and 5 are not used on the 5 pin XLR
connectors.
DMX-OUT
1
2
3
- Ground
- Signal (-)
- Signal (+)
X
LR Connector - Socket:
DMX-IN
1
2
3
- Ground
- Signal (-)
- Signal (+)
XLR Connector - Plug:
5 Pin XLR (Plug)
Pin 1: GND(Sheild)
Pin 2: Signal(-)
Pin 3: Signal(+)
Pin 4: N/C
Pin 5: N/C
3 XLR (S )
Pin 1: GND(Sheild)
Pin 2: Signal(-)
Pin 3: Signal(+)
Pin ocket
5 Pin XLR (Socket)
Pin 1: GND(Sheild)
Pin 2: Signal(-)
Pin 3: Signal(+)
Pin 4: N/C
Pin 5: N/C
3 XLR (Plug)
Pin 1: GND(Sheild)
Pin 2: Signal(-)
Pin 3: Signal(+)
Pin
DMX512
120
Ω

14
Control Panel Menu
Use the fixture’s Control Panel to access the Control Menu. The MODE Key moves between
options, UP/DOWN selects the Action of the option and ENTER confirms the selection. Settings
are stored and recalled on subsequent power cycles.
Start Address
The Start Address of a fixture is set using the “Addr” mode in the Control Panel Menu. Consult
the manual of the system’s DMX512 controller to select a desirable addressing scheme before
addressing fixtures. Each fixture connected to the DMX-512 data link requires a Start Address
to indicate the first DMX channel containing data designated for that fixture, see DMX-512
Background. Valid Start Addresses range from 1 to 512. Fixtures requiring more than one
channel for control will read subsequent channels up to the total number of channels required.
A fixture requiring five (5) channels of DMX, set to a Start Address of eleven (11), would read
data from channels: 11 and 12, 13, 14, 15. The next logical Start Address would be channel
16. Because all fixtures see the same data, fixtures may be set to any address without concern
to order in the DMX-512 chain or physical location. Choose a Start Address so the channels
used do not overlap with other fixtures. In some cases, it may be desirable to set two or more
same type fixtures to the same Start Address. In this case, the fixtures will be slaved together
and respond to the same data.
Example Select Start Addresses for 4 fixtures each requiring 16 channels of DMX.
Since these are the first fixtures added to the system, the first unit will be set to Start
Address=1. This fixture occupies DMX channels 1 thru 16. The next DMX channel
available for a Start Address is found by adding the previous fixture’s Start Address to its
channel requirement: 1+16=17. DMX channel 17 is the next available Start Address. In
this example, to maximize channel usage no empty channels are left between fixtures so
the second Start Address is set to DMX channel 17. The second fixture occupies DMX
channels 17 thru 32. Repeat the process for the remaining two fixtures: 17+16=33 and
33+16=49. Therefore, the four 16 channel fixtures have Start Addresses of 1, 17, 33 and
49. Repeat the technique once more for the next free channel in the system, 49+16=65.
Channels 65 thru 512 are available for expansion of the system.
Mode Function Action
NO = Not Inverted
YES = Inverted
Tilt movement direction Invert
DMX Start Address
Fixture Reset
Color Wheel Movement Mode
Operating Mode
DMX512 mode
Automatic
Slave mode
Lamp ON/OFF
Software Version
Error: Lamp didn’t strike, Hot
Error: Lamp didn’t strike,
Service
NO = Not Inverted
YES = Inverted
Selectable 1 to 496
NO = Default
YES = Initiate Reset
NO = Linear
YES = Indexed
NO = Lamp OFF
YES = Lamp ON
View Software Version
See Troubleshooting
See Troubleshooting

15
DMX-512 Channels
The Tracker 250 Spot requires 16 channels of DMX.
Channel Function
1 Pan Coarse Movement
2 Pan Fine Movement
3 Tilt Coarse Movement
4 Tilt Fine Movement
5 Movement Speed Pan/Tilt
6 Control Reset/Lamp
7 Color Wheel
8 Fixed Gobo Wheel
9 Prism
10 Prism Rotation
11 Rotating Gobo Wheel
12 Gobo Rotation & Index
13 Effects – Zoom Frost UV
14 Focus
15 Shutter
16 Dimmer
CH 1-4 : Pan / Tilt Movement
The Pan and Tilt motors use a position feedback system. If the position of either is
disturbed, the fixture will correct automatically. The Pan and Tilt Menu Modes can be
used to alter the default direction of movement. Movement speed is either automatically
determined by the fixture or manually set using Channel 5 Pan/Tilt Movement Speed.
Pan range is 530° of movement. Tilt range is 280° of movement.
CH 1 – Pan Coarse Movement (530°)
CH 2 – Pan Fine Movement
CH 3 – Tilt Coarse Movement (280°)
CH 4 – Tilt Fine Movement
DMX Value Function
0 – 255 Movement - Minimum to Maximum
CH 5 : Movement Speed Pan/Tilt
When set to zero (0) the fixture automatically determines the Pan/Tilt speed. Other
values are used to set the movement speed manually.
CH 5 – Movement Speed Pan/Tilt
DMX Value Function
0 Auto Speed
1-255 Fixed Speed - Fast to Slow

16
CH 6 : Control Reset/Lamp
Fixture reset and Lamp On/Off control is accessed from a single channel. The “No
Function” values provide buffer zones between functions and are not values to which the
channel should be set. In the case of noisy faders or unintentional movement, the buffers
will prevent slight variations in value to toggle Lamp states or start a fixture Reset.
CH 6 – Control Reset/Lamp
DMX Value Function
0-127 No Function
128-139 RESET then Lamp ON (3 second delay)
140-229 No Function
230-239 Lamp OFF (3 second delay)
240-255 No Function
CH 7 : Color Wheel
The Color Wheel holds 7 solid colors plus open. These color filters can be used in
conjunction with the Dichroic Rotating Gobos and Fixed Gobo color filters to create many
color combinations. A Rainbow Color Scroll effect can also be created. In the Control
Panel Menu, the COL1 option will change the behavior of the Color Wheel from Indexed
to Linear. In Linear mode, the fixed color indexes are removed and colors can be
positioned variably.
CH 7 – Color Wheel
DMX Value Function
0-7 Open
8-15 Open / Red
16-23 Red
24-31 Red / Yellow
32-39 Yellow
40-47 Yellow / Magenta
48-55 Magenta
56-63 Magenta / Green
64-71 Green
72-79 Green / Orange
80-87 Orange
88-95 Orange / Blue
96-103 Blue
104-111 Blue / Pink
112-119 Pink
120-127 Pink / Open
128-137 Color Scroll Pause
138-255 Rainbow Color Scroll – Slow to Fast

17
CH 8 : Fixed Gobo Wheel
The Fixed Gobo Wheel contains 3 fixed gobos and three color filters. Using both Gobo
wheels and varying the Focus can create many interesting effects. Each gobo is
mounted in a frame that can easily be removed. Gobos can easily be rearranged from
the factory default arrangement shown. For more information, see Installing Gobos.
CH 8 – Fixed Gobo Wheel
DMX Value Function
0-36 Open
37-73 Fixed Gobo 1
74-110 Fixed Gobo 2
111-147 Fixed Gobo 3
148-184 Color Filter Lt. Orange
185-221 Color Filter Lt. Purple
222-255 Color Filter Lt. Blue
CH 9 : Prism
The Prism effect uses a 3 facet prism to create multiple beams. Using channel 10, the
effect can be rotated in either direction at variable speeds.
CH 9 – Prism
DMX Value Function
0-127 Open
128-255 Prism
0
1
2
3
4
5
6

18
CH 10 : Prism Rotation
Controls the rotation of the Prism.
CH 10 – Prism Rotation
DMX Value Function
0-4 Prism Rotation Stop
5-127 Prism Rotation Forward – Slow to Fast
128-132 Prism Rotation Stop
133-255 Prism Rotation Reverse – Slow to Fast
CH 11 : Rotating Gobo Wheel
The Rotating Gobo Wheel contains 5 replaceable gobos, 2 metal and 3 glass. The Gobo
Rotation & Index channel 12 controls the position and rotation of the gobos. Using both
Gobo wheels and varying the Focus can create many interesting effects.
CH 11 – Rotating Gobo Wheel
DMX Value Function
0-31 Open
32-63 Rotating Gobo 1 (Glass – Waffle Texture)
64-95 Rotating Gobo 2 (Glass – Pink Pin Wheel)
96-127 Rotating Gobo 3 (Glass – Blue Field White Dots)
128-159 Rotating Gobo 4 (Metal)
160-223 Rotating Gobo 5 (Metal)
224-228 Gobo Scroll Pause
229-255 Rotating Gobo Scroll – Slow to Fast
0
1
2
3
4
5

19
CH 12 : Gobo Rotation and Index
Rotating gobos can be rotated in either direction or indexed to a fixed orientation.
CH 12 – Gobo Rotation and Index
DMX Value Function
0-60 Indexed – 0 to 540°
61-158 Rotation – Slow to Fast
159-255 Rotation Reverse – Slow to Fast
CH 13 : Effects – Zoom Frost UV
The 5 step zoom feature of this fixture has two modes. The Focus Correction mode will
make adjustments to help keep the image in focus when changing beam angles. The No
Focus Correction mode will not adjust the focus when changing beam angles. The
standard projection from this fixture is a hard edge beam. Modification of the beam can
be done with a Frost Effect, creating a very wide diffused beam with a soft edge. A UV
color filter effect is also included.
CH 13 – Effects – Zoom Frost UV
DMX Value Function
0-31 15° Beam Angle – No Focus Correction
32-47 18° Beam Angle – No Focus Correction
48-63 21° Beam Angle – No Focus Correction
64-79 24° Beam Angle – No Focus Correction
80-95 26° Beam Angle – No Focus Correction
96-111 15° w/ Frost
112-127 15° w/ UV Color Filter
128-159 15° Beam Angle – Focus Correction
160-175 18° Beam Angle – Focus Correction
176-191 21° Beam Angle – Focus Correction
192-207 24° Beam Angle – Focus Correction
208-223 26° Beam Angle – Focus Correction
224-239 15° w/ Frost
240-255 15° w/ UV Color Filter
CH 14 : Focus
The Focus is used to vary the focal point of the projection. Using both Gobo wheels and
varying the Focus can create many interesting effects.
CH 14 – Focus
DMX Value Function
0-255 Focus – Far to Near

20
CH 15 : Shutter
The Shutter functions in three modes. Standard Strobe Effect where the shutter
Opens/Closes at a fixed rate. Pulse Strobe Effect where the Open and Close speeds are
different. Random Strobe Effect runs the shutter at irregular intervals.
CH 15 – Shutter
DMX Value Function
0-31 Closed (Black Out)
32-63 Open
64-95 Strobe Effect - Slow to Fast
96-127 Open
128-159 Pulse Strobe Effect - Slow to Fast
160-191 Open
192-223 Random Strobe Effect
224-255 Open
CH 16 : Dimmer
The dimmer is used to vary the intensity of the beam from full open to dark.
CH 16 – Dimmer
DMX Value Function
0-255 Intensity - Dark to Full Open