TEKA ILLUMINATION KMJ User manual

THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF B-K LIGHTING, INC. AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR SELL ANYTHING IT MAY
DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF B-K LIGHTING, INC. IS STRICTLY FORBIDDEN.
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE THESE INSTALLATION INSTRUCTIONS
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX [phone]
www.bklighting.com • [email protected]
RELEASED
7-26-12
REFERENCE NUMBER
INS001291.1
STAKE MOUNT JUCTION BOX
Low Voltage /
Warning
TOOLS
NEEDED:
By Others
5/64” Allen Wrench
Wire connectors
(recommended silicone filled wire connectors)
IMPORTANT LISTINGS AND CERTIFICATIONS
· Suitable for wet locations
Fixture is specified
separately
1. Use 5/64” Allen wrench loosen three (3) #8-32
stainless steel set screws (do not remove set screws
from canopy). Remove canopy from stake.
2. Mount fixture onto canopy by securing 1/2” NPS
stem with provided locknut.
KMJ- Stake Mount
Junction Box™
Anchor Base
Canopy
• Product must be installed by a qualified person in a manner
consistent with its intended use and in compliance with the
National Electrical Code, Canadian Electrical Code, and all Local
and Provincial Codes.
• Follow product label information and instructions.
• Qualified Personnel must perform all servicing or relamping of
this product.
• Before wiring to power supply and during servicing or relamping,
turn off power at fuse or circuit breaker before service.
• The use of accessory equipment not recommended by the
manufacturer or installed contrary to instructions may cause an
unsafe condition. The use of damaged components may cause
an unsafe condition and void product warranty.
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE ALL SAFETY
AND INSTALLATION INSTRUCTIONS
• Do not block light emanating from product in whole or part,
as this may cause an unsafe condition.
• Never operate the fixture with missing or damaged lens.
Lens must be cleaned on regular basis.
• Entire fixture may become extremely hot. Do not touch hot
lens or fixture body. Do not touch the lamp at any time. Use
a clean, dry, soft cloth to handle the lamp. Oil from skin may
damage the lamp and cause it to rupture.
• Replace lamp only with correct wattage and type of lamp
marked on fixture label.
• All gaskets, o-rings and sealing surfaces must be kept clean
during installation and service; failure to do this may cause an
unsafe condition and void product warranty.
INSTRUCTIONS PERTAINING TO
A RISK OF FIRE, OR INJURY TO
PERSONS IMPORTANT SAFETY
INSTRUCTIONS
Lighted lamp is HOT!
WARNING - To reduce the risk of FIRE OR INJURY TO PERSONS:
Turn off/unplug and allow to cool before replacing lamp.
Lamp gets HOT quickly! Contact only switch/plug when
turning on.
Do not touch hot lens, guard, or enclosure (see diagram/
picture).
Keep lamp away from materials that may burn.
Do no touch the lamp at any time. Use a soft cloth. Oil
from skin may damage lamp.
Do not operate the luminaire fitting with a missing or
damaged shield.
SAVE THESE INSTRUCTIONS
Stainless Steel
Set Screw
Pointed edges are sharp

40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX [phone]
www.bklighting.com • [email protected]
IMPORTANT SAFETY INFORMATION LISTED ON REVERSE
READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS
RELEASED
7-26-12
REFERENCE NUMBER
INS001291.1
PROJECT:
TYPE:
STAKE MOUNT JUCTION BOX
Low Voltage /
7. Insert fixture according to desired lighting plan.
4. Make two connections from remote 12V
transformer to fixture source leads using proper
wire connectors (By Others). See wiring diagram.
NOTE: Contractor responsible for executing
water tight splice.
Wiring diagram.
120V 12V
Fixture
COM
Remote
Transformer
COM
3. Pull low voltage wiring from remote 12V
transformer (By Others) through the center of
the anchor base and stake assembly.
NOTE: Allow sufficient excess of low voltage
direct burial cable to accommodate seasonal
planting schedule.
5. Place canopy onto stake and press firmly until
the two pieces are fully seated.
6. Tighten the three (3) #8-32 stainless steel set
screws on canopy with 5/64” Allen wrench.
Warning: Do not over tighten set screw.
Doing so will compromise O Ring seal and will
void warranty.