Teka intra Icon ICSE User manual

GRINDED
Art. no.
GTIN
ICSE
7055570016183
Overall dimension in mm 125 x 240 x 105
Material AISI 304
Material thickness in mm 1,0
Installation height in mm 1350mm til topp
Description
ICON electrical, touch ree soap dispenser in stainless
steel. Delivered with a 0,9 litre soap container or
re ill. Run by 4 x 1,5 V AA batteries.
Installation
Check the ollowing be ore installation:
There must be su icient space above the dispenser
or inserting the key and to open up the cover with the
key. In addition, there must be at least 200mm
clearance to the counter top.
Above stainless steel wash basin, the minimum
distance is 300mm.
See instructions or urther assembly.
Icon ICSE
FDV Revision 20140319www.intra-teka.com

Installation ICSE
MOUNTING INSTRUCTION
Box Contents:
* Soap dispenser complete with cover control unit
and soap container with dispenser spout.
* Key
Additional:
* 4 pcs Alkaline batteries 1 5V AA (Not included)
Use the back plate as template for placement of
drilling holes. Open the soap dispenser with supplied
key. Remove the soap container by lifting up the
spring-loaded cover that keeps the spout in place and
lift out the container and spout. Remove the control
unit for the pump as well. Fix four monting screws
suitable for the wall construction in the back panel
and attach it to the wall. Reinstall the controller. fill
the soap container and and place the soap container
in its place above the control unit. After cleaning the
tank and upon initial installation the spout must be
filled with soap. Squeeze the spout until it is
completely filled with soap. Make sure that the spout
is in tension between the upper and lower part of the
control unit by placing by placing the plastic ring by
the spout on the lower side of the control unit when it
is inserted in place behind the cover. Close the
spring-loaded cover which keeps the spout in place.
Open the battery door on the side of the control unit
(right side) and insert four batteries 1 5V AA size. Test
that the soap dispenser works by pressing and
holding down the blue activity button on the bottom
of the disenser. This will initiate a blink 3-4 times from
the blue led light. Close the battery compartment
cover and lock the dispenser. Remove the protection
on the spout and place your hands under the soap
outlet and repeat sometimes until soap comes out.
Make sure everything is working correctly.
Selection of soap
The soap must be free of the following chemicals:
Chlorine and alcohol and iodine compounds. The
viscosity of the soap must be within the given range
and pH should be neutral.
Refill of soap: Soap can be refilled by taking out the
soap container open the lid on the top clean the
tank refill soap and press the rubber spoat
sometimes so that the tube is filled with soap. Put
soap container in place of the control unit.
MAINTENANCE:
INTRA PRODUCTS OF STAINLESS STEEL
Several of our products are delivered entirely or
partly covered with plastic wrapping. This wrapping
protects the products during transport. This wrapping
must be removed before using the products.
In order for your Intra stainless steel product AISI304
to retain its original quality and appearance we
recommend regular cleaning. Use mild soap or
cleaning products specifically designed for stainless
steel and clean water. Then wipe the surface with a
dry cloth.
Never use detergents containing chlorine iodine
fluoride or abrasives on stainless steel. Also avoid
contact with acid solutions and other substances
incompatible with stainless steel. Remember that
food and skin care products may contain such
substances e.g. ketchup juice salt certain cleansers
nail polish etc. Promptly remove spills of such
products.
Observe the following:
* Do not allow water or other liquid to dry in. This is
to avoid staining the surface.
* Even though stainless steel can withstand harsh
treatment it can easily be scratched by sharp objects.
For products with normal polished (brushed) finish
this will be very visible when the product is new but
after a period of use this will be negated as the steel
loses its lustre. For products with satin and polished
finishes the scratches will always be visible. Never
use scouring powder or steel wool on stainless steel.
In addition to scratching the steel wire wool will
leave behind small particles that may develop into
rust spots which over time may corrode the steel.
* Stainless steel must not come into contact with or
be in environments containing chlorine solutions for
long periods of time.
* Silver polish causes stains which cannot be
removed.
2
FDV Revision 20140319www.intra-teka.com

Maintenance ICSE
TECHNICAL INFORMATION
Soap viscosity: 1-3000 MPas
Tank si e: 0,8 L
Battery: 4 pcs Alkaline 1,5V AA batteries (not
included)
Battery life time: 10.000 cycles or 1 year.
Soap consumption per cycle: 0,034 - 0,051 ml
Delay: 500-1k msec
Functional area for sensor: 60±38 mm
Operative room temperature: 5-40°C
Operating motde: Starts automatically when
triggering sensorType of pump: Self-contained valve
o le
MAINTENANCE OF SOAP DISPENSER
The soap container must be cleaned before every
refill- Ensure that there is no solidified soap on the
spout, the sensor, on the lid of the soap tank and that
the vent hole in the lid is open. the control unit must
never be washed under running water or immersed
in water. Use a damp cloth for cleaning.
DIAGNOSIS OF BATTERY
Open the dispenser and remove the soap tank from
the controller.
1. Press on the little blue button under the control unit
and hold it.
2. Observe the LED indicator light. 3-4 blinks indicate
battery capacity
3. If the Led indicator light continues to blink, it's time
to replace the batteries. Replace all batteries at the
same time.
TROUBLESHOOTING
IT DOES NOT COME OUT SOAP:
a) Check if it is solidified soap or other dirt on the
spout and sensor plate. Wash well to make it clean.
b) Check the soap in the container. Refill if necessary.
c) Check the batteries.
d) Check soap quality and that this is within the
requirements of applicable soap. Clen the container
and fill with the correct soap.
e) Check that the spout of the dispenser is in tension
in the control unit. Romove and place again if this is
not the case.
f) Check that there are no reflections that confuse the
sensor. Remove this if necessary-
g) Check that the protection of the spout is removed
(after installation).
Battery LED indicator is not blinking:
The cover of the dispenser must be open for the LED
indicator to appear. Replace battery.
Battery LED indicator is blinking continually:
If the led indicator does not stop blinking after 3-4
flashes, it is time to change the batteries. Replace all
at once.
It comes to small dose of soap:
Remove the soap container and wash container,
spout and lid. Ensure that the hole in the lid is open
and also that the spout is open. Then fill the container
with new soap of the right quality before the
container is repositioned. Check tha the spout is in
tension and tighten between the upper and lower part
of the control unit and that the spring-loaded door is
closed.
It is leaking soap from the bottom of the dispenser:
Check if there is a hole/crack in the soap container or
pipe to the spout. Replace tank if necessary
3
FDV Revision 20140319www.intra-teka.com