Tektronix MTS4EA User manual

Instructions
MTS4EAUP
License Upgrade for
MTS4EA Compressed Video ES Analyzer
075-0894-00
*P075089400*
075089400
www.tektronix.com

Copyright ©Tektronix, Inc. All rights reserved. Licensed software products are owned by Tektronix or its subsidiaries or
suppliers, and are protected by national copyright laws and international treaty provisions.
Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication supercedes
that in all previously published material. Specifications and price change privileges reserved.
TEKTRONIX and TEK are registered trademarks of Tektronix, Inc.
Contacting Tektronix
Tektronix, Inc.
14200 SW Karl Braun Drive
P.O. Box 500
Beaverton, OR 97077
USA
For product information, sales, service, and technical support:
HIn North America, call 1-800-833-9200.
HWorldwide, visit www.tektronix.com to find contacts in your area.

MTS4EA License Upgrade Instructions 1
Kit Description
This document describes how to perform the following upgrades on the software
key (dongle) for the Tektronix MTS4EA Compressed Video ES Analyzer:
HPermissions upgrade (add options to existing software)
HFloating license upgrade (add users to existing floating license)
HNode-locked to floating license upgrade (upgrade from single machine
license to single floating license)
An overview of the upgrade process is described on the following page.
Kit Parts List
Quantity Part number Description
1EA 075-0894-00 INSTRUCTIONS; MTS4EAUP LICENSE UPGRADE
1EA N/A FLOPPY DISKETTE, 3.5 INCH DOUBLE SIDED, 1.44 MB;
MTS4EA LICENSE UPGRADE

Kit Description
2MTS4EA License Upgrade Instructions
Upgrade Process Overview
Listed below are the high-level actions required for the various MTS4EA
upgrade scenarios. If you have upgrade problems, refer to Troubleshooting the
License Upgrade Process on page 15.
To upgrade from MTS4EA v3.0 to v4.0 or higher, perform the steps described in
Options Permissions Upgrade Procedure startingonpage3.
To upgrade from MTS4EA v4.0 to v4.x or higher, perform the steps described in
Options Permissions Upgrade Procedure startingonpage3.
To upgrade from a node-locked license (single license for a single machine) to a
single-user floating license, do the following:
HPerform the steps described in Options Permissions Upgrade Procedure
startingonpage3.
HRead the upgrade process described in User License Upgrade starting on
page 5.
HPerform the steps described in Node-locked to Floating License Upgrade
Procedure startingonpage10.
NOTE. If you want to upgrade from a node-locked license to a multiple-user
floating license, you must first upgrade your node-locked license to a single-user
floating license. After you upgrade to a single-user floating license, you can then
upgrade to a multiple-user floating license.
To upgrade from a single-user floating license to a multiple-user floating license,
do the following:
HPerform the steps described in Options Permissions Upgrade Procedure
startingonpage3.
HRead the upgrade process described in User License Upgrade starting on
page 5.
HPerform the steps described in Floating License Upgrade Procedure starting
on page 6.
Upgrading from v3.0
to v4.0 or Higher
Upgrading from v4.0 to
v4.x or higher
Upgrading from
Node-locked License to
Single-user Floating
License
Upgrading from
Single-user Floating
License to Multiple-user
Floating License

MTS4EA License Upgrade Instructions 3
Options Permissions Upgrade
These instructions are for personnel who are familiar with servicing the product.
If you need further details refer to the appropriate product manual. Contact your
nearest Tektronix, Inc., Service Center for installation assistance.
NOTE. Each MTS4EA software key (dongle) contains two sets of permissions:
one for the enabled MTS4EA options, and another for the user licenses. Since
separate processes are used to upgrade the options permissions and the user
licenses stored in the dongle, you can upgrade the options permissions and the
user licenses in any order.
Options Permissions Upgrade Procedure
The software key (dongle) stores the permissions for the enabled MTS4EA
options. The options permissions are upgraded using an update program and an
encrypted data file. Tektronix provides these files either by floppy disk or
CD-ROM with this kit, or by email.
Perform the following steps to upgrade the MTS4EA options permissions:
CAUTION. To prevent an upgrade failure, your computer or Tektronix MPEG
instrument must have the associated MTS4EA software key (dongle) installed.
Be sure that the dongle you are updating is the one you specified in the upgrade
order. The upgrade data file can be applied to the dongle only one time and it
will work only with the dongle specified at the time you ordered the upgrade.
1. If you received your upgrade files via email proceed to step 2. Otherwise,
insert the floppy disk or CD-ROM supplied with this kit into the appropriate
drive on your computer or Tektronix MPEG instrument.
2. Copy the upgrade files from the floppy disk or CD-ROM, or from the email,
to any directory on your computer or Tektronix MPEG instrument.

Options Permissions Upgrade
4MTS4EA License Upgrade Instructions
CAUTION. If the DESkey server is installed and running on the computer or
Tektronix MPEG instrument, you must stop the server service before you run the
executable file in step 3 below. If you do not stop the service, you will get an
error message when you attempt to run the file.
To stop the server service, open the Control Panel (Windows Start > Settings >
Control Panel) and select the DESkey icon, which opens the DESkey Configura-
tion dialog box. In the dialog box, select the Networking tab. Click the Stop
button if the server service is running. The server button will say Start when the
service is not running.
3. From the directory where you copied the upgrade files, run the following
executable file: remoteupdate.exe. The executable file will then use the
accompanying data file to securely change the contents of the dongle
memory to include any new options.
4. If necessary, remove the floppy disk or CD-ROM from the computer or
Tektronix MPEG instrument.

MTS4EA License Upgrade Instructions 5
User License Upgrade
The instructions on the following pages describe how to perform the license
upgrades listed below:
HFloating License Upgrade. Adds more user licenses to an existing floating
license.
HNode-locked to Floating License Upgrade. Converts a node-locked (single
machine) license to a single-user floating license.
User License Upgrade Process
The activities listed below are required to perform the user license upgrade:
1. You create a Customer Update Request File (CURF) and send that file to
Tektronix. The CURF is specific to the dongle on your existing product.
NOTE. The instructions for creating the CURF are described in Generating a
Customer Update Request File (CURF) starting on page 12.
2. Tektronix uses the CURF to create a License Upgrade File (LUF).
3. Tektronix sends you the LUF either on floppy disk or CD-ROM, or by
email.
NOTE. When you receive the upgrade files from Tektronix, you must copy the files
to a single directory on the hard drive of the client machine containing the
installed MTS4EA Compressed Video ES Analyzer used to create the CURF.
4. You apply the LUF to the dongle using the DESkey configuration utility.
NOTE. The instructions for applying the LUF are described in Floating License
Upgrade Procedure starting on page 6.
When the dongle has been upgraded, the LUF will become obsolete.

User License Upgrade
6MTS4EA License Upgrade Instructions
Floating License Upgrade Procedure
Perform the following steps to add user licenses to an existing floating license
dongle:
1. If necessary, copy the upgrade files from the floppy disk or CD-ROM, or
from the email, to a single directory on the hard drive of the client machine.
NOTE. The client machine must contain the installed MTS4EA Compressed Video
ES Analyzer that was used to create the CURF.
2. Ensure that the dongle is installed on the License Server.
3. From the client machine, open the control panel (Start > Settings > Control
Panel).
4. Open DESkey application. In the DESkey Configuration dialog box, select
the Networking tab. The server machine should be listed in the upper panel.
5. Verify that the server service is running. As shown below, the server button
will say Stop when the service is running. If the server button says Start,
click the button to start the service.

User License Upgrade
MTS4EA License Upgrade Instructions 7
6. Select the Monitor button to display the DK2 Network Server Remote
Monitor dialog box.
7. Highlight the server machine in the server list (upper panel) and click the
Admin button. Enter the required password. The default is “deskey”.
8. If the password is correct, the DK2 Network Server dialog box is displayed.
Select the License Request tab.

User License Upgrade
8MTS4EA License Upgrade Instructions
9. Press the Load from File button and locate the License Upgrade File (LUF)
on the hard disk. The upload is complete when data is displayed in the
License Update window.
10. Press the Send Update button to send the LUF to the server.

User License Upgrade
MTS4EA License Upgrade Instructions 9
11. Close the DK2 Network Server dialog box.
Note that the number of licenses available is displayed in the lower half of
the DK2 Network Server Remote Monitor dialog box.
12. Close all dialog boxes.
The floating license upgrade is now complete.

User License Upgrade
10 MTS4EA License Upgrade Instructions
Node-locked to Floating License Upgrade Procedure
You will need to perform the following steps to convert a node-locked dongle to
a floating license dongle:
HInstall and configure the license server
HGenerate the Customer Update Request File (CURF)
HInstall the License Update File (LUF)
Perform the following steps to install and configure the license server:
1. Select a server machine that will host the dongle (currently located on the
client machine).
NOTE. A client machine can also be set up as a server machine.
2. Move your existing MTS4EA dongle from the client machine to the server
machine. Install the dongle either on the USB port or on the parallel port of
the server machine, depending on the type of dongle.
3. Perform one of the following two actions:
HIf your current version of the MTS4EA software is 4.0 or higher, insert
the MTS4EA software installation CD-ROM (Tektronix part number
063-3824-xx) that was provided with your MTS4EA software into the
CD-ROM drive on the server machine.
HIf your current version of the MTS4EA software is 3.0, or you do not
have the MTS4EA v4.0 CD-ROM, contact Tektronix technical support
to obtain the program file used in step 5 below (dnsrv32.exe). You will
not be able to continue the upgrade process without this file.
NOTE. When the CD-ROM is inserted, the MTS4EA setup screen will be
displayed. Click the Close button at the bottom of the window to terminate the
MTS4EA installation program.
4. Using Windows Explorer, locate and open the DES directory on the
CD-ROM.
5. From the DES directory, run the program dnsrv32.exe. During the installa-
tion process, accept the default entries.
6. Reboot the server machine if requested to do so at the end of the installation
process.
Installing and Configuring
the License Server

User License Upgrade
MTS4EA License Upgrade Instructions 11
7. Open the Control Panel (Windows Start > Settings > Control Panel) and
select the DESkey icon. This will open the DESkey Configuration dialog
box, the first two tabs of which are shown below (the version numbers
shown near the bottom of the dialog box may vary).
NOTE. For the server installation, the DK2/DK38 tab and the top half of the
Networking tab can be ignored; these refer to the client installation that shares
the same configuration dialog.

User License Upgrade
12 MTS4EA License Upgrade Instructions
8. In the DESkey Configuration dialog box, select the Networking tab.
9. The field at the bottom labeled Server Port Number shows the port to be
used for communication with any clients; the default value is 3029. Click the
OK button to finish.
NOTE. Depending on the policy of your IT department, port 3029 may be blocked
by the network firewall. If this is true, perform the following steps:
1. Consult your network administrator for another unrestricted port.
2. Enter the new port number in the DESkey Configuration dialog box and
click the Apply button.
3. If you get a prompt asking about restarting the server, select Yes. This will
stop and start the Network Server Service using the new port.
4. When the port has been applied, click the OK button to finish. This restarts
the license server but does not cause the server to reboot.
Perform the following steps to generate a Customer Update Request File
(CURF) to send to Tektronix:
1. From the client machine, open the Control Panel (Windows Start > Settings
> Control Panel) and select the DESkey icon. This will open the DESkey
Configuration dialog box.
2. In the DESkey Configuration dialog box, select the Networking tab. The
server machine should be listed in the upper panel.
Generating a Customer
Update Request File
(CURF)

User License Upgrade
MTS4EA License Upgrade Instructions 13
3. Select the Monitor button to display the DK2 Network Server Remote
Monitor dialog box.
4. Highlight the server machine in the server list (upper panel) and click the
Admin button.
5. Enter the required password. The default password is “deskey”.
6. If the password is correct, the DK2 Network Server dialog box is displayed.
Select the License Request tab as shown below.

User License Upgrade
14 MTS4EA License Upgrade Instructions
7. Enter the required number of licenses in the requested edit box. The number
of requested licenses plus the current number of licenses cannot exceed 255.
8. Click the Get Request button to generate the data for the Customer Update
Request File (CURF). The generated data is shown in the panel next to the
button and the Save to File button is enabled.
9. Click the Save to File button and select a location and filename for the data.
Any file name can be used, but the file must have a “.req” extension. The
default file name is “update.req”.
10. Close the DK2 Network Server, DK2 Network Server Remote Monitor, and
DESkey Configuration dialog boxes.
11. Send the generated CURF to your local Tektronix representative.
12. After Tektronix uses the CURF to generate the License Upgrade File (LUF)
and sends that file to you, perform the steps described in Floating License
Upgrade Procedure starting on page 6 to complete the upgrade.

User License Upgrade
MTS4EA License Upgrade Instructions 15
Troubleshooting the License Upgrade Process
Table 1 lists some common license upgrade problems and lists possible
solutions. If these solutions do not solve your upgrade problem, contact
Tektronix customer support.
Table 1: Troubleshooting upgrade problems
Upgrade problem Possible solution
The required license server machine is not listed on
Networking tab.
Add the server name using the Add button.
A license server machine is listed on Networking tab but is
not listed in DK2 Network Server Remote Monitor dialog.
Has the server that is entered in the client’s list of servers been
“applied”? Click Apply on the DESkey configuration dialog box and
refresh the DK2 Network Server Remote Monitor dialog box.
Is the Server service running on the server? If not, start the service.
Is the port number the same on both client and server, and is not
blocked by the network firewall? Select a suitable port number and
apply it to both client and server.
The new server port number is not being accepted by the
Networking tab.
Stop the Server service by clicking the Stop button. Change the port
number and click Apply. Start the Server service.
Clicking the “Get Request” button on the Licence Request
tab causes “Error 8000 calling server”.
Ensure that there is a dongle installed on the server machine.
Clicking the “Send Update” button on the Licence Request
tab causes “Error 4012 occurred sending update to server”.
Ensure that the upgrade file (LUF) is for the dongle installed on the
server machine.
Ensure that the upgrade file (LUF) has not already been applied to the
dongle. The LUF will work only for the first upgrade attempt.
gEnd of document g