Tektronix TMSSC2 User manual

Instruction Manual
TMSSC2
604-Pin Socket Hardware Support
071-1345-00
www.tektronix.com

Copyright ©Tektronix, Inc. All rights reserved.
Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication supercedes
that in all previously published material. Specifications and price change privileges reserved.
Tektronix, Inc., P.O. Box 500, Beaverton, OR 97077
TEKTRONIX and TEK are registered trademarks of Tektronix, Inc.

HARDWARE WARRANTY
Tektronix warrants that the products that it manufactures and sells will be free from defects in materials and
workmanship for a period of one (1) year from the date of shipment. If a product proves defective during this
warranty period, Tektronix, at its option, either will repair the defective product without charge for parts and labor,
or will provide a replacement in exchange for the defective product.
In order to obtain service under this warranty, Customer must notify Tektronix of the defect before the expiration
of the warranty period and make suitable arrangements for the performance of service. Customer shall be
responsible for packaging and shipping the defective product to the service center designated by Tektronix, with
shipping charges prepaid. Tektronix shall pay for the return of the product to Customer if the shipment is to a
location within the country in which the Tektronix service center is located. Customer shall be responsible for
paying all shipping charges, duties, taxes, and any other charges for products returned to any other locations.
This warranty shall not apply to any defect, failure or damage caused by improper use or improper or inadequate
maintenance and care. Tektronix shall not be obligated to furnish service under this warranty a) to repair damage
resulting from attempts by personnel other than Tektronix representatives to install, repair or service the product;
b) to repair damage resulting from improper use or connection to incompatible equipment; c) to repair any
damage or malfunction caused by the use of non-Tektronix supplies; or d) to service a product that has been
modified or integrated with other products when the effect of such modification or integration increases the time
or difficulty of servicing the product.
THIS WARRANTY IS GIVEN BY TEKTRONIX IN LIEU OF ANY OTHER WARRANTIES, EXPRESS
OR IMPLIED. TEKTRONIX AND ITS VENDORS DISCLAIM ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. TEKTRONIX’
RESPONSIBILITY TO REPAIR OR REPLACE DEFECTIVE PRODUCTS IS THE SOLE AND
EXCLUSIVE REMEDY PROVIDED TO THE CUSTOMER FOR BREACH OF THIS WARRANTY.
TEKTRONIX AND ITS VENDORS WILL NOT BE LIABLE FOR ANY INDIRECT, SPECIAL,
INCIDENTAL, OR CONSEQUENTIAL DAMAGES IRRESPECTIVE OF WHETHER TEKTRONIX OR
THE VENDOR HAS ADVANCE NOTICE OF THE POSSIBILITY OF SUCH DAMAGES.

SOFTWARE WARRANTY
Tektronix warrants that the media on which this software product is furnished and the encoding of the programs on
the media will be free from defects in materials and workmanship for a period of three (3) months from the date of
shipment. If a medium or encoding proves defective during the warranty period, Tektronix will provide a
replacement in exchange for the defective medium. Except as to the media on which this software product is
furnished, this software product is provided “as is” without warranty of any kind, either express or implied.
Tektronix does not warrant that the functions contained in this software product will meet Customer’s
requirements or that the operation of the programs will be uninterrupted or error-free.
In order to obtain service under this warranty, Customer must notify Tektronix of the defect before the expiration
of the warranty period. If Tektronix is unable to provide a replacement that is free from defects in materials and
workmanship within a reasonable time thereafter, Customer may terminate the license for this software product
and return this software product and any associated materials for credit or refund.
THIS WARRANTY IS GIVEN BY TEKTRONIX IN LIEU OF ANY OTHER WARRANTIES, EXPRESS
OR IMPLIED. TEKTRONIX AND ITS VENDORS DISCLAIM ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. TEKTRONIX’
RESPONSIBILITY TO REPLACE DEFECTIVE MEDIA OR REFUND CUSTOMER’SPAYMENTIS
THE SOLE AND EXCLUSIVE REMEDY PROVIDED TO THE CUSTOMER FOR BREACH OF THIS
WARRANTY. TEKTRONIX AND ITS VENDORS WILL NOT BE LIABLE FOR ANY INDIRECT,
SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES IRRESPECTIVE OF WHETHER
TEKTRONIX OR THE VENDOR HAS ADVANCE NOTICE OF THE POSSIBILITY OF SUCH
DAMAGES.

TMSSC2 604-Pin Socket Support
i
Table of Contents
General Safety Summary v...................................
Service Safety Summary vii....................................
Preface ix...................................................
Manual Conventions ix..............................................
Contacting Tektronix x..............................................
Getting Started
Product Description 1--1..............................................
Logic Analyzer Configuration 1--1......................................
P6860 Probes 1--2................................................
LAI Cables 1--2..................................................
Labeling P6860 Probes 1--3........................................
Labeling LAI Cables 1--3..........................................
Standard and Optional Accessories 1--3...................................
Probe Adapter Review 1--3............................................
Configure the Preprocessor Unit 1--4.....................................
Connecting the Logic Analyzer to a Target System 1--5......................
Tools 1--5......................................................
Connect the Logic Analyzer 1--5....................................
Removing the Microprocessor 1--10...................................
Removing the Probe Head from the Target System 1--10...................
Applying LAI Labels 1--11.............................................
Connect the Probes and LAI Cables 1--12..................................
LAI Cable and P6860 Probe Connections (Four Modules) 1--14.............
Fifth Module 1--14................................................
Applying and Removing Power 1--14.....................................
Logic Analyzer Software Compatibility 1--15...............................
Installing the Software 1--15............................................
Care and Maintenance 1--16.............................................
External Cleaning Only 1--16........................................
Short-Term Storage 1--17...........................................
Long-Term Storage 1--18...........................................
Shipping the Probe Adapter 1--19........................................
Specifications
Circuit Description 2--1...............................................
Loading Diagrams 2--3................................................
Specification Tables 2--5..............................................
Reference
Reference Tables 3--1..........................................
Viewing Reference Tables 3--1..........................................
To View a Symbol Table 3--1.......................................
To Extract Channel Assignments and Groups 3--1.......................

Table of Contents
ii
TMSSC2 604-Pin Socket Support
Replaceable Parts List
Parts Ordering Information 4--1.........................................
Using the Replaceable Parts List 4--2.....................................
Index

Table of Contents
TMSSC2 604-Pin Socket Support
iii
List of Figures
Figure 1--1: Master and Slave module configuration 1--2.............
Figure 1--2: Selecting your software on the preprocessor unit 1--4.....
Figure 1--3: Removing microprocessor probe head from the
target system 1--6..........................................
Figure 1--4: Attach the probe head to the target system 1--7..........
Figure 1--5: Attaching the heat sink brackets and microprocessor to the
target system 1--8..........................................
Figure 1--6: Attaching the heat sink to the target system 1--9..........
Figure 1--7: Remove the microprocessor with the extraction tool 1--10..
Figure 1--8: Apply LAI labels 1--11................................
Figure 1--9: LAI cable, P6860 probe, and preprocessor unit 1--12.......
Figure 1--10: LAI cable, P6860 probe, and module configurations 1--13..
Figure 1--11: Nonspecific probe head and case 1--17..................
Figure 1--12: Place preprocessor unit in the cardboard carton 1--18.....
Figure 1--13: Place cables in the cutouts 1--18.......................
Figure 1--14: Place accessories in the accessory tray 1--19.............
Figure 2--1: Probe adapter preliminary load model for typical signals 2--3
Figure 2--2: Pin header electrical load model for typical signals 2--4...
Figure 2--3: Socket electrical load model for typical signals 2--4.......
Figure 2--4: Mated Samtec model 2--4.............................
Figure 2--5: Receiver Model 2--4.................................
Figure 2--6: Dimensions of the probe head 2--8.....................
Figure 2--7: Dimensions of the preprocessor unit 2--9................
Figure 3--1: Channel Setup Export window 3--2....................
Figure 4--1: Probe adapter exploded view 4--5......................
Figure 4--2: Preprocessor unit exploded view 4--6...................
List of Tables
Table 1--1: Software selection 1--4................................
Table 1--2: P6860 probe and LAI cable configurations 1--13...........
Table 2--1: Electrical specifications for the target system 2--5........
Table 2--2: Electrical specifications for the AC input to the
preprocessor unit 2--6......................................
Table 2--3: BCLK timing and electrical specifications at 25 °C2--6...
Table 2--4: Environmental specifications 2--6......................
Table 2--5: Certifications and compliances 2--7.....................

Table of Contents
iv
TMSSC2 604-Pin Socket Support

TMSSC2 604-Pin Socket Support
v
General Safety Summary
Review the following safety precautions to avoid injury and prevent damage to
this product or any products connected to it. To avoid potential hazards, use this
product only as specified.
Only qualified personnel should perform service procedures.
While using this product, you may need to access other parts of the system. Read
the General Safety Summary in other system manuals for warnings and cautions
related to operating the system.
Use Proper Power Cord. Use only the power cord specified for this product and
certified for the country of use.
Connect and Disconnect Properly. Do not connect or disconnect probes or test
leads while they are connected to a voltage source.
Ground the Product. This product is grounded through the grounding conductor
of the power cord. To avoid electric shock, the grounding conductor must be
connected to earth ground. Before making connections to the input or output
terminals of the product, ensure that the product is properly grounded.
Observe All Terminal Ratings. To avoid fire or shock hazard, observe all ratings
and markings on the product. Consult the product manual for further ratings
information before making connections to the product.
Connect the ground lead of the probe to earth ground only.
Do Not Operate Without Covers. Do not operate this product with covers or panels
removed.
Use Proper Fuse. Use only the fuse type and rating specified for this product.
Avoid Exposed Circuitry. Do not touch exposed connections and components
when power is present.
Do Not Operate With Suspected Failures. If you suspect there is damage to this
product, have it inspected by qualified service personnel.
Do Not Operate in Wet/Damp Conditions.
Do Not Operate in an Explosive Atmosphere.
Keep Product Surfaces Clean and Dry.
Provide Proper Ventilation. Refer to the manual’s installation instructions for
details on installing the product so it has proper ventilation.
ToAvoidFireor
Personal Injury

General Safety Summary
vi
TMSSC2 604-Pin Socket Support
Terms in this Manual. These terms may appear in this manual:
WARNING. Warning statements identify conditions or practices that could result
in injury or loss of life.
CAUTION. Caution statements identify conditions or practices that could result in
damage to this product or other property.
Terms on the Product. These terms may appear on the product:
DANGER indicates an injury hazard immediately accessible as you read the
marking.
WARNING indicates an injury hazard not immediately accessible as you read the
marking.
CAUTION indicates a hazard to property including the product.
Symbols on the Product. The following symbols may appear on the product:
CAUTION
Refer to Manual
WARNING
High Voltage
Protective Ground
(Earth) Terminal
Symbols and Terms

TMSSC2 604-Pin Socket Support
vii
Service Safety Summary
Only qualified personnel should perform service procedures. Read this Service
Safety Summary and the General Safety Summary before performing any service
procedures.
Do Not Service Alone. Do not perform internal service or adjustments of this
product unless another person capable of rendering first aid and resuscitation is
present.
Disconnect Power. To avoid electric shock, switch off the instrument power, then
disconnect the power cord from the mains power.
Use Care When Servicing With Power On. Dangerous voltages or currents may
exist in this product. Disconnect power, remove battery (if applicable), and
disconnect test leads before removing protective panels, soldering, or replacing
components.
To avoid electric shock, do not touch exposed connections.

Service Safety Summary
viii
TMSSC2 604-Pin Socket Support

TMSSC2 604-Pin Socket Support
ix
Preface
This instruction manual contains specific information about the TMSSC2
604-Pin Socket support package and is part of a set of information on how to
operate this product on compatible Tektronix logic analyzers.
If you are familiar with operating microprocessor support packages on the logic
analyzer, you only need this instruction manual to set up and run the support
package.
If you are not familiar with operating microprocessor support packages, you need
to supplement this instruction manual with information on basic operations from
the Tektronix logic analyzer online help to set up and run the support package.
Manual Conventions
This manual uses the following conventions:
HA pound sign (#) following a signal name indicates an active low signal.
HThe phrase “information on basic operations” refers to basic information in
the logic analyzer online help.
HThe terms “Master” and “Slave” refer to modules that are located in
numbered slots (see Figure 1--1 on page 1--2).
HThe phrase “LAI cables” refers to the logic analyzer cables that connect the
preprocessor unit to the logic analyzer modules.

Preface
x
TMSSC2 604-Pin Socket Support
Contacting Tektronix
Phone [phone]*
Address Tektronix, Inc.
Department or name (if known)
14200 SW Karl Braun Drive
P.O. Box 500
Beaverton, OR 97077
USA
Web site www.tektronix.com
Sales support 1-800-833-9200, select option 1*
Service support 1-800-833-9200, select option 2*
Technical support Email: [email protected]
1-800-833-9200, select option 3*
6:00 a.m. -- 5:00 p.m. Pacific time
* This phone number is toll free in North America. After office hours, please leave a
voice mail message.
Outside North America, contact a Tektronix sales office or distributor; see the
Tektronix web site for a list of offices.

Getting Started

TMSSC2 604-Pin Socket Support
1-1
Getting Started
This section contains the following information about the TMSSC2 604-Pin
Socket support product:
HConfiguring the probe adapter, see page 1--4
HConnecting the logic analyzer to the target system, see page 1--5
HApplying power to the probe adapter, see page 1--14
HInstalling software, see page 1--15
HCaring for and maintaining the probe adapter, see page 1--16
Product Description
The probe adapter is an interposer design that allows the logic analyzer to
acquire data from a microprocessor in the operating environment with little effect
on the target system.
To accomplish this the probe adapter is connected to the target system, and then
the microprocessor is connected to the probe adapter. Signals from the micropro-
cessor based system flow through the probe adapter, the probe cables, and then to
the logic analyzer.
This software acquires signals for viewing including timing signals. Included
with the TMSSC2 604-Pin Socket probe adapter is the following software:
PUB32G10
PUB32G8N8
NOTE. The TMSSC2 probe adapter is compatible with the TMS117 and the
TMS122 software support packages. These software support packages are
available only to customers with a valid, restricted, secret nondisclosure
agreement (RS-NDA) with Intel.
Logic Analyzer Configuration
To use the probe adapter to acquire all signals except timing, you need a
Tektronix logic analyzer equipped with a minimum of four, 136-channel,
235 MHz merged modules. To also acquire timing signals, you need five,
136-channel, 235 MHz merged modules.

Getting Started
1-2
TMSSC2 604-Pin Socket Support
The modules must be configured and merged as shown in Figure 1--1. The
memory depth is chosen automatically based on the shallowest memory depth of
the four modules.
M
A
S
T
E
R
S
L
A
V
E
2
S
L
A
V
E
4
S
L
A
V
E
1
S
L
A
V
E
3
All signals
Plus timing
signals
Figure 1- 1: Master and Slave module configuration
The term Master module refers to the middle module of a 5-wide module merge.
The term Slave module refers to the modules to the left or right of the master
module of a 4 or 5-wide module merge. Figure 1--1 shows the configuration for a
4- or 5-wide module merge.
You can use the TLA7AXX, 235 MHz logic analyzer modules and P6860 probes
to connect to the TMSSC2 probe adapter.
For more information on connecting the P6860 Probes to the preprocessor unit,
seepage1--12.
Refer to the P6810, P6860, and P6880 Logic Analyzer Probes Instruction
manual, Tektronix part number 071-1059-XX, for more information. You can
access this manual from the Tektronix.com web site. You can also find informa-
tion about the P6860 probes in the logic analyzer online help.
You can use the TLA7AXX, 235 MHz logic analyzer modules and logic analyzer
interface (LAI) cables to connect to the TMSSC2 probe adapter. The LAI cables
(012-1661-XX) are specifically designed for use with the TMSSC2 probe
adapter.
For more information on connecting your LAI cables to the preprocessor unit,
seepage1--12.
P6860 Probes
LAI Cables

Getting Started
TMSSC2 604-Pin Socket Support
1-3
The probe adapter relies on the default channel mapping and labeling scheme for
the probes. Apply labels using the instructions described in the P6860 High
Density Logic Analyzer Probe Label Instructions, Tektronix part number
071-1123-XX.This manual can be accessed from the Tektronix.com web site.
This information is also located in the logic analyzer online help.
To apply labels to the LAI cables, see page 1--11.
Standard and Optional Accessories
A complete list of standard and optional accessories is provided in the Replace-
able Parts List on page 4--4.
Probe Adapter Review
Along with the TMSSC2 instruction manual, each logic analyzer includes
additional information that describes how to perform tasks common to support
products on that platform.
This additional information is located in the logic analyzer online help, an
installation manual, or a user manual. Review the additional information if you
are unfamiliar with using support products on a logic analyzer product.
Review electrical, environmental, and mechanical specifications in the Specifica-
tions section on page 2--1 as they pertain to the target system, as well as the
following information.
The TMSSC2 support product can acquire data from the microprocessor
operating at speeds of up to 200 MHz. The clock rate is not guaranteed for
prototype shipment of the product.
Contact your Tektronix sales representative for current information on the fastest
devices supported.
If data is acquired just before a power on Reset signal is observed by the target
system, the data acquired by the logic analyzer will be inaccurate.
The TMSSC2 probe adapter supports only a quad-pumped data bus.
The TMSSC2 probe adapter supports only a double-pumped address bus.
Labeling P6860 Probes
Labeling LAI Cables
System Clock Rate
Acquisition before Reset
Data Bus
Address Bus

Getting Started
1-4
TMSSC2 604-Pin Socket Support
The cache bus is not monitored; therefore, the cache must be disabled. Disabling
the cache makes all instruction prefetches visible on the bus so that they are
acquired and displayed and correctly disassembled.
Configure the Preprocessor Unit
You must configure the preprocessor unit for your software product before using
the probe adapter.
Software Support Selection. To select your software support, use Table 1--1 to
position the jumper on the preprocessor unit. Figure 1--2 shows the location of
the software support selector.
Table 1- 1: Software selection
Software support Pin
PUB32G8N8 or TMS117 1--2
PUB32G10 or TMS122 2--3
Software
support
selector
Figure 1- 2: Selecting your software on the preprocessor unit
Disabling the Cache