Tektronix WFM520UP User manual

WFM520UP and WVR520UP
WFM5200 Waveform Monitor and
WVR5200 Waveform Rasterizer
Upgrade Kit
ZZZ
Instructions
xx
Warning
The servicing instructions are for use by qualified personnel
only. To avoid personal injury, do not perform any servicing
unless you are qualified to do so. Refer to all safety summaries
prior to performing service.
www.tektronix.com
*P075102600*
075-1026-00

Copyright © Tektronix. All rights reserved. Licensed software products are owned by Tektronix or its subsidiaries
or suppliers, and are protected by national copyright laws and international treaty provisions.
Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication
supersedes that in all previously published material. Specifications and price change privileges reserved.
TEKTRONIX and TEK are registered trademarks of Tektronix, Inc.
Contacting Tektronix
Tektronix, Inc.
14150 SW Karl Braun Drive
P.O. Box 500
Beaverton, OR 97077
USA
For product information, sales, service, and technical support:
In North America, call 1-800-833-9200.
Worldwide, visit www.tektronix.com to find contacts in your area.

Table of Contents
General Safety Summary .......................................................................................... 1
Kit Description...................................................................................................... 3
Products......................................................................................................... 3
Installation Requirements..................................................................................... 4
Kit Parts Lists .................................................................................................. 4
Upgrade Installation................................................................................................ 5
Verify the Currently Installed Options....................................................................... 5
Install the Software Upgrade ................................................................................. 6
Install the Option Software Key............................................................................. 11
Verify the Upgrade............................................................................................ 12
WFM520UP and WVR520UP Upgrade Kit Instructions i

Table of Contents
ii WFM520UP and WVR520UP Upgrade Kit Instructions

General Safety Summary
Review the following safety precautions to avoid injury and prevent damage to
this product or any products connected to it.
To avoid potential hazards, use this product only as specified.
Only qualified personnel should perform service procedures.
While using this product, you may need to access other parts of a larger system.
Read the safety sections of the other component manuals for warnings and
cautions related to operating the system.
To Avoid Fire or Personal
Injury
Use ProperPowerCord. Use only the power cord specified for this product and
certified for the country of use.
Ground the Product. This product is grounded through the grounding conductor
of the power cord. To avoid electric shock, the grounding conductor must be
connected to earth ground. Before making connections to the input or output
terminals of the product, ensure that the product is properly grounded.
Observe All Terminal Ratings. To avoid fire or shock hazard, observe all ratings
and markings on the product. Consult the product manual for further ratings
information before making connections to the product.
Do not apply a potential to any terminal, including the common terminal, that
exceeds the maximum rating of that terminal.
Power Disconnect. The power cord disconnects the product from the power
source. Do not block the power cord; it must remain accessible to the user at
all times.
Do Not Operate Without Covers. Do not operate this product with covers or
panels removed.
Do Not Operate With Suspected Failures. If you suspect that there is damage to
this product, have it inspected by qualified service personnel.
Avoid Exposed Circuitry. Do not touch exposed connections and components
when power is present.
Use Proper AC Adapter. Use only the AC adapter specified for this product.
WFM520UP and WVR520UP Upgrade Kit Instructions 1

General Safety Summary
Do Not Operate in Wet/Damp Conditions.
Do Not Operate in an Explosive Atmosphere.
Keep Product Surfaces Clean and Dry.
Provide Proper Ventilation. Refer to the manual's installation instructions for
details on installing the product so it has proper ventilation.
TermsinthisManual These terms may appear in this manual:
WARNING. Warning statements identify conditions or practices that could result
in injury or loss of life.
CAUTION.Caution statements identify conditions or practices that could result in
damage to this product or other property.
Symbols and Terms on the
Product
These terms may appear on the product:
DANGER indicates an injury hazard immediately accessible as you read
the marking.
WARNING indicates an injury hazard not immediately accessible as you
read the marking.
CAUTION indicates a hazard to property including the product.
The following symbol(s) may appear on the product:
2 WFM520UP and WVR520UP Upgrade Kit Instructions

Kit Description
Kit Description
This document provides instructions for installing the following upgrades into
an existing Tektronix WFM5200 Waveform Monitor and WVR5200 Waveform
Rasterizer.
Table 1: Supported upgrades
Upgrade Description
Option 3G Adds support for 3G-SDI signal formats.
Option GEN Adds support for signal generation capability.
Option AUD Adds 16 channel Embedded AES/EBU Audio Monitoring.
Option DATA Adds Advanced Data Monitoring and Analysis Package.
Option CAM Adds Camera Monitoring package.
Option LOUD Adds Audio Loudness monitoring capabilities (requires that Option AUD is installed).
Option PROD Adds Advanced Gamut Monitoring Package (Spearhead Display and Luma Qualified Vector Display).
Products
All models of the following Tektronix instruments are supported by this kit:
WFM5200 Waveform Monitors
WVR5200 Waveform Rasterizers
WFM520UP and WVR520UP Upgrade Kit Instructions 3

Kit Description
Installation Requirements
The following are required to install the upgrade.
Table 2: Installation requirements
Item Description
Ethernet network connection Standard Ethernet network access
Standard PC Running Windows 98, Windows NT 4.0,
Windows ME, Windows 2000, Windows XP,
or Windows 7
SW Option Key An option key was included in this kit. This
key allows you to enable the option in your
instrument through the remote Web interface.
USB memory device (optional) This can be used if you want to download
the SW onto a memory device first, and then
download the SW to the instrument
WFM5200 or WVR5200 Specifications
and Performance Verification Technical
Reference and all test equipment listed within
to perform the verification checks (optional)
Tektronix part numbers 077-0533-XX and
077-0534-XX
Available for download from the Tektronix
Web site at www.tektronix.com/manuals
Kit Parts Lists
The following table lists the parts supplied with each upgrade kit. Before you
start the upgrade, verify that you received all of the parts for the upgrade kit you
ordered.
Table3: Kitpartslist
Quantity Part number Description
1EA —— ENVELOPE, IMPORTANT DOCUMENTS; CONTAINS
SOFTWARE OPTION KEY
1 EA 075-1026-XX INSTRUCTIONS; WFM520UP and WVR520UP
UPGRADES (this document)
1E
A—— OPTION KEY LABEL
1E
A——OPTION KEY CERTIFICATE (8.5 X 11, PRINTED)
4 WFM520UP and WVR520UP Upgrade Kit Instructions

Upgrade Installation
Upgrade Installation
This section provides instructions for the following:
Verifying the currently installed options
Installing the software upgrade
Installing the software option key
Verify the Currently Installed Options
The software option key supplied in this kit is based on the serial number you
supplied when you ordered the upgrade for the instrument. The new software
option key should enable the new option(s) you ordered, and also preserve your
previously purchased options.
Before you install the upgrade, perform the following steps to verify which
options are currently installed in your instrument. After you install the upgrade,
you will verify that the new options are installed and that any previously installed
options are still enabled.
1. Power on the instrument you are upgrading.
2. Press the CONFIG button on the front panel.
3. Navigate to Utilities >View Instrument Options.
4. Make a list of the installed options.
List installed options
WFM520UP and WVR520UP Upgrade Kit Instructions 5

Upgrade Installation
Install the Software Upgrade
CAUTION. To prevent upgrade failure, your instrument must have the latest
version of software installed before you install the hardware upgrade and before
you install the software option key.
Before You Begin You do not need to perform the software upgrade if your instrument has the latest
version of software installed. Perform the following steps to determine if the
software on your instrument needs to be upgraded:
1. Power on the instrument.
2. Verify the current software version installed on the instrument:
a. Press the CONFIG button on the front panel.
b. NavigatetoUtilities >View HW/SW Version.
c. In the Hardware and Software Versions display window, note the software
version number of the instrument.
Instrument Software version number
3. Verify the latest version of software at the Tektronix Web site:
a. Use the Web browser on a PC to navigate to the following Tektronix
Web site:
http://www.tektronix.com/downloads
b. On the Downloads Finder Web page, search by model number (such
as WFM5200) and filter by software and software type to locate the
software-upgrade package for the instrument.
c. Note the latest version number of the software-upgrade package(s).
Web site Software version number
4. If the latest software version at the Web site is newer than the version on your
instrument, you need to upgrade the software.
5. Download the latest version to your PC.
6. After the software package is downloaded, click on the self-extracting archive
to extract the following files into the directory of your choice: transfer.exe
and firmware.pkg. There may also be a readme.txt file.
6 WFM520UP and WVR520UP Upgrade Kit Instructions