Tektronix WFM6100 Opt. MB User manual

Service Manual
WFM6100, WFM7000, and WFM7100
Waveform Monitor
With Option FP
077-0090-00
Warning
The servicing instructions are for use by qualified
personnel only. To avoid personal injury, do not
perform any servicing unless you are qualified to
do so. Refer to all safety summaries prior to
performing service.
www.tektronix.com

Copyright ©Tektronix. All rights reserved. Licensed software products are owned by Tektronix or its subsidiaries or
suppliers, and are protected by national copyright laws and international treaty provisions.
Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication supercedes
that in all previously published material. Specifications and price change privileges reserved.
TEKTRONIX and TEK are registered trademarks of Tektronix, Inc.
Contacting Tektronix
Tektronix, Inc.
14200 SW Karl Braun Drive
P.O. Box 500
Beaverton, OR 97077
USA
For product information, sales, service, and technical support:
HIn North America, call 1-800-833-9200.
HWorldwide, visit www.tektronix.com to find contacts in your area.

Warranty 2
Tektronix warrants that this product will be free from defects in materials and workmanship for a period of one (1)
year from the date of shipment. If any such product proves defective during this warranty period, Tektronix, at its
option, either will repair the defective product without charge for parts and labor, or will provide a replacement in
exchange for the defective product. Parts, modules and replacement products used by Tektronix for warranty work
may be new or reconditioned to like new performance. All replaced parts, modules and products become the
property of Tektronix.
In order to obtain service under this warranty, Customer must notify Tektronix of the defect before the expiration
of the warranty period and make suitable arrangements for the performance of service. Customer shall be
responsible for packaging and shipping the defective product to the service center designated by Tektronix, with
shipping charges prepaid. Tektronix shall pay for the return of the product to Customer if the shipment is to a
location within the country in which the Tektronix service center is located. Customer shall be responsible for
paying all shipping charges, duties, taxes, and any other charges for products returned to any other locations.
This warranty shall not apply to any defect, failure or damage caused by improper use or improper or inadequate
maintenance and care. Tektronix shall not be obligated to furnish service under this warranty a) to repair damage
resulting from attempts by personnel other than Tektronix representatives to install, repair or service the product;
b) to repair damage resulting from improper use or connection to incompatible equipment; c) to repair any
damage or malfunction caused by the use of non-Tektronix supplies; or d) to service a product that has been
modified or integrated with other products when the effect of such modification or integration increases the time
or difficulty of servicing the product.
THIS WARRANTY IS GIVEN BY TEKTRONIX WITH RESPECT TO THE PRODUCT IN LIEU OF ANY
OTHER WARRANTIES, EXPRESS OR IMPLIED. TEKTRONIX AND ITS VENDORS DISCLAIM ANY
IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
TEKTRONIX’ RESPONSIBILITY TO REPAIR OR REPLACE DEFECTIVE PRODUCTS IS THE SOLE AND
EXCLUSIVE REMEDY PROVIDED TO THE CUSTOMER FOR BREACH OF THIS WARRANTY.
TEKTRONIX AND ITS VENDORS WILL NOT BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL,
OR CONSEQUENTIAL DAMAGES IRRESPECTIVE OF WHETHER TEKTRONIX OR THE VENDOR HAS
ADVANCE NOTICE OF THE POSSIBILITY OF SUCH DAMAGES.

WFM6100, WFM7000, and WFM7100 With Option FP Service Manual i
Table of Contents
General Safety Summary v...................................
Service Safety Summary vii....................................
Preface ix...................................................
Manual Conventions ix..............................................
Related Manuals ix.................................................
Introduction
Introduction 1--1..............................................
Service Strategy 1--1.................................................
Specifications 1--1...................................................
Performance Verification 1--1..........................................
Options and Accessories 1--1...........................................
Configurations 1--1..................................................
Hardware Installation 1--1.............................................
Product Upgrade 1--2.................................................
Operating Information 1--2............................................
Power-On Procedure 1--2..........................................
Power-Down Procedure 1--2........................................
Theory of Operation
Theory of Operation 2--1.......................................
Main Board 2--3.....................................................
Serial Digital Input Processing 2--3..................................
Reference Input 2--3..............................................
Digital Waveform Processing Engine 2--3.............................
Rasterizing Engine 2--3...........................................
Recursion and Picture Processing Engine 2--3..........................
Control Processor 2--4............................................
LTC 2 -- 4.......................................................
Front Panel 2--4.....................................................
Composite Input Option CPS 2--4.......................................
Audio Options: Options DS, AD, DD, and DDE 2--5........................
Audio Processing 2--5.............................................
Audio Inputs 2--5................................................
Audio Outputs 2--5...............................................
Option EYE/PHY 2--6................................................
Operation 2--7...................................................
Fan Control 2--7.....................................................
Power Supply and Distribution 2--7.....................................
Adjustment Procedures
Adjustments 3--1..............................................
Required Equipment 3--1..............................................
Procedures 3--1......................................................

Table of Contents
ii WFM6100, WFM7000, and WFM7100 With Option FP Service Manual
Maintenance
General Maintenance 4--1......................................
Preventing ESD 4--1.................................................
Inspection and Cleaning 4--2...........................................
General Care 4--2................................................
Interior Cleaning 4--2.............................................
Exterior Cleaning 4--2............................................
Troubleshooting 4--5.................................................
Getting Started 4--5...............................................
Detailed Troubleshooting Procedures 4--12................................
General Checks 4--12..............................................
Fan Failures 4--12.................................................
Primary Power Supply Tests 4--13....................................
Secondary Power Supply Tests 4--13..................................
Front Panel Button Troubleshooting 4--15..............................
LCD troubleshooting 4--15..........................................
Audio POST Failure 4--16..........................................
Examine Power On Self Tests (POST) results in the Diagnostic Log 4--18....
Run Advanced Diagnostics 4--18.....................................
Isolating Advanced Diagnostic Lissajous Errors 4--19....................
Option EYE/PHY Troubleshooting 4--20...............................
Removal and Replacement Procedures 4--25........................
Preparation 4--25.....................................................
Module Removal 4--27................................................
Top cover 4--27...................................................
Board supports 4--27...............................................
Rear panel 4--28..................................................
Composite board (Option CPS) 4--28..................................
Mezzanine board 4--28.............................................
EYE/PHY board (Option EYE/PHY) 4--29.............................
Audio boards (Options DS, AD, DD, and DDE) 4--29....................
Power Supply 4--30................................................
Fan assembly 4--30................................................
Front panel/LCD assembly 4--31.....................................
Repackaging Instructions 4--33...................................
Packaging 4--33......................................................
Shipping to the Service Center 4--33......................................
Replaceable Parts
Replaceable Parts 5--1..........................................
Parts Ordering Information 5--1.........................................
Module Servicing 5--1................................................
Using the Replaceable Parts Lists 5--2...................................
Abbreviations 5--2...................................................

Table of Contents
WFM6100, WFM7000, and WFM7100 With Option FP Service Manual iii
List of Tables
Table i: Related documentation ix..............................
Table 4--1: External inspection checklist 4--3......................
Table 4--2: Internal inspection checklist 4--4.......................
Table 4--3: Required test equipment 4--6..........................
Table 4--4: Symptoms and causes 4--7............................
Table 4--5: Main board secondary supplies 4--14....................
Table 4--6: Audio Main board secondary supplies 4--14..............
Table 4--7: Analog Audio secondary supplies 4--15...................
Table 4--8: Advanced diagnostic measurements 4--19.................
Table 4--9: Tools required for module removal 4--26.................
Table 4--10: Module removal 4--27................................

Table of Contents
iv WFM6100, WFM7000, and WFM7100 With Option FP Service Manual
List of Figures
Figure 2--1: Main block diagram 2--2.............................
Figure 2--2: Option EYE/PHY block diagram 2--8..................
Figure 4--1: Main board power supply test points and LEDs 4--22......
Figure 4--2: Audio main board power supply test point locations 4--23..
Figure 4--3: Analog Audio board power supply test point locations 4--24.
Figure 4--4: Module securing screws 4--28..........................
Figure 4--5: Front panel cable connections 4--31.....................
Figure 4--6: Front panel disassembly 4--32..........................
Figure 5--1: Circuit boards and connectors 5--5.....................
Figure 5--2: Chassis components 5--7.............................
Figure 5--3: Main board replaceable components 5--9...............
Figure 5--4: Analog audio breakout cable assembly 5--10..............

WFM6100, WFM7000, and WFM7100 With Option FP Service Manual v
General Safety Summary
Review the following safety precautions to avoid injury and prevent damage to
this product or any products connected to it.
To avoid potential hazards, use this product only as specified.
Only qualified personnel should perform service procedures.
While using this product, you may need to access other parts of the system. Read
the General Safety Summary in other system manuals for warnings and cautions
related to operating the system.
Use Proper Power Cord. Use only the power cord specified for this product and
certified for the country of use.
Connect and Disconnect Properly. Do not connect or disconnect probes or test
leads while they are connected to a voltage source.
Ground the Product. This product is grounded through the grounding conductor
of the power cord. To avoid electric shock, the grounding conductor must be
connected to earth ground. Before making connections to the input or output
terminals of the product, ensure that the product is properly grounded.
Observe All Terminal Ratings. To avoid fire or shock hazard, observe all ratings
and markings on the product. Consult the product manual for further ratings
information before making connections to the product.
Do not apply a potential to any terminal, including the common terminal, that
exceeds the maximum rating of that terminal.
Powering Off. The power cord provides Mains disconnect.
Replace Batteries Properly. Replace batteries only with the proper type and rating
specified.
Do Not Operate Without Covers. Do not operate this product with covers or panels
removed.
Use Proper Fuse. Use only the fuse type and rating specified for this product.
Avoid Exposed Circuitry. Do not touch exposed connections and components
when power is present.
Wear Eye Protection. Wear eye protection if exposure to high-intensity rays or
laser radiation exists.
Do Not Operate With Suspected Failures. If you suspect there is damage to this
product, have it inspected by qualified service personnel.
Do Not Operate in Wet/Damp Conditions.
ToAvoidFireor
Personal Injury

General Safety Summary
vi WFM6100, WFM7000, and WFM7100 With Option FP Service Manual
Do Not Operate in an Explosive Atmosphere.
Keep Product Surfaces Clean and Dry.
Provide Proper Ventilation. Refer to the manual’s installation instructions for
details on installing the product so it has proper ventilation.
Terms in this Manual. These terms may appear in this manual:
WARNING. Warning statements identify conditions or practices that could result
in injury or loss of life.
CAUTION. Caution statements identify conditions or practices that could result in
damage to this product or other property.
Terms on the Product. These terms may appear on the product:
DANGER indicates an injury hazard immediately accessible as you read the
marking.
WARNING indicates an injury hazard not immediately accessible as you read the
marking.
CAUTION indicates a hazard to property including the product.
Symbols on the Product. The following symbols may appear on the product:
CAUTION
Refer to Manual
WARNING
High Voltage
Protective Ground
(Earth) Terminal Standby
Symbols and Terms