Telguard TG-1 Express CDMA User manual

2
2
1
1
T
TG G- -1 1 E Ex xp pr re es ss s Q Qu ui ic ck k I In ns st ta al ll l G Gu ui id de e
Programming Codes
To Program the TG-1 Express:
1. After the TG-1 Express is initialized, connect a POTS phone to the RJ-45 jack
or lineman’s butt set to the tip and ring turrets.
2. Take the POTS phone off hook or put the butt set in talk mode. You should
hear dial tone.
3. Dial ###*, and you should hear one beep.
4. Dial #*, and you should hear one beep.
5. Dial the POTS command number 8XX; you should hear one beep.
6. Enter the command data; you should hear 2 beeps.
7. After the last POTS command, dial * and listen for 2 beeps. Then hang up to
terminate the POTS programming session.
Register for Telguard Service
There are four ways to register the Telguard unit:
1. register online at www.telguardonline.com,
2. send the electronic registration form at www.telular.com/telguard,
3. email the completed registration form to [e-mail], or
4. fax the completed registration form to 678-945-1651.
Connect Dialer and Power to the TG-1 Express
Connect the alarm panel’s dialer to the RJ-45 jack on the TG-1 Express.
If using the Single Line Interface Cable (SLIC) for power, connect the
RJ-45 cable’s orange wire to the alarm panel’s ground and its blue
wire to the panel’s auxiliary power,. If using the terminal block,
connect pins 4 and 5 to the panel’s ground and power.
Continued…
56042601
Mem
Loc. Field Setting (default indicated in bold)
851
STC Relay
Output
Reporting
Normally
Closed
Enter the SUM TOTAL of the events that you wish
to trip the STC relay by ADDING the
corresponding values:
00 = STC Relay Output Not Used
01 = LPF 08 = NSC
16 = RFC 32 = DTF
57 = ALL
852
STC Trip
Delay for
NSC
1=30 seconds, 2=60 seconds
3=3 minutes 4=10 minutes
5=20 minutes 6=30 minutes
7=45 minutes 8=60 minutes
9=24 hours
858 STC History
0 = terminate STC history display mode
1 = start STC history display mode
2 = clear STC history
868 PPF Delay
Timer
0 = disabled, 1 = 10 seconds, 2 = 20 seconds, …
15 = 150 seconds
873 Trip Input
Reporting
0 = no report
1 = report trip
874
Trip Input
Restoral
Reporting
0 = no report
1 = report restoral
875
Trip Input
Swinger
Function
0 = swinger function disabled
1 = swinger function enabled
899 Factory Default Unit

3
3
4
4
A
A
B
B
Connect the Antenna and Place the Unit
Connect the antenna to the antenna port, and press the RSSI button
on the side of the unit to put the LEDs into RSSI display mode. When
you have found a location that provides 2 ½ bars or more (LEDs 4 and
5 solid, and LED 3 flashing or solid), install the mounting screws and
attach the TG-1 Express to the mounting screws. Press the RSSI button
again to return the LEDs to normal display mode.
Activate the TG-1 Express
The last step is to trigger an alarm from the panel to activate the TG-1
Express. Note that the first alarm will activate the TG-1 Express with
the Telular Communication Center, and will not be sent to the central
station.
Optional Steps
Configure and Connect the Supervisory Trip Output
If required, configure the relay output using a butt set or phone set,
referencing the programming instructions on the back of this guide.
By default, the relay will trip for any system trouble condition detected
on the TG-1 Express. Connect the relay output (pins 1 and 2 on the
terminal block) to a 24 hour zone on the alarm panel.
Configure and Connect the Trip Input
The trip input may be configured to provide supervision independent
of the alarm panel, for applications such as external sensors and
tamper protection. Configure the trip and restoral reporting (they are
disabled by default) and the swinger setting using a butt set, and
connect the trip input and ground terminals to the external sensor.
LED Indicators (normal mode)
LED Symbol Color Showing Indication
LED #1
Activation Green
Solid On Unit is activated at the message
center and enabled
Off Unit not activated at the message
center
Flashing Unit is activated but disabled
LED #2
STC
(System Trouble
Condition)
Red
Off ALL OK
1 Flash STC – Low Power Failure
2, 3 Flashes N/A
4 Flashes STC – No Service Condition
5 Flashes STC – Radio Failure Condition
6 Flashes STC – Dial Tone Failure
7 Flashes STC – Panel Presence Failure
LED #3
MODE Yellow
Flashing Telguard TG-1 Express
communicating with alarm panel
Off Idle state
LED #4
Acknow-
ledgement
Red
Flashing
When flashing with LED #1 unit
has failed activation. CALL
TELGUARD TECHNICAL SUPPORT
Off TG-1 Express initialized
On TG-1 Express is waiting for response
from Telular Communication Center
LED #5
Radio Green
Short Flash (1
sec) Radio receiving message
Long Flash (2
sec) Radio sending message
LED #7
Trip Input Green
Solid On Trip input activated
Off Trip input not active or restored
LED #8
Power Red Solid On Power connected to unit