Teltonika FM1010 User manual

FM1010 User Manual
V1.2

2
Table of contents
1INTRODUCTION ..................................................................................................................... 6
1.1 ATTENTION............................................................................................................................ 6
1.2 INSTRUCTIONS OF SAFETY ......................................................................................................... 6
1.3 LEGAL NOTICE........................................................................................................................ 7
1.4 ABOUT DOCUMENT ................................................................................................................. 7
2BASIC DESCRIPTION ............................................................................................................... 7
2.1 PACKAGE CONTENTS ................................................................................................................ 7
2.2 BASIC CHARACTERISTICS ........................................................................................................... 8
2.3 TECHNICAL FEATURES............................................................................................................... 9
2.4 ELECTRICAL CHARACTERISTICS.................................................................................................. 11
2.5 ABSOLUTE MAXIMUM RATINGS............................................................................................... 11
3CONNECTION, PINOUT......................................................................................................... 12
3.1 HOW TO INSERT SIM CARD INTO FM1010 DEVICE: .................................................................... 12
3.2 INSTALLING FM1010 DRIVERS ................................................................................................ 13
3.3 NAVIGATE LED..................................................................................................................... 15
3.4 STATUS LED ........................................................................................................................ 15
3.5 OBD II ............................................................................................................................... 15
3.6 USB................................................................................................................................... 16
4FIRMWARE .......................................................................................................................... 17
4.1 UPDATING FIRMWARE USING USB CABLE .................................................................................. 17
5OPERATIONAL BASICS.......................................................................................................... 18
5.1 OPERATIONAL PRINCIPALS....................................................................................................... 18
5.2 SLEEP MODES....................................................................................................................... 18
 Sleep mode....................................................................................................................... 18
 Deep Sleep mode.............................................................................................................. 19
5.3 VIRTUAL ODOMETER.............................................................................................................. 20
5.4 FEATURES............................................................................................................................ 20
 Scenarios .......................................................................................................................... 20
 Trip ................................................................................................................................... 20
 Geofencing ....................................................................................................................... 21
5.5 CONFIGURATION.............................................................................................................. 21
INSTALLING FM1010 FOR CONFIGURATION:....................................................................................... 21
5.6 CONFIGURATOR.................................................................................................................... 22
5.7 RECORD STORAGE ................................................................................................................. 24
5.8 SYSTEM SETTINGS.................................................................................................................. 24
5.9 RECORDS SETTINGS................................................................................................................ 25
5.10 GSM SETTINGS,GPRS PART................................................................................................... 26
5.11 GSM SETTINGS,SMS PART .................................................................................................... 26
5.12 IGNITION SOURCE SETTINGS .................................................................................................... 27
5.13 DATA ACQUISITION MODE SETTINGS ........................................................................................ 27
5.14 FEATURES SETTINGS............................................................................................................... 31
 Scenarios settings ............................................................................................................ 31
 Trip settings...................................................................................................................... 32
 Geofencing settings.......................................................................................................... 33
 SMS events ....................................................................................................................... 35
5.14..1 SMS events configuration ................................................................................................... 37
5.15 I/O SETTINGS ....................................................................................................................... 40
 Event Generating ............................................................................................................. 42
 Hysteresis ......................................................................................................................... 43
6SMS COMMAND LIST ........................................................................................................... 43

3
6.1 SMS COMMAND LIST............................................................................................................. 43
 getstatus .......................................................................................................................... 44
 getweektime .................................................................................................................... 45
 getops .............................................................................................................................. 45
 getcfgtime........................................................................................................................ 45
 ggps.................................................................................................................................. 45
 getgps .............................................................................................................................. 45
 getinfo.............................................................................................................................. 46
 getver ............................................................................................................................... 46
 allver ................................................................................................................................ 47
 getio ................................................................................................................................. 47
 readio # ............................................................................................................................ 47
 getparam ####................................................................................................................. 47
 setparam #### ................................................................................................................. 47
 flush #,#,#,#,#,#,#............................................................................................................. 48
 banlist .............................................................................................................................. 48
 crashlog............................................................................................................................ 48
7DEBUG MODE ...................................................................................................................... 48
8PARAMETER LIST ................................................................................................................. 49
8.1 PARAMETERS VALUE TYPES...................................................................................................... 49
8.2 SYSTEM PARAMETERS ............................................................................................................ 49
 Sleep Mode (ID=1000)...................................................................................................... 49
 Sleep timeout (ID=1001) .................................................................................................. 50
 Mode Switch Source (ID=1002) ........................................................................................ 50
 Ignition Source (ID=1003)................................................................................................. 50
 Saving/Sending without time synchronization (ID=1005) ................................................ 50
 Power Voltage Low Level (ID=1006) ................................................................................ 50
 Power Voltage High Level (ID=1007)................................................................................ 50
8.3 RECORDS PARAMETERS .......................................................................................................... 51
 Sorting (ID=1010) ............................................................................................................. 51
 Active Data Link Timeout (ID=1011) ................................................................................ 51
 Server Response Timeout (ID=1012) ................................................................................ 51
8.4 GSM PARAMETERS ............................................................................................................... 52
 GPRS content activation (ID=1240).................................................................................. 52
 APN Name (ID=1242) ....................................................................................................... 52
 APN username (ID=1243)................................................................................................. 52
 APN Password (ID=1244) ................................................................................................. 52
 Domain (ID=1245) ............................................................................................................ 52
 Target Server Port (ID=1246) ........................................................................................... 53
 Protocol (ID=1247) ........................................................................................................... 53
 SMS Login (ID=1252) ........................................................................................................ 53
 SMS Password (ID=1253) ................................................................................................. 53
 SMS data sending settings (ID=1250) .............................................................................. 53
 Authorized phone numbers (ID=1260-1269).................................................................... 53
 SMS Event PreDefined Numbers (ID=150-159) ................................................................ 54
8.5 DATA ACQUISITION MODES PARAMETERS.................................................................................. 54
 Home Network GSM operator code “Vehicle on STOP” parameters ............................... 54
8.5..1 Min Period (ID=1540) ........................................................................................................... 54
8.5..2 Min Saved Records (ID=1543)............................................................................................... 54
8.5..3 Send Period (ID=1544).......................................................................................................... 54
8.5..4 GPRS Week Time (ID=1545).................................................................................................. 54
 Home Network GSM operator code “Vehicle MOVING” parameters .............................. 55
8.5..5 Min Period (ID=1550) ........................................................................................................... 55
8.5..6 Min Distance (ID=1551) ........................................................................................................ 55
8.5..7 Min Angle (ID=1552)............................................................................................................. 55

4
8.5..8 Min Saved Records (ID=1553)............................................................................................... 56
8.5..9 Send Period (ID=1554).......................................................................................................... 56
8.5..10 GPRS Week Time (ID=1555)................................................................................................ 56
 Roaming Network GSM operator code “Vehicle on STOP” parameters........................... 56
8.5..11 Min Period (ID=1560).......................................................................................................... 56
8.5..12 Min Saved Records (ID=1563)............................................................................................. 56
8.5..13 Send Period (ID=1564) ........................................................................................................ 56
8.5..14 GPRS Week Time (ID=1565)................................................................................................ 56
 Roaming Network GSM operator code “Vehicle MOVING” parameters.......................... 57
8.5..15 Min Period (ID=1570).......................................................................................................... 57
8.5..16 Min Distance (ID=1571) ...................................................................................................... 57
8.5..17 Min Angle (ID=1572)........................................................................................................... 57
8.5..18 Min Saved Records (ID=1573)............................................................................................. 57
8.5..19 Send Period (ID=1574) ........................................................................................................ 57
8.5..20 GPRS Week Time (ID=1575)................................................................................................ 58
 Unknown Network GSM operator code “Vehicle on STOP” parameters.......................... 58
8.5..21 Min Period (ID=1580).......................................................................................................... 58
8.5..22 Min Saved Records (ID=1583)............................................................................................. 58
8.5..23 Send Period (ID=1584) ........................................................................................................ 58
8.5..24 GPRS Week Time (ID=1585)................................................................................................ 58
 Unknown Network GSM operator code “Vehicle MOVING” parameters......................... 58
8.5..25 Min Period (ID=1590).......................................................................................................... 58
8.5..26 Min Distance (ID=1591) ...................................................................................................... 58
8.5..27 Min Angle (ID=1592)........................................................................................................... 59
8.5..28 Min Saved Records (ID=1593)............................................................................................. 59
8.5..29 Send Period (ID=1594) ........................................................................................................ 59
8.5..30 GPRS Week Time (ID=1595)................................................................................................ 59
8.6 FEATURES PARAMETERS ......................................................................................................... 59
 Scenarios Enable (ID=1600) ............................................................................................. 59
 Max Acceleration Force (ID=1602)................................................................................... 60
 Max Braking Force (ID=1603) .......................................................................................... 60
 Max Angular Velocity (ID=1604) ...................................................................................... 60
 Max allowed Speed (ID=1605) ......................................................................................... 60
 Trip (ID=1280) .................................................................................................................. 60
 Start Speed (ID=1281) ...................................................................................................... 60
 Ignition Off Timeout (ID=1282) ........................................................................................ 61
 Trip Continuous distance counting (ID=1283) .................................................................. 61
 Geofencing ....................................................................................................................... 61
8.6..1 Frame border (ID=1020) ....................................................................................................... 61
8.6..2 Geofence Zone #1 Shape (ID=1030) ..................................................................................... 61
8.6..3 Geofence Zone #1 Priority (ID=1031) ................................................................................... 61
8.6..4 Geofence Zone #1 Generate Event (ID=1032) ...................................................................... 62
8.6..5 Geofence Zone #1 Longitude (X1) (ID=1033)........................................................................ 62
8.6..6 Geofence Zone #1 Latitude (Y1) (ID=1034)........................................................................... 62
8.6..7 Geofence Zone #1 Longitude (X2) (ID=1035)........................................................................ 62
8.6..8 Geofence Zone #1 Latitude (Y2) (ID=1036)........................................................................... 63
 AutoGeofencing ............................................................................................................... 63
8.6..9 Enable/Disable (ID=1101) ..................................................................................................... 63
8.6..10 Activation Timeout (ID=1102)............................................................................................. 63
8.6..11 AutoGeofence event Priority (ID=1103) ............................................................................. 63
8.6..12 AutoGeofence event generating (ID=1104)........................................................................ 63
8.6..13 Radius (ID=1105)................................................................................................................. 64
8.7 ACCELEROMETER PARAMETERS ................................................................................................ 64
8.7..1 Acceleration range configuration (ID=1290)......................................................................... 64
8.7..2 Acceleration threshold configuration (ID=1291) .................................................................. 64
8.7..3 Acceleration duration (ID=1292) .......................................................................................... 64
8.7..4 Movement filter start (ID=1293)........................................................................................... 64
8.7..5 Movement filer stop (ID=1294) ............................................................................................ 64
8.8 I/O PARAMETERS.................................................................................................................. 65
 I/O#1 property parameter (ID=1300)............................................................................... 65
 I/O#1 priority (ID=1301)................................................................................................... 65

5
 I/O#1 High level (ID=1302)............................................................................................... 65
 I/O#1 Low level (ID=1303)................................................................................................ 65
 I/O#1 logic operand (ID=1304)......................................................................................... 66
 I/O#1 averaging length (ID=1305) ................................................................................... 66
8.9 SMS EVENT CONFIGURATION .................................................................................................. 67
 I/O#1 element SMS event configuration (ID=100) ........................................................... 67
9MODULE INSTALLATION ...................................................................................................... 69
9.1 INSTALLING FM1010 MODULE: .............................................................................................. 69
1) LOCATE OBD-II CONNECTOR IN YOUR CAR (SEE CAR OWNER’S MANUAL FOR THE LOCATION OF THE
CONNECTOR) 69
2) PLUG IN FM1010 DEVICE IN OBD-II CONNECTOR. ..................................................................... 69
3) IF STATUS AND NAVIGATE LED LIGHTS TURN ON,DEVICE IS READY TO USE.......................................... 69
9.2 INSTALLATION RECOMMENDATIONS:......................................................................................... 69
10 CHANGE LOG ....................................................................................................................... 70

6
1INTRODUCTION
1.1 Attention
Do not disassemble the device. If the device is
damaged, before unplugging the power supply, do not
touch the device.
All wireless data transferring devices produce
interference that may affect other devices which are
placed nearby.
Please consult representatives of your vehicle model
regarding OBD II location on your vehicle. In case you
are not sure of proper connection, please consult
qualified personnel.
The programming must be performed using a second
class PC (with autonomic power supply).
The device is susceptible to water and humidity.
Any installation and/or handling during a lightning
storm are prohibited.
FM1010 has USB interface;
Please use cables provided with FM1010 device.
Teltonika is not responsible for any harm caused by
using wrong cables for PC <-> FM1010 connection.
Warning! Do not use FM1010 device if it distracts driver
or causes inconvenience due to OBD II placement.
Device must not interfere with driver.
1.2 Instructions of safety
This chapter contains information on how to operate FM1010 safely. By following these
requirements and recommendations, you will avoid dangerous situations. You must read these
instructions carefully and follow them strictly before operating the device!
The device uses a 10 V...16 V DC power supply. The nominal voltage is 12 V DC. The
allowed range of voltage is 10 V...16 V DC.
To avoid mechanical damage, it is advised to transport the FM1010 device in an impact-
proof package.
Before dismounting the device from the vehicle, ignition must be off.

7
1.3 Legal Notice
Copyright © 2014 Teltonika. All rights reserved. Reproduction, transfer, distribution or
storage of part or all of the contents in this document in any form without the prior written
permission of Teltonika is prohibited.
Other products and company names mentioned here may be trademarks or trade names
of their respective owners.
The manufacturer reserves the right to make changes and/or improvements at any time in
design, functionality, parameters and electrical characteristics without any prior notice and
without incurring obligations.
1.4 About document
This document contains information about the architecture, possibilities, mechanical
characteristics, and configuration of the FM1010 device.
Acronyms and terms used in document
PC –Personal Computer.
GPRS –General Packet Radio Service
GPS –Global Positioning System
GNSS –Global Navigation Satellite System
GSM –Global System for Mobile Communications
SMS –Short Message Service
AC/DC –Alternating Current/Direct Current
I/O –Input/Output
Record –AVL data stored in FM1010 memory. AVL data contains GNSS and I/O information
AVL packet - data packet that is being sent to server during data transmission. AVL packet
contains from 1 to 50 records.
2BASIC DESCRIPTION
FM1010 is a terminal with GNSS and GSM connectivity, which is able to determine the
object’s coordinates and transfer them via the GSM network. This device is perfectly suitable for
applications, which need location acquirement of remote objects. FM1010 has a USB port for
device status log output and entering configurations.
Note: Monitorable basic vehicle parameters depend on vehicle mark and
model.
2.1 Package contents
1
The FM1010 device is supplied to the customer in a cardboard box containing all the
equipment that is necessary for operation. The package contains:
FM1010 device;
OBD II power supply adapter (accessory is optional);
USB cable.
170mAh Li-ion battery (optional)
1
Package content depends on Order Code, and can be customized by customer needs.

8
2.2 Basic characteristics
GSM / GPRS features:
Teltonika TM11Q quad band module (GSM 850 / 900 / 1800 / 1900 MHz);
GPRS class 10;
SMS (text, data).
GNSS features:
TG3300 32 channel (or equivalent) receiver;
Up to -161 dBm sensitivity.
Hardware features:
Cortex®-M3 processor;
1 MB internal Flash memory
Built-in accelerometer.
Interface features:
Power supply: 10 ÷ 16V;
USB port;
Ignition input
LEDs indicating device status.
Note: Ignition input parameter depends on vehicle mark and model.
Special features:
Any element event triggers (speed, temperature, etc.);
Highly configurable data acquisition and sending;
Multiple Geo-fence areas;
Sleep mode;
Deep sleep mode;
Configurable scenarios available;
Authorized number list for remote access;
Firmware update over GPRS or USB port;
Configuration update over GPRS, SMS or USB port;
TCP/IP or UDP/IP protocol support;
Up to 8000 records storing.

9
2.3 Technical features
Part name
Physical specification
Technical details
Navigation LED
LED
Power supply 10...16 V DC
2W Max
Energy consumption1:
GPRS: average 85 mA r.m.s,
Nominal: average 48 mA r.m.s,
GNSS Sleep: average 21 mA,
Battery charge current:
average 100 mA,
Deep Sleep: average less than 2 mA2
Operation temperature:
-25⁰C ... +55⁰C
Storage temperature:
-40⁰C ... +70⁰C
Storage relative humidity 5 ... 95 % (no
condensation)
Modem LED
LED
GNSS
Internal GNSS antenna
GSM
Internal GSM antenna
OBD-II
connector
Standard OBD-II connector
USB
Mini USB socket
Table 1. FM1010 specifications
1 Energy consumption has been tested at 12V voltage.
2
When in Deep Sleep mode no data storing and sending is activated.

10
Figure 1 FM1010 view & dimensions (tolerance ±1mm)

11
2.4 Electrical characteristics
VALUE
CHARACTERISTIC DESCRIPTION
Min.
Typ.
Max.
Unit
Supply Voltage:
Supply Voltage (Recommended Operating Conditions)
10
16
V
Digital Output (Open Drain grade):
Drain current (Digital Output OFF)
120
uA
Drain current (Digital Output ON,
Recommended Operating Conditions)
300
mA
Static Drain-Source resistance (Digital
Output ON)
300
mOhm
Digital Input:
Input resistance (Ignition)
15
kOhm
Input Voltage (Recommended Operating
Conditions)
0
Supply
voltage
V
Input Voltage threshold (Ignition)
5
V
2.5 Absolute Maximum Ratings
VALUE
CHARACTERISTIC DESCRIPTION
Min.
Typ.
Max.
Unit
Supply Voltage (Absolute Maximum Ratings)
-16
16
V
Digital Input (Ignition) Voltage (Absolute Maximum
Ratings)
-32
32
V

12
3CONNECTION, PINOUT
3.1 How to insert SIM card into FM1010 device:

Gently open FM1010 case using screwdrivers

Remove FM1010 case

Insert SIM card as shown

13

Insert battery wire to connector*

Attach top housing cover

Device is ready
________________________________________

*Battery is optional
3.2 Installing FM1010 drivers
Software requirements:
•Operating system 32-bit and 64-bit: Windows XP with SP3 or later, Windows Vista,
Windows 7.
• MS .NET Framework V3.5 or later (http://www.microsoft.com or
http://avl1.teltonika.lt/downloads/tavl/Framework/dotnetfx35setupSP1.zip).
Drivers:
Please download Virtual COM Port drivers from Teltonika website:
http://avl1.teltonika.lt/downloads/FM1010 /vcpdriver_v1.3.1_setup.zip

14
Installing drivers:
Extract and run VCPDriver_V1.3.1_Setup.exe. This driver is used to detect FM1010 device
connected to the computer. Click 'Next' in driver installation window (figures below):
Figure 2 Driver installation window
This will launch device driver installation wizard. In the following window click ‘Next’
button again:
Figure 3 Driver installation window
Setup will continue installing drivers and will display a window about successful process at
the end. Click 'Finish' to complete setup:
Figure 4 Driver installation window
You have now installed drivers for FM1010 device successfully.

15
3.3 Navigate LED
Behaviour
Meaning
Permanently switched on
GNSS signal is not received
Blinking every second
Normal mode, GNSS is working
Off
GNSS is turned off because:
Deep sleep mode
Or
GNSS antenna short circuited
3.4 Status LED
Behaviour
Meaning
Blinking every second
Normal mode
Blinking every 2 seconds
Deep sleep mode
Blinking fast for a short time
Modem activity
Blinking fast constantly
Boot mode
Off
Device is not working
Or
Device firmware being flashed
3.5 OBD II
Pin
Nr.
Pin Name
Description
1
Ignition input
2
-
3
-
4
GND (-)
Ground pin.
5
GND (-)
Ground pin.
6
-
Figure 5 OBD II pinout

16
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
Power +(1016) V DC
Power range +(10...16) V DC to ground
3.6 USB
Mini USB connector
Figure 6 Mini USB type B connector
FM1010 connected to PC creates an STM Virtual COM Port, which can be used as a system
port (to flash firmware and configure the device):
Figure 7 COM-Ports
Table 2. OBD II pinout description

17
4FIRMWARE
4.1 Updating firmware using USB cable
FM1010 functionality is always improving, new firmware versions are developed. Current
module firmware version can be retrieved from Configurator. See configuration description for
details.
Contact sales manager to get the latest firmware.
Device must be powered on. Connect FM1010 to PC with the USB cable. Launch “Firmware
Updater”, select COM port to which device is connected, click connect, and when IMEI and
Firmware version fields are filled, start the update. Device needs some time to send IMEI and
Firmware version, so do not be afraid if IMEI will not show up immediately, disconnect and after
1-2 minutes try to connect again. Update process may take up to several minutes.
Figure 8 FM1010 firmware updater screen
To avoid possible battery malfunctions starting from firmware version 00.03.22 internal
battery completely disconnects from when temperature reaches approx. 60 C degrees.
We strongly recommended to keep firmware version up to date (00.03.22 or newer).

18
Figure 9 FM1010 firmware updating finished
When you see a table like in Figure 9, it means that the firmware is flashed to FM1010
successfully. You may now close the update window and start using your FM1010 device.
5OPERATIONAL BASICS
5.1 Operational principals
FM1010 module is designed to acquire records and send them to the server. Records
contain GNSS data and I/O information. Module uses GNSS receiver to acquire GNSS data and is
powered with three data acquire methods: time-based, distance-based and angle-based method.
Note, that if FM1010 loses connection to GNSS satellites, it continues to make records, however
coordinate in these records remains the same (last known coordinate). Method’s details are
described in section 5.13. All data is stored in flash memory and later can be sent via GPRS.
GPRS and SMS settings are described in later sections. FM1010 communicates with server
using special data protocol. Data protocol is described in “FMXXXX Protocols” document.
FM1010 can be managed by SMS commands. SMS Command list is described in SMS
COMMAND LIST section. Module configuration can be performed over TCP or via SMS.
Configuration parameters and modes are described in “FMXXXX Protocols” document.
5.2 Sleep modes
Sleep mode
FM1010 is able to go to Sleep mode after configurable Sleep timeout. This timeout
(defined period) starts counting when device is in STOP mode. After timeout is reached and all
conditions for sleep mode are met, device goes to sleep mode. While in sleep mode, FM1010
turns GNSS module off and it is not making new periodic records. Only event records is being
recorded with last known coordinate and sent to AVL server. As a result power usage decreases
allowing saving vehicle battery.
FM1010 can enter sleep mode if ALL of these conditions are met:

19
FM1010 has to be configured to work in Sleep mode;
Device must be synchronized time with GNSS satellites;
FM1010 has to be in „X on Stop Mode“ (Configured by Mode switch parameter);
Ignition (Configured to be detected by Power Voltage, Ignition or Accelerometer) is
off;
Sleep timeout is reached.
FM1010 exits sleep mode when if ONE of following conditions are true:
FM1010 switches to “X on Moving Mode”;
Ignition (Configured to be detected by Power Voltage, Ignition or Accelerometer) is
turned on.
Deep Sleep mode
While in deep sleep mode, FM1010 sets GNSS receiver to sleep mode and turns off
GSM/GPRS module (it is not possible to wake up device via SMS). Despite records with last
known coordinate are being saved and send to AVL server (GSM/GPRS module is turned on to
send data and after that it is turned off again), power usage is decreased to save vehicle’s
battery. Note, that power saving depends on two configurable parameters: send period and min.
record saving period in “X on Stop Mode”.
FM1010 can enter deep sleep mode if ALL of these conditions are met:
FM1010 has to be configured to work in Deep Sleep mode;
Device must be synchronized time with GNSS satellites;
FM1010 has to be in „X on Stop Mode“ (Configured by Mode switch parameter);
Movement by accelerometer is not detected;
Ignition (Configured to be detected by Power Voltage, Ignition or Accelerometer) is
off;
Min. Record Saving Period (Data Acquisition Mode settings) must be bigger than
Active Data Link Timeout parameter, that FM1010 could close GPRS link.
Send period (Data Acquisition Mode settings) minus Active Data Link Timeout must
be more than 90 sec., that FM1010 could close GPRS link for at least 90 sec.
USB cable is not connected.
Sleep timeout is reached.
FM1010 exits deep sleep mode when if ONE of following conditions are true:
Movement by accelerometer is detected;
Ignition (Configured to be detected by Power Voltage, Ignition or Accelerometer) is
turned on.
USB cable is connected;
Note: In order to save GPRS traffic records saved in deep sleep mode do not
contain below listed I/O elements information:
PDOP, HDOP, Odometer, Speedometer , Cell ID, Area Code, GNSS power

20
5.3 Virtual odometer
Virtual odometer is used to calculate traveled distance in FM1010 as a separate I/O
element. When FM1010 detects movement, it starts counting distance using GNSS signal: every
second it checks current location and calculates distance between current and previous point. It
keeps adding these intervals until it is time to make a record, then FM1010 records its location
and adds odometer value, which is equal to the sum of all distances, measured every second.
When record is made, odometer resets to zero and distance calculation starts all over again.
Virtual odometer as an I/O element can be also used with Trip feature, read chapters and
for more details.
5.4 Features
Using available features can greatly increase FM1010 usability options.
Scenarios
Two scenarios are available on FM1010 device.
Green Driving or/and Over Speeding;
Green Driving Scenario. Helps to prevent and inspect driver about harsh driving. Scenario
continuously monitors: accelerating force, braking force and cornering angles.
To save GPRS traffic Green Driving event will be generated (included into sent records)
only when FM1010 measured values are higher than those set in configuration, without
additional I/O settings.
To prevent generating false events, harsh acceleration and harsh braking is monitored only
when following conditions are fulfilled:
Ignition (Configured to be detected by Power Voltage, Ignition or Accelerometer) is
turned on.
Vehicle speed is equal or higher than 10km/h.
Harsh cornering is monitored only when following conditions are fulfilled:
Ignition (Configured to be detected by Power Voltage, Ignition or Accelerometer) is
turned on.
Vehicle speed is equal or higher than 30km/h.
Note: Green Driving Scenario is a factor on various cars and various drivers
testing phase and can be subject to changes. Teltonika is constantly working
on improvement of the functionality of the devices, and strongly recommends
using the latest version of the firmware.
Over Speeding Scenario. Helps to prevent from exceeding fixed speed and inspects driver if
needed.
Trip
Trip customizable feature enables user extended monitoring of performed trips (from
engine start at present location to engine stop at arrived location), log their start and stop points,