Teltonika FMB910 Installation guide

Quick Manual
v1.1
Track & trace device
FMB910

2
FMB910 | Wiki
Table of Contents
Know your device............................................................................... 3
Pinout................................................................................................. 4
Wiring scheme................................................................................... 5
Set up your device ............................................................................. 6
How to insert SIM card and connect the battery........................... 6
PC Connection (Windows)................................................................ 7
How to install USB drivers (Windows)............................................. 7
Configuration (Windows) ................................................................. 7
Quick SMS configuration.................................................................. 9
Mounting recommendations .......................................................... 10
LED indications................................................................................. 11
Characteristics.................................................................................. 11
Basic characteristics ....................................................................... 11
Electrical characteristics................................................................. 12
Safety information ........................................................................... 14
Certification and Approvals ............................................................. 15
Warranty........................................................................................... 16
Warranty Disclaimer........................................................................16

3
FMB910 | Wiki
Know your device
Figure 1 FMB910 device view

4
FMB910 | Wiki
Pinout
Table 1 FMB910 pinout
PIN NUMBER
PIN NAME
DESCRIPTION
1
VCC (6-30) V DC (+)
Power supply (6-30) V DC (+)
2
GND (-)
Ground pin
3
DIN 1
Digital input, channel 1. DEDICATED
FOR IGNITION INPUT
4
AIN 1
Analog input, channel 1. Input range: 0-
30 V DC
5
DOUT 1
Digital output, channel 1. Open
collector output. Max. 0,5 A DC
Figure 2 FMB910 pinout

5
FMB910 | Wiki
Figure 3 FMB910 Wiring scheme
Wiring scheme
1Automotive relay
^1

6
FMB910 | Wiki
Set up your device
How to insert Micro SIM card and
connect the battery
1. Gently remove FMB910 cover using plastic pry
tool from both sides.
2. Separate PCB from plastic cover and connect power
supply cable.
3. Insert Micro-SIM card as shown with PIN request
disabled or read Security info how to enter it later in
Configurator. Make sure that Micro-SIM card cut-off
corner is pointing forward to slot.
4. Connect internal back-up battery.
5. Attach device cover back. (Do not forget to configure
the device before reassembling the device!)
6. Device ready to use!
Figure 4 Cover removal
Figure 5 Wiring harness connection
Figure 6 Micro SIM card insert
Figure 7 Battery connection
Figure 8 Attaching cover back
Figure 9 Device ready to use

7
FMB910 | Wiki
PC Connection (Windows)
1. Power-up FMB910 with DC voltage 6-30 V power supply using
power cable. LED’s should start blinking, see “LED indications”.
2. Connect device to computer using Micro-USB cable or
Bluetooth connection:
•Using Micro-USB cable
▬You will need to install USB drivers, see "How to install
USB drivers (Windows)"
•Using Bluetooth
▬FMB910 Bluetooth is enabled by default. Turn on
Bluetooth on your PC, then select Add Bluetooth or other
device > Bluetooth. Choose your device named –
“FMB910_last_7_imei_digits”, without LE in the end. Enter
default password 5555, press Connect and then select
Done.
3. You are now ready to use the device on your computer.
How to install USB drivers
(Windows)
1. Please download COM port drivers from here.
2. Extract and run TeltonikaCOMDriver.exe.
3. Click Next in driver installation window.
4. In the following window click Install button.
5. Setup will continue installing the driver and eventually the
confirmation window will appear. Click Finish to complete the
setup.
Configuration (Windows)
At first FMB910 device will have default factory settings set. These
settings should be changed according to the user's needs. Main
configuration can be performed via Teltonika Configurator
software. Get the latest FMB910 Configurator version from here.
Configurator operates on Microsoft Windows OS and uses
prerequisite MS .NET Framework. Make sure you have the correct
version installed.
Table 2 MS .NET requirements
MS .NET REQUIREMENTS
Windows Vista
Windows 7
Windows 8.1
Windows 10
MS .NET Framework
4.6.2
32 and 64 bit
www.microsoft.com
Downloaded Configurator will be in compressed archive. Extract it
and launch Configurator.exe. After launch software language can
be changed by clicking in the right bottom corner (Figure 10
Language selection).

8
FMB910 | Wiki
Configuration process begins by pressing on connected device
(Figure 11 Device connected via USB).
After connection to Configurator Status window will be displayed
(Figure 12 Configurator Status window).
Various Status window tabs display information about GNSS,GSM,
I/O, Maintenance and etc. FMB910 has one user editable profile,
which can be loaded and saved to the device. After any
modification of configuration the changes need to be saved to
device using Save to device button. Main buttons offer following
functionality:
1. Load from device –loads configuration from device.
2. Save to device –saves configuration to device.
3. Load from file –loads configuration from file.
4. Save to file –saves configuration to file.
5. Update firmware –updates firmware on device.
6. Read records –reads records from the device.
7. Reboot device –restarts device.
8. Reset configuration –sets device configuration to
default.
Most important configurator section is GPRS –where all your
server and GPRS settings can be configured and Data Acquisition –
where data acquiring parameters can be configured.
More details about FMB910 configuration using Configurator can
be found in our Wiki.
Figure 11 Device connected via USB
Figure 10 Language selection
Figure 12 Configurator Status window

9
FMB910 | Wiki
Quick SMS configuration
Default configuration has optimal parameters present to ensure
best performance of track quality and data usage.
Quickly set up your device by sending this SMS command to it:
Note: Before SMS text, two space symbols should be inserted.
GPRS settings:
•
2001
–APN
•
2002
–APN username (if there
are no APN username, empty
field should be left)
•
2003
–APN password (if there
are no APN password, empty
field should be left)
Server settings:
•
2004
–Domain
•
2005
–Port
•
2006
–Data sending protocol
(0 –TCP, 1 –UDP)
Default configuration settings
Movement and ignition detection:
Vehicle movement will
be detected by
accelerometer
Ignition will be detected
by vehicle power voltage
between 13,2 –30 V
Device makes a record On Moving if one of these events happen:
300 seconds passes
Vehicle turns 10 degrees
Vehicle drives 100
meters
Speed difference
between last coordinate
and current position is
greater than 10 km/h
Device makes a record On Stop if:
1 hour passes while
vehicle is stationary
and ignition is off
Records sending to server:
If device has made a
record it is sent to the
server every 120
seconds
After successful SMS configuration, FMB910 device will synchronize
time and update records to configured server. Time intervals and
default I/O elements can be changed by using Teltonika
Configurator or SMS parameters
" setparam
2001
:APN;
2002
:APN_username;
2003
:APN_password;
2004
:Domain;
2005
:Port;
2006
:0;"

10
FMB910 | Wiki
Mounting recommendations
•Connecting wires
▬Wires should be fastened to the other wires or non-moving
parts. Try to avoid heat emitting and moving objects near
the wires.
▬The connections should not be seen very clearly. If factory
isolation was removed while connecting wires, it should be
applied again.
▬If the wires are placed in the exterior or in places where they
can be damaged or exposed to heat, humidity, dirt, etc.,
additional isolation should be applied.
▬Wires cannot be connected to the board computers or
control units.
•Connecting power source
▬Be sure that after the car computer falls asleep, power is still
available on chosen wire. Depending on car, this may
happen in 5 to 30 minutes period.
▬When the module is connected, measure the voltage again
to make sure it did not decrease.
▬It is recommended to connect to the main power cable in
the fuse box.
▬3 A, 125 V external fuse shall be used.
•Connecting ignition wire
▬Be sure to check if it is a real ignition wire i.e. power does
not disappear after starting the engine.
▬Check if this is not an ACC wire (when key is in the first
position, most of the vehicle electronics are available).
▬Check if power is still available when you turn off any of
vehicles devices.
▬Ignition is connected to the ignition relay output. As
alternative, any other relay, which has power output when
ignition is on, may be chosen.
•Connecting ground wire
▬Ground wire is connected to the vehicle frame or metal
parts that are fixed to the frame.
▬If the wire is fixed with the bolt, the loop must be connected
to the end of the wire.
▬For better contact scrub paint from the spot where loop is
going to be connected.