Teltonika FMP100 Installation guide

Quick Manual
V1.4
Plug and Play tracker
FMP100

2
FMP100 | Wiki
Table of Contents
Table of Contents .......................................................................... 2
Know your device .......................................................................... 3
Know your device .......................................................................... 4
Set up your device......................................................................... 5
How to insert Nano-SIM card .......................................................... 5
PC Connection (Windows)................................................................ 6
Configuration (Windows) ................................................................. 6
Quick SMS configuration.................................................................. 8
User Interface................................................................................ 9
Keyboard ........................................................................................ 9
Basic characteristics ..................................................................... 9
Safety information...................................................................... 12
Certification and Approvals ....................................................... 13
Warranty ...................................................................................... 14
Warranty Disclaimer ....................................................................... 14

3
FMP100 | Wiki
Know your device
Figure 1 FMP100 device view (With covers)
Business/Private
or Panic Button

4
FMP100 | Wiki
Know your device

5
FMP100 | Wiki
Set up your device
How to insert Nano-SIM card
1. Insert the SIM tray removal tool into the hole on the SIM card
tray and then push until the tray pops out.
2. Insert Nano-SIM card as shown with PIN request disabled or
read our Wiki how to enter it later in Teltonika Configurator.
Make sure that Nano-SIM card is fitted properly into the tray.
3. Insert the SIM card tray back.
4. After configuration, see “PC Connection (Windows)”.
Device is ready to be mounted.
Figure 4 SIM tray insert
Figure 3 Nano-SIM card insert
Figure 2 SIM tray removal
2
2
3
Figure 3 SIM tray removal

6
FMP100 | Wiki
PC Connection (Windows)
•Connection by using Bluetooth:
1) Power-up FMP100 with DC voltage (12 –30 V) power
supply. LED’s should start blinking, see “Error! Reference s
ource not found.”.
2) FMP100 Bluetooth is enabled by default. Turn on
Bluetooth on your PC, then select Add Bluetooth or
other device > Bluetooth. Choose your device named –
“FMBxxx_last_7_imei_digits”, without LE in the end.
Enter default password 5555, press Connect and then
select Done.
•If Bluetooth connection is not possible, please refer to the
FMP100 Wiki page on how to open the device casing and
connect it via Micro-USB.
Configuration (Windows)
At first FMP100 device will have default factory settings set. These
settings should be changed according to the user's needs. Main
configuration can be performed via Teltonika Configurator
software. Get the latest Configurator version from here.
Configurator operates on Microsoft Windows OS and uses
prerequisite MS .NET Framework. Make sure you have the correct
version installed.
Table 1 MS .NET requirements
MS.NETrequirements
Operating
system
MS .NET Framework
version
Version
Links
Windows Vista
Windows 7
Windows 8.1
Windows 10
MS .NET Framework
4.6.2
32 and 64 bit
www.microsoft.com
Downloaded Configurator will be in compressed archive. Extract it
and launch Configurator.exe. After launch software language can
be changed by clicking in the right bottom corner (Figure 5
Language selection).

7
FMP100 | Wiki
Configuration process begins by pressing on connected device
(Figure 6 Device connected via Bluetooth).
After connection to Configurator Status window will be displayed
(Figure 7 Configurator Status window).
Various Status window tabs display information about GNSS,
GSM, I/O, Maintenance and etc. FMP100 has one user editable
modification of configuration the changes need to be saved to
device using Save to device button. Main buttons offer following
functionality:
1. Load from device –loads configuration from device.
2. Save to device –saves configuration to device.
3. Load from file –loads configuration from file.
4. Save to file –saves configuration to file.
5. Update firmware –updates firmware on device.
6. Read records –reads records from the device.
7. Reboot device –restarts device.
8. Reset configuration –sets device configuration to
default.
Most important configurator section is GPRS –where all your
server and GPRS settings can be configured and Data Acquisition
–where data acquiring parameters can be configured.
More details about FMP100 configuration using Configurator can
be found in our Wiki.
Figure 5 Language selection
Figure 6 Device connected via Bluetooth
Figure 7 Configurator Status window

8
FMP100 | Wiki
Quick SMS configuration
Default configuration has optimal parameters present to ensure
best performance of track quality and data usage.
Quickly set up your device by sending this SMS command to it:
Note: Before SMS text, two space symbols should be inserted.
GPRS settings:
•
2001
–APN
•
2002
–APN username (if there
are no APN username, empty
field should be left)
•
2003
–APN password (if there
are no APN password, empty
field should be left)
Server settings:
•
2004
–Domain
•
2005
–Port
•
2006
–Data sending protocol
(0 –TCP, 1 –UDP)
Default configuration settings
Movement and ignition detection:
Vehicle movement will
be detected by
accelerometer
Ignition will be detected
by vehicle power voltage
between 13,2 –30 V
Device makes a record On Moving if one of these events happen:
300 seconds passes
Vehicle turns 10 degrees
Vehicle drives 100
meters
Speed difference
between last coordinate
and current position is
greater than 10 km/h
Device makes a record On Stop if:
1 hour passes while
vehicle is stationary
and ignition is off
Records sending to server:
If device has made a
record it is sent to the
server every 120
seconds
After successful SMS configuration, FMP100 device will
synchronize time and update records to configured server.
Time intervals and default I/O elements can be changed by
using Teltonika Configurator or SMS parameters.
" setparam
2001
:APN;
2002
:APN_username;
2003
:APN_password;
2004
:Domain;
2005
:Port;
2006
:0"

9
FMP100 | Wiki
User Interface
Table 3 User interface LED indication scenarios
SCENARIO
Indication
Meaning
GSM error
Red LED 500 ms
blink 3 times +
Buzzer
SIM is not inserted, device
can’t connect to the
operator or GSM signal is
being jammed
No GNSS fix
Red LED 1000 ms
blink 1 time
Device doesn’t have valid
GNSS fix and is searching
for coordinates
GNSS fix
Green LED 1000 ms
blink 1 time
Device has valid GNSS fix
Key pressed
1000 ms interval
Buzzer while active
Key is pressed and held
Private Trip
Green LED 500 ms
blink 3 times +
Buzzer
Battery is almost fully
discharged
Business Trip
Blue LED 500 ms
blink 3 times +
Buzzer
Indication used to remind
the user that device is still
operational
Note! This table contains only the default scenarios. Additional
scenarios/default ones can be modified using Teltonika
Configurator. User is able to select different indication color (Red,
Green or Blue), frequency of LED blinking and buzzer status.
Keyboard
Table 4 Keyboard default actions
Action
Function
1 Click
Check Trip Mode
2 Clicks
Change Trip Mode
Long Click
Alarm
Basic characteristics
Table 5 Basic characteristics
Module
Name
Teltonika TM2500
Technology
GSM/GPRS/GNSS/BLUETOOTH
GNSS
GNSS
GPS, GLONASS, GALILEO, BEIDOU,
SBAS, QZSS, DGPS, AGPS
Receiver
33 channel
Tracking sensitivity
-165 dBM
Position accuracy
< 2.5 CEP
Velocity accuracy
< 0,1 m/s (within +/- 15% error)
Hot start
< 1 s
Warm start
< 25 s
Cold start
< 35 s

10
FMP100 | Wiki
Cellular
Technology
GSM
2G bands
Quad-band 850 / 900 / 1800 / 1900
MHz
Data transfer
GPRS Multi-Slot Class 12 (up to 240
kbps)
Data support
SMS (text/data)
Power
Input voltage range
10 - 30 V DC with overvoltage
protection
Back-up battery
3.7 V 170 mAh (0.63 Wh)
Power consumption
At 12V < 5 mA (Ultra Deep Sleep)
At 12V < 7 mA (Deep Sleep)
At 12V < 7 mA (Online Deep Sleep)
At 12V < 8 mA (GPS Sleep)
At 12V < 28 mA (nominal)
Bluetooth
Specification
4.0 + LE
Supported peripherals
Temperature and Humidity sensor,
Hands-free headset, Inateck Barcode
Scanner, Universal BLE sensor
support
Interface
Connection
Cigarette lighter socket
Configurable buttons
1
GNSS antenna
Internal High Gain
GSM antenna
Internal GSM High Gain
USB
1 x USB 2.0 Micro-USB for
configuration
1 x USB type A for external device
charging (5V 1A)
LED indication
RGB LED
SIM
Nano-SIM
Memory
128MB internal flash memory
Physicalspecification
Dimensions
96,7 x 33,4 x 27,5 mm (L x W x H)
Operatingenvironment
Operating temperature (without
battery)
-40 °C to +85 °C
Storage temperature (without battery)
-40 °C to +85 °C
Operating humidity
5% to 95% non-condensing
Ingress Protection Rating
IP41
Battery charge temperature
0 °C to +45 °C
Battery discharge temperature
-20 °C to +60 °C
Battery storage temperature
-20 °C to +45 °C for 1 month
-20 °C to +35 °C for 6 months
Features
Sensors
Accelerometer
Scenarios
Green Driving, Over Speeding
detection, Jamming detection, GNSS
Fuel Counter, Excessive Idling
detection, Unplug detection, Towing
detection, Crash detection, Auto
Geofence, Manual Geofence, Trip
Sleep modes
GPS Sleep, Online Deep Sleep, Deep
Sleep, Ultra Deep Sleep