Tenda IT Series User manual

4MP Bullet Security Camera
IT Series
Quick Installation Guide
* Please read this guide before you start with the quick setup for this camera upon the first use.
For product or function details, please go to www.tendacn.com to download the user guide.
IT7-LRS-4 is used for illustrations here unless otherwise specified. The actual product prevails.

Waterproof kit×1
Screw hole for ceiling installation
Power jack
Use the power adapter to power on the camera.
Power-related parameters can be found on the
label attached to the device.
Ethernet port,10/100 Mbps auto-negotiation
− If the camera supports the IEEE 802.3af standard,
this port can be connected to the PoE port of a
PoE power sourcing equipment for power supply.
− If the camera does not support standard PoE, this
port can be connected to routers, switches,etc.
Camera ×1
- 1 -
Appearance
Package contents
Quick installation guide×1
Screw hole for wall installation
Microphone
4MP Bullet Security Camera
IT Series
Pleaseread this guide beforeyou start with the quick setup for this camera upon the first use.
Forproduct or function details,please go to www.tendacn.com to download theuser guide.
IT7-LRS-4is used forillustrations here unless otherwise speci fied.The actual produc t prevails.
Quick Installation Guide

- 2 -
Install the device
Install the camera
The bracket installation process may vary based on different
manufacturers and models. The following figures are for reference only.
Please refer to the actual bracket.
Wall installation
❶
❷
− Please make sure the wall or the ceiling is strong enough to withstand three times the weight
of the camera.
− You may need to prepare a hammer drill, a drill bit, a rubber hammer, a screwdriver, and a
ladder for the installation.
− The camera supports ceiling and wall installation. The installation bracket required for the
installation is not included in the package. Please purchase it by yourself.
Tips

- 3 -
Screws provided with the bracket
Reserve the screws for later use（step❺）
❸
❹
❺

- 4 -
❻
❼
Install the camera (Running the cable through
the wall is taken as an example)
Adjust the monitoring direction and fix
the camera
Screw Anchor
Horizontal adjustment
Vertical adjustment
Vertically adjust the screw
Horizontally adjust the screw

- 5 -
The bracket installation process may vary based on different
manufacturers and models. The following figures are for reference only.
Please refer to the actual bracket.
Ceiling installation
❶
❷
Installation template

- 6 -
Fix the camera
❸
❹
Screw
Anchor
Knob

- 7 -
Adjust the monitoring direction
❺
Horizontal adjustment
Vertical adjustment
Orientation knob

- 8 -
Install the waterproof kit
You can install the waterproof kit and wrap the end with waterproof tape
for the Ethernet port and power jack as required.When you connect the
Ethernet cable to the Ethernet port of the camera,the waterproof kit
installation steps are as follows.
The included waterproof kit is not applicable to the Ethernet cable with the protection
cover on the connector. Ethernet cable with protection over is shown below.
Note
❶ ❷
❸
❺
❹

- 9 -
The series of cameras needs to be used with the NVR.You should add
cameras on the NVR's Web UI. For detailed steps,please refer to the user
manual of the corresponding NVR.
The series of cameras includes ordinary cameras and PoE cameras.Please
connect the cable according to the actual conditions.
Manage the device through Network Video
Recorder(NVR)
Ordinary camera topology
− The camera supports DC power supply (power-related parameters can be found on the label
attached to the device). The power adapter is not included in the package, so you need to
purchase a power adapter that meets the requirements (port specification: 5.5*2.1 mm).
− The PoE camera supports the IEEE 802.3af standard.
Tips
POWER LAN VGA USB
1 2 3 4 5
Router
WAN LAN LAN
Uplink port
Switch NVR
Monitor
Internet
Camera Camera Camera
Power outlet