Tenergy E6AC User manual

Getting Started .....................................................
Specifications ......................................................
Special Features..................................................
Controls and Connections ..................................
Determining Battery Type and Specifications ....
2
2
Input Power .......................................................... 2
4
3
3
Please read the manual completely before use!
Starting Charge ........................................................
Charge Complete .....................................................
5
6
Care and Handling of NiMH Batteries .....................
Care and Handling of LiPo and LiFe Batteries .......
7
7
Error Messages and Troubleshooting Guide ......... 6

* Build-in AC power supply is great for portability
* A DC power lead with alligator clips easily connects to many 12V DC power sources
* Easy to read LED shows battery voltage, charge current and capacity
* Push button controls and audible tones make for easy set up and control
* Reverse polarity protection and over-current protection ensure operation safety
AC Input: For indoor use, the charger includes a built-in switching AC power supply that
delivers power by connecting the AC power cord to a common 100-240AC outlet.
DC Input: This charger can be powered by a portable 12V DC power source. On the left side
of the charger, connect the DC power cord’s alligator clips directly to the output terminal.
Always match the poliarties (Red lead to red “ + ” terminal, Black lead to black “ - ” terminal).
To utilize the charger’s absolute maximum power capabilities, the DC power source must be
capable of delivering at least 5 amps while maintaining 12V DC.
WARNING! Never accidentally touch positive (+) and negative (-) input
connection together when connected to 12V DC power as it might result in
permanent damage to power source and charger.
Always connect the charger first, then connect the battery to charge lead.
100-240V AC 50/60Hz
11-18V DC, built in lead with alligator clips
Reverse polarity and current overload protection
134x110x60mm
269g
1-6S LiPo/LiFe
1-15S NiMH
0.1-5A
50W max.
Peak detection for NiMH, CC/CV for Lithiums
360 minutes(Defualt)
5mV
±5mV per cell
INPUT POWER

DEC
CELL
INC
I.R.
START
V/A/mAh
11-18V DC Input
TYPE
STOP
LED Screen TYPE/STOP Button: For selecting LiPo, LiFe
and NiMH battery and to manually stop charging
DEC/CELL: For viewing battery’s voltage on
LED or to decrease charge current
INC/I.R.: To view battery’s cell I.R. on LED or to
increase charge current
START/V/A/mAh: To view battery’s charging
voltage/current/capacity
Always connect the charger first. Then connect the battery to the charge lead. Always match polarities on the
battery wires, charge leads and banana connector black connections to black(-), red connections to red (+).
BALANCE PORTS: To connect a balancing connector of lithium battery pack

IN
I.R.
LP 5.0 LP
LF 5.0
5.0
capacity:50%
WARNING! Never set the battery type to a type that does not match
your battery as it might result in fire!

4.20 C2 4.20 C3
4.20 C6 4.20 C5
4.20 C4
I. .
>2S AUTO RETURN
voltage
(V)
current
(A)
25.0
capacity
(mAh)
{
DURING CHARGE
To view charging status
To view individual cell impedance
To view individual cell voltage

E6
FU The battery is full.
18E1
LED ERROR MESSAGE AND SOLUTION
E2 Connection disruption. Make sure a good connection exists between the battery and charger.
E3 Reverse polarity. Re-connect the battery to charger’s output with the proper polarity
E4 The battery has been disconnected during charge. Re-establish a good physical connection between the battery
and charger, and re-start charge.
E5 Internal electronic interruption or malfunction has occurred. Restart the charger. If error message still shows up,
please contact the manufacturer for further troubleshoot.
E7 Li-xx voltage detection error. The pack voltage cannot be read properly
E8 Balance voltage error. Re-connect the balancing cable.
SP 180-minute safety timer by default. You can restart the charge or disconnect the battery from the charger
LP-FU
LED

need to be cool down immediately.
WARNING!! DO NOT try to charge lithium-polymer(LiPo) or LiFe cells in the same way as other
battery types! Always read the instructions that are included with your lithium batteries carefully
before use. Failure to follow these care and handling instructions can quickly result in severe,
permanent damage to the batteries and their surroundings and even start a FIRE!