Tennant 1100 Product manual

Portable Carpet Extractor
1100
Model No.:
607721
607729 – Pac
Operator and Parts Manual
607722
Rev. 00 (11-99)
FAX: [phone]
CUSTOMER SERVICE: 1–800-982-7658
TENNANT COMPANY
Commercial Products
12875 RANSOM STREET
HOLLAND MI 49424 U.S.A.

OPERATION
2Tennant 1100 (07–99)
This manual is furnished with each new model. It
provides necessary operation and maintenance
instructions and an illustrated parts list.
Read this manual completely and understand the
machine before operating or servicing it.
Use the illustrated Parts Lists to order parts. Before
ordering parts or supplies, be sure to have your
machine model number and serial number handy.
Parts and supplies may be ordered by phone or mail
from any authorized parts and service center,
distributor or from any of the manufacturer’s
subsidiaries.
This machine will provide excellent service. However,
the best results will be obtained at minimum costs if:
The machine is operated with reasonable care.
The machine is maintained regularly - per the
machine care instructions provided.
The machine is maintained with manufacturer
supplied or equivalent parts.
MACHINE DATA
Pleasefill out at time of installation for future reference.
Model No.-
Install. Date -
Serial No.-
1999 Tennant Company Printed in U.S.A.
TABLE OF CONTENTS
SAFETY PRECAUTIONS 3. . . . . . . . . . . . . . . . . . . . . . .
MACHINE COMPONENTS 4. . . . . . . . . . . . . . . . . . . . . .
MACHINE SETUP 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MACHINE OPERATION 5. . . . . . . . . . . . . . . . . . . . . . . . .
DRAINING RECOVERY TANK 6. . . . . . . . . . . . . . . . . . .
MAINTENANCE 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
STORING MACHINE 7. . . . . . . . . . . . . . . . . . . . . . . . . . .
TROUBLE SHOOTING 8. . . . . . . . . . . . . . . . . . . . . . . . .
SPECIFICATIONS 9. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PARTS LIST 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ELECTRICAL DIAGRAM 16. . . . . . . . . . . . . . . . . . . . . .
OPTIONAL PARTS 17. . . . . . . . . . . . . . . . . . . . . . . . . . .

OPERATION
Tennant 1100 (11–99) 3
SAFETY PRECAUTIONS
This machine is suited to clean carpet and upholstery
in an indoor environment and is not constructed for
any other use. Use only recommended accessory
tools and cleaning solutions.
All operators must read, understand and exercise the
following Important Safety Instructions.
The following safety alert symbols are used throughout
this manual as indicated in their description.
WARNING: To warn of hazards or unsafe
practices which could result in severe personal
injury or death.
FOR SAFETY: To identify actions which must be
followed for safe operation of equipment.
The following information signals potentially dangerous
conditions to the operator or equipment:
FOR SAFETY:
1. Do not operate machine:
– Unless trained and authorized.
– Unless operator manual is read and
understood.
– In flammable or explosive areas unless
designed for use in those areas.
– With damaged cord or plug.
– If not in proper operating condition.
– In outdoor areas.
– In standing water.
– With the use of additional extension cords.
Only use manufacturer ’s extension cord
supplied with machine which has proper
capacity and is grounded.
2. Before operating machine:
– Make sure all safety devices are in place
and operate properly.
3. When using machine:
– Do not run machine over cord.
– Do not pull machine by plug or cord.
– Do not pull cord around sharp edges or
corners.
– Do not unplug by pulling on cord.
– Do not stretch cord.
– Do not handle plug with wet hands.
– Keep cord away from heated surfaces.
– Report machine damage or faulty
operation immediately.
– Follow mixing and handling instructions
on chemical containers.
4. Before leaving or servicing machine:
– Turn off machine.
– Unplug cord from wall outlet.
5. When servicing machine:
– Unplug cord from wall outlet.
– Avoid moving parts. Do not wear loose
jackets, shirts, or sleeves.
– Use manufacturer supplied or approved
replacement parts.
WARNING: Hazardous Voltage. Shock or
electrocution can result. Always unplug machine
before servicing.
WARNING: Flammable materials can cause
an explosion or fire. Do not use flammable
materials in tank(s).
WARNING: Flammable materials or reactive
metals can cause an explosion or fire. Do not pick
up.
GROUNDING INSTRUCTIONS
Machine must be grounded. If it should
malfunction or breakdown, grounding provides a
path of least resistance for electrical current to
reduce the risk of electrical shock. This machine
is equipped with a cord having an
equipment–grounding conductor and grounding
plug. The plug must be plugged into an
appropriate outlet that is properly installed in
accordance with all local codes and ordinances.
Do not remove ground pin; if missing, replace
plug before use.
GROUNDED OUTLET
(3 HOLE)
GROUNDING PIN

OPERATION
4Tennant 1100 (07–99)
MACHINE COMPONENTS
34
1
5
13
6
2
12 11
9
7
10
8
1. ON/OFF Switch 7. Solution Tank Lid
2. Drain Hose 8. Lockable Casters
3. Solution Hose 9. Lift Handle/Hose
Connector Guide
4. Recovery Dome/ 10. Floor Tool
Vacuum Hose
Connection 11. 4.6m (15 ft) Solution Hose
5. Power Cord 12. 4.6m (15 ft) Vacuum Hose
6. Cord Store Hook 13. Optional 127mm (5 in)
Hand Tool
MACHINE SETUP
PRE–OPERATION
1. Vacuum the floor to remove particles and other
debris.
2. Inspect power cord for damage.
FILL SOLUTION BLADDER
1. Unscrew and remove flat clear lid. Fill solution
bladder with 38 liters (10 gal) of hot water, 60°C
(140°F) maximum (Figure 1).
FIG. 1.
2. Add recommended cleaning agent to proper
dilution ratio.
FOR SAFETY: When using machine, follow mixing
and handling instructions on chemical containers.
WARNING: Flammable materials can cause
an explosion or fire. Do not use flammable
materials in tank(s).
3. After filling solution bladder, replace lid and tighten
securely.
NOTE: Suction in recovery tank will overexpand
solution bladder if lid is not secure.
ATTENTION: If using powered chemicals, do not
mix chemicals in solution bladder. Mix powdered
chemicals thoroughly in a bucket before pouring
into machine. Powders are unlikely to dissolve
completely and can clog solution pump system.
ATTENTION: Use separate buckets to fill and
empty extractor. Use a clean bucket to fill
machine, and empty dirty water into a separate
bucket. Dirty water in solution bladder will clog
solution pump system.
4. Connect vacuum hose to recovery dome and
solution hose to quick coupler located in front of
handle (Figure 2).
FIG. 2.
5. Route hoses through front lift handle (Figure 3).

OPERATION
Tennant 1100 (11–99) 5
FIG. 3.
NOTE: Routing hoses through handle will allow easy
machine mobility while operating cleaning tool.
6. Attach recommended cleaning tool to opposite
end of hoses.
7. If desired, lock front casters to keep machine from
moving.
8. Plug extension power cord into machine and then
plug into a grounded wall outlet (Figure 4).
GROUNDED
3 HOLE OUTLET
GROUND PIN
FIG. 4.
FOR SAFETY: Do not operate machine with the
use of additional extension cords. Only use
manufacturer’s extension cord supplied with
machine which has proper capacity and is
grounded.
MACHINE OPERATION
FOR SAFETY: Do not operate machine unless
operator manual is read and understood.
FLOOR TOOL OPERATION
1. Activate ON/OFF switch to ”ON”.
2. Place floor tool so bottom of stainless steel shoes
are parallel to floor. Squeeze trigger and apply
downward pressure on floor tool head and slowly
pull tool backwards using both hands. Release
trigger 150 mm (6 in) from end of stroke
(Figure 5).
FIG. 5.
3. Push floor tool forward over same path with trigger
released when returning for next stroke. Continue
this pull and push method with a slight overlap of
each stroke.
NOTE: For heavily soiled areas, repeat stroke or
change angle of stroke.
WARNING: Flammable materials or reactive
metals can cause an explosion or fire. Do not pick
up.
ATTENTION: Do not allow water or foam to enter
float shut–off screen in recovery tank. Screen will
not stop foam intake and vacuum motor damage
will result (not covered by warranty) . If foam
develops, remove dome and pour 29.6 ml (1 oz) of
anti–foam solution into recovery tank.
HAND TOOL OPERATION
NOTE: This machine cleans most synthetic
upholstery very well. Fabrics like Herculon and
synthetic velvets will clean with excellent results.
Extraction in not recommended for most cottons, silks,
wools or natural fiber velvets. Check cleaning
instructions sewn in furniture by manufacturer for
further instructions. Extra caution should be taken with
furniture that has been reupholstered. Any material
under new upholstery may bleed and discolor new
fabric.
1. Vacuum upholstery before cleaning.
2. Test fabric for colorfastness: Pour a small amount
of cleaning solution on a white cloth and hold
damp portion of cloth against an area of
upholstery which is hidden from view. Hold cloth in
place for one minute. If color does not transfer to
cloth it should be safe to clean. However, always
use your best judgement.
3. Activate ON/OFF switch to ”ON”.

OPERATION
6Tennant 1100 (11–99)
4. Place hand tool on furniture and squeeze trigger
while applying a downward pressure on hand tool
head and slowly pull tool backwards. Release
trigger just shy from end of stroke (Figure 6).
FIG. 6.
NOTE: Be careful not to over wet upholstery. Overlap
strokes to avoid streaking. Repeat stroke using only
vacuum to get fabric as dry as possible.
WARNING: Flammable materials or reactive
metals can cause an explosion or fire. Do not pick
up.
ATTENTION: Do not allow water or foam to enter
float shut–off screen in recovery tank.
AFTER CLEANING
1. When finished cleaning, turn off switch, unplug
power cord and drain and rinse out recovery tank.
2. Disconnect solution and vacuum hoses and
extension cords from machine. Neatly coil hoses
and cord after each use.
ATTENTION: Relieve water pressure from tool
before disconnecting hose. Squeeze trigger for
five seconds after turning off switches.
DRAINING RECOVERY TANK
NOTE: When solution bladder becomes empty while
cleaning, recovery tank must be emptied.
1. Turn switch off and disconnect power cord.
FOR SAFETY: When servicing machine, unplug
cord from wall outlet.
2. Remove drain hose from holder, position a
discharge bucket under drain hose and twist off
drain hose knob (Figure 7).
FIG. 7.
NOTE: Do not use same bucket for filling clean water
bladder!
3. Replace drain hose knob tightly before cleaning
again.
4. After final draining, remove recovery dome and
rinse both tank and dome thoroughly to prevent
odor buildup.
MAINTENANCE
To keep machine in good working condition, simply
follow machines daily, weekly and monthly
maintenance procedures.
WARNING: Hazardous Voltage. Shock or
electrocution can result. Always unplug machine
before servicing.
INTERNAL COMPONENTS SERVICE
For internal component service, machine is designed
to hinge open. Make sure the tanks are empty before
opening. Follow instructions below:
1. Remove two hex–head bolts at front lift handle,
using a 9/16” wrench.
2. Hinge tank backwards away from chassis
(Figure 8).

OPERATION
Tennant 1100 (11–99) 7
FIG. 8.
DAILY MAINTENANCE
(Every 4 Hour of Operation)
1. Clean machine with a non–abrasive, non–solvent
cleaner.
2. Rinse–out tanks and recovery dome thoroughly.
3. Remove any lint buildup from float shut–off screen
located in recovery tank. (Figure 9)
FIG. 9.
4. Remove and rinse bladder tank screen.
5. Check power cord for damage – replace if
necessary. Coil cord neatly after each use.
WEEKLY MAINTENANCE
(Every 20 Hours of Operation)
1. Flush pump system with an acetic acid solution to
dissolve normal alkaline chemical buildup.
FOR SAFETY: When using machine, follow mixing
and handling instructions on chemical containers.
a. Mix 473 ml (16 oz) of an acetic acid solution in
clean water bladder with 7.5 L (2 gal) of hot
water, 60°C (140°F) maximum.
b. Spray solution into a bucket .
c. Turn on switch.
d. Press trigger on tool until acetic acid solution
begins to spray through tips.
e. Allow solution to remain in system for up to 6
hours in above freezing temperatures.
f. Later, spray out solution into a bucket. Then
run 11 L (3 gal) of clean water through system
to flush out impurities.
2. Inspect vacuum hose for holes and loose cuffs.
3. Inspect power cord grip for damage. Replace if
damaged.
MONTHLY MAINTENANCE
(Every 80 Hours of Operation)
1. Lubricate wheels and casters with water resistant
oil.
2. Inspect machine for water leaks.
3. Inspect machine for loose screws.
EVERY 250 OF HOURS OF OPERATION
Check vacuum motor for carbon brush wear. Replace
brushes when worn to a length of 10 mm (0.38 in) or
less.
STORING MACHINE
1. Before storing machine, be certain to flush tanks
and drain machine of all water.
2. Store machine in a dry area in the upright position.
3. Remove recovery dome to promote air circulation.
ATTENTION: Do not expose to rain. Store indoors.
ATTENTION: Do not allow machine to freeze with
water in pump system, damage may occur.
Damage due to freezing temperatures is not
covered by warranty.
STORING MACHINE IN FREEZING
TEMPERATURES
1. Drain tanks thoroughly.
2. Pour 1 L (32 oz) undiluted antifreeze into solution
bladder.
3. Place a bucket under spray jets to catch spray.
4. Turn on machine.
5. Squeeze trigger on tool for 30 seconds.
6. Allow antifreeze to remain in system.

OPERATION
8Tennant 1100 (07–99)
TROUBLE SHOOTING
PROBLEM CAUSE SOLUTION
No power. Faulty ON/OFF switch Contact Service Center.
Faulty wiring. Contact Service Center.
Faulty power cord. Replace power cord.
Solution pump will not operate. Pump overheated. Determine cause and let pump cool
for 20 minutes.
Faulty switch. Contact Service Center.
Loose or broken wiring. Contact Service Center.
Faulty solution pump. Contact Service Center.
Faulty ON/OFF switch. Contact Service Center.
Poor or no vacuum suction. Vacuum thermal overload tripped. Check air flow for obstruction, wait 20
minutes for motor to cool.
Faulty ON/OFF switch. Contact Service Center.
Drain hose cap open or loose. Cap drain hose securely.
Lint clogging ball float screen. Remove recovery dome and clean lint
off screen.
Air leakage around dome. Tighten recovery dome knobs.
Vacuum hose connections are loose. Secure connections.
Damaged vacuum hose or cuffs are
loose. Replace hose or secure cuffs to hose.
Defective vacuum motor. Contact Service Center.
Worn carbon brushes. Replace brushes or call for service.
Uneven or no spray from tool. Dirty or plugged spray tips. Clean or replace tips.
y
Improper spray tip size or spray angle. Replace with proper tips.
Worn spray tips. Replace spray tips.
Loose or broken wiring. Contact Service Center.
Leaking floor tool. Quick coupler on floor tool faulty. Replace quick coupler.
g
Flow control valve leaking. Install valve rebuild kit or contact
Service Center.
Hose split or fittings loose. Replace hose and tighten fittings.
Quick coupler and plug not fully
engaged. Reconnect quick coupler.
Valve stem worn. Replace or contact Service Center.

OPERATION
Tennant 1100 (07–99) 9
SPECIFICATIONS
Model 1100
LENGTH 1070 mm (42 in)
WIDTH 330 mm (13 in)
HEIGHT 860 mm (34 in)
MACHINE WEIGHT 36Kg (80lbs)
SOLUTION BLADDER – RECOVERY TANK CAPACITY 38 ltr (10 gal) – 55 ltr (14.5 gal)
SOLUTION PUMP 120 volt, 100 psi, 1 amp
SOLUTION FLOW RATE Floor Tool/3 tips = 3.8 ltr (1 gal) per minute
127 mm (5 in) Hand Tool/1 tip = 1 ltr (32oz) per minute
VACUUM MOTOR 120 volt, 3–stage, 1.66 hp, 13 amp,1560 watts
SEALED WATER LIFT 3.5m (137 in)
DECIBEL RATING AT OPERATOR’S EAR, INDOORS ON
CARPET 80dB(A)

PARTS LIST
10 Tennant 1100 (02–97)
RECOVERY/SOLUTION TANK GROUP
3
1
41
40
5
4
2
8
9
6
7
10
11
13
12
14
15
16 17
18
19
22
21
20
23
24
27
36
28
29
31
32
34
30
37
35
26
25
38
39 33

PARTS LIST
11
Tennant 1100 (07–99)
RECOVERY/SOLUTION TANK GROUP
Ref. Part No. Description Qty.
∇1. 100103 ASM., LID, ASSEMBLY 1
2. 100109 LID, OUTER RING 1
3. 100105 LID, CENTER 1
4. 140900 SCREW, 10–24 X 3/4 6
5. 140000 WASHER, FLAT 6
6. 101714 GASKET, AIR CHAMBER 1
7. 230187 NIPPLE 1
8. 602448 STANDPIPE 1
9. 180613 FLOAT, SHUT–OFF 1
∇10. 700684 ASM., DOME 1
11. 100042 GASKET, RECOVERY DOME 1
12. 240217 KNOB, RECOVERY DOME 2
13. 140037 WASHER, NYL 2
14. 140637 NUT, WELL 10–32 2
15. 230755.BK BRACKET, CORD 1
16. 140877 SCREW, 10–32X1–1/4 2
17. 602669 SWITCH (120V) 1
18. 607728 SWITCHBOX, (1100) 1
19. 140885 SCREW, 1/4–20 X 1/2 4
20. 140328 CLAMP, NYLON 2
21. 130249 CORD, 14/4X48” 1
22. 140900 SCREW, 10–24X3/4 2
23. 130166 CORD GRIP (120V) 1
24. 130227 CORD, 16/3 X 18” (120V) 2
∇25. 701061 ASM, DRAIN HOSE STOPPER 1
26 230831 KNOB, DRAIN HOSE 1
27. 230882 STRAP, RUBBER 1
28. 140056 WASHER 1
29. 140955 PLUG 1
30. 140826 SCREW, #6 X 3/4 2
31. 140072 CLAMP, EAR 1–9/16” 2
32. 140921 SLEEVE, DRAIN HOSE 1
33. 160416 HOSE, DRAIN 1
34. 140307 CLAMP, HOSE 1
35. 230390 HINGE, TANK 1
36. 140885 SCREW, 1/4–20X1/2 1
37. 230696.BK BRACKET, DRAIN HOSE 1
38. 140227 STUD 3
39. 180628 SCREEN, TANK 1
40. 607725 TANK, RECOVERY, TEAL 1
41. 602715 BLADDER, SOLUTION 1
DECAL LIST
Ref. Part No. Description Qty.
N/S 608130 DECAL, SIDE ”1100” 2
N/S 120619 DECAL, WARNING, EXTRACTORS 1
N/S 120906 DECAL, IMPORTANT–DRAIN 1
N/S 120907 DECAL, IMPORTANT–ALWAYS CLOSE 1
N/S 120399 DECAL, DO NOT ALLOW FOAM 1
N/S 120210 DECAL, TENNANT LOGO 1

PARTS LIST
12 Tennant 1100 (02–97)
MAIN CHASSIS GROUP
24
6
1
2
345
4
7
16
28
27
30
31
32
33
29
26
25
13
12
11
10
14 15
17
18
19
20
21
22
23
9
8

PARTS LIST
13
Tennant 1100 (07–99)
MAIN CHASSIS GROUP
Ref. Part No. Description Qty.
1. 210240 NUT 1
2. 100118 GASKET, VAC MOTOR 1
3. 130996 MOTOR, VAC 5.7/3 STAGE (120V) 1
602741 CARBON BRUSHES (2/PK) 2
4. 140308 CLAMP, HOSE 2
5. 160441 HOSE, EXHAUST 2FT
6. 140501 NUT, LOCK 3
7. 130694 CORD 1
8. 103019 CAP, HUB 2
9. 103059 WHEEL 2
10. 140259 SCREW, 1/4–20X5/8 4
11. 230746 BRACKET, AXLE 2
12. 140008 WASHER, FLAT 2
13. 230739 AXLE 1
14. 25732 WASHER, FLAT 4
15. 140226 SCREW, 5/16–18X5/8 8
16. 231034 PLATE 1
17. 103004 CASTER 2
18. 140546 NUT 8
19. 140223 SCREW, 5/16–18X3/4 4
20. 140015 WASHER, LOCK 4
21. 140232 SCREW, 3/8–16X1/4 2
22. 140017 WASHER, LOCK 2
23. 231026.BK BRACKET, HANDLE 1
24. 607723 CHASSIS, TEAL 1
25. 140552 NUT 1
26 140916 CLAMP 1
27. 140000 WASHER, FLAT 4
28. 140501 NUT 4
29. 140900 SCREW, 10–24X3/4 1
30. 140889 SCREW, 1/4–20X3/4 4
31. 140016 WASHER, LOCK 4
32. 140000 WASHER, FLAT 4
33. 600451 PLATE, BLADDER 1

PARTS LIST
14 Tennant 1100 (07–99)
PUMP SYSTEM GROUP
1
2
34
56
7
8
12 14
7
8
9
13 14
7
18
19
72120
22
1716
23
24
23
10
11
25
23
26
23
27
28
13
Ref. Part No. Description Qty.
1. 150933 PLUG, QCK COUP – SER 60 1
2. 150000 ADAPTER, 1/4F X 1/4M 1
3. 140008 WASHER, FLAT, 1/2 1
4. 230489 PLATE 1
5. 150600 NIPPLE 1
6. 150511 HOSE BARB, 1/4FX3/8H 1
7. 140305 CLAMP 4
8. 160207 HOSE, 3/8 LP 3.3FT
9. 140552 NUT, LOCK NYL. 1
10. 140891 SCREW, 10–24X5/8 1
11. 140323 CLAMP, NYLON 1
12. 140519 NUT, KEP 10 – 24 3
13. 180103 PUMP, 100 PSI – 120V 1
14. 150425 ELBOW, 3/8M X 1/2H 90°2
15. 140519 NUT, KEP 10–24 2
16. 140012 WASHER, FLAT 3/16” 8
17. 140519 NUT, KEP 10–24 4
18. 160207 HOSE, 3/8 LP GRAY 2.5FT
19. 600451 PLATE, BLADDER 1
20. 140016 WASHER, LOCK 1/4” 4
21. 140000 WASHER, FLAT 4
22. 140889 SCREW, MCH 1/4–20X3/4 4
23. 140011 WASHER, FLAT 3/16 10
24. 140917 SPACER, NYLON 2
25. 607723 CHASSIS, TEAL 1
26. 140354 SCREW, 10–24X3” 2
27. 140899 SCREW, 10–24X1–1/4 2
28. 6032.6 SCREW 4

PARTS LIST
15
Tennant 1100 (07–99)
PUMP BREAKDOWN
1
2
3
4
5
6
Ref. Part No. Description Qty.
1. 190129 KIT, PRESSURE SWITCH 1
1. 190172 KIT, PRESSURE SWITCH (VITON) 1
190134 KIT, DIAPHRAGM ONLY 1
2. 190128 KIT, UPPER PUMP HOUSING 1
190124 KIT, CHECK VALVE ONLY 1
3. 190171 KIT, VALVE (VITON) 1
4. 190131 KIT, SERVICE 1
5. 190130 KIT, LOWER PUMP HOUSING 1
6. 180103 PUMP, 100 PSI 1

WIRE DIAGRAM
Tennant 1100 (07–99)
16
SOLUTION
PUMP
VACUUM
MOTOR
HANDLE
CORD
14–4 POWER
CORD
R
E
D
RED
R
E
D
R
E
D
B
L
A
C
K
W
H
I
T
EGREEN
BLACK
BLACK
WHITE
GREEN
MAIN
SWITCH
GREEN
G
R
E
E
N
BLACK
W
H
I
T
E
B
L
A
C
K

OPTIONAL PARTS
17
Tennant 1100 (02–97)
127 mm (5 in) HAND TOOL
10
211
12
13
9
8
5
4
36
1
7
Ref. Part No. Description Qty.
200505 TOOL, HAND (COMPLETE) 1
1. 200431.BK TOOL, HAND 1
2. 150913 COUPLER, QUICK (SER. 60) 1
3. 150615 NIPPLE, CLOSE 1
4. 200905 TRIGGER, HAND TOOL 1
5. 210210 VALVE, FLOW CONTROL 1
6. 190600 VALVE PIN & SPRING (NOT SHOWN) 1
7. N/A CAP, VALVE 1
8. 150606 NIPPLE, HEX 1/4 1
9. 150403 ELBOW, ST 1/4 45°1
10. 200992 BODY, SPRAY 1/4F 1
11. 200996 SCREEN, SPRAY NOZZLE 1
12. 200965 TIP, SPRAY #8002 1
13. 200994 CAP, SPRAY BODY 1
SOLUTION AND VACUUM HOSES
1
2
4
4
3
5
6
7
Ref. Part No. Description Qty.
1. 160185 HOSE, SOLUTION 15’ 1
1. 160186 HOSE, SOLUTION 25’ 1
2. 150913 COUPLER, QUICK SER. 60 1
3. 150933 PLUG, QUICK COUPLER 1
4. 150615 NIPPLE 2
5. 160400 HOSE, VACUUM 15’ W/ CUFFS 1
5. 160401 HOSE, VACUUM 25’ W/ CUFFS 1
6. 160430 CUFF, HOSE 1–1/2” 2
7. 160451 CONNECTOR, VACUUM HOSE 1–1/2” 1

OPTIONAL PARTS
18 Tennant 1100 (10–96)
FLOOR TOOL
3
1
2
5
46
7
8
10
11
9
12 13 14
15
16
17
20 21
22
19
23
24
25
18
26
27
Ref. Part No. Description Qty.
600048 FLOOR TOOL W/ S.S. SHOES (COMPLETE) 1
1. 200403.BK TOOL, FLOOR 1
2. 200939 SHOES, S/S, FLOOR TOOL 2
3. 200927 GRIP, ADJUSTABLE (COMPLETE) 1
4. 200912 FOAM, GRIP 1
5. 140259 SCREW, 1/4X3/4 2
6. 200902 TRIGGER, FLOOR TOOL 1
7. 200809 SLEEVE, TRIGGER 1
8. 140605 PIN 1
1405202–970 NUT, PUSH (NOT SHOWN) 2
9. 210150 VALVE, FLOW CONTROL 1
10. 190603 KIT, VALVE PIN & SPRING 1
11. N/A CAP, HEX, VALVE 1
12. 150403 ELBOW, 1/4–45°1
13. 150615 NIPPLE, CLOSE 1/4 1
14. 150913 COUPLER, QUICK SER. 60 1
15. 160170 HOSE, SOLUTION, LP 1
16. 150606 NIPPLE, HEX 1/4” 1
17. 140058 WASHER 1
∇18. 700062 ASM., SPRAY BAR 1
19. 150700 CROSS 1
20. 150600 NIPPLE 2
21. 150401 ELBOW, 901/4FX1/4F 2
22. 200993 SPRAY BODY 3
23. 200996 SCREEN, SPRAY BODY 3
24. 200964 TIP 3
25. 200994 CAP, SPRAY BODY 3
26. N/A PLATE, GLIDE 3
27. N/A END FASTENERS 3