Tennant 9045218 Training manual

IB 9045218 (12- 2021) 1
INSTRUCTION BULLETIN
No. 9045218
Machine: S16
Published: 12- 2021
Rev. 00
NOTE: DO NOT DISCARD the Parts List from the Instruction Bulletin. Place the
Parts List in the appropriate place in the machine manual for future
reference. Retaining the Parts List will make it easier to reorder
individual parts and will save the cost of ordering an entire kit.
NOTE: Numbers in parenthesis ( ) are reference numbers for parts listed in Bill of Materials.
Installation instructions for kit number 9045202
Kit installation must be performed by TennantTrue

service or an authorized service provider.
SYNOPSIS:
This kit contains the parts needed to install a deluxe seat on S16 sweepers.
Please follow step-by-step instructions.
SPECIAL TOOLS / CONSIDERATIONS: NONE
(Estimated time to complete: 1 hour)
PROTECT THE ENVIRONMENT
Please dispose of packaging materials, used machine components
such as batteries and fluids in an environmentally safe way according
to local waste disposal regulations.
Always remember to recycle.
PREPARATION:
FOR SAFETY: Before leaving or servicing
machine, stop on level surface, turn off
machine, and remove key.
1. Lift the operator seat open and secure the
seat into the fully open position.
2. Disconnect the battery cable from the
machine.
WARNING: Always disconnect battery
cables from machine before working on
electrical components.
3. Disconnect the wire harness from the seat
switch. (Fig. 1)
FIG. 1

IB 9045218 (12- 2021)2
4. Remove the hardware securing the upper
operator platform to the seat channel and
carefully lift the upper operator platform/
operator seat from the seat channel. Set all
mounting hardware aside. (Fig. 2)
FIG. 2
5. Remove the operator seat from the upper
operator platform. Set the upper operator
platform aside. Discard the operator seat and
all mounting hardware.
INSTALLATION:
1. Install the seat switch (24) into the operator
seat (22). (Fig. 3)
2. Use two pan screws (26) and two spacers
(25) to install the adjustable slide track (30)
onto the operator seat (22). (Fig. 3)
3. Use two pan screws (26) and two spacers
(25) to install the slide track (29) onto the
operator seat (22). (Fig. 3)
FRONT
22
23
29
25
26
24
30
25
25
26
25
26
26
FIG. 3

IB 9045218 (12- 2021) 3
FRONT
2
3
27
Seat
channel Seat spring
mounting
bracket
Mounting
plate
FIG. 4
4. Use one ball stud (2) to install the gas spring
(3) onto the seat channel. (Fig. 4)
5. Use another ball stud (2) and hex nut (27) to
install the gas spring (3) onto the seat spring
mounting bracket. (Fig. 4)

IB 9045218 (12- 2021)4
FRONT
5*
6*
7
8*
9*
10
11*
12
13
14
15
16
17 18
19
20
21
1
Seat
channel
Mounting
plate
*NOTE: Use jam nuts (11) to adjust latch angle
(9) and loosen M5 hex screws (6)/M5 hex nuts
(8) to adjust position of latch (5) in slotted holes
in seat channel. Tighten M5 hex screws/M5 hex
nuts when finished adjusting latch.
FIG. 5
6. Use two M5 hex screws (6), two flat washers
(7), and two M5 hex nuts (8) to install the
latch (5) onto the seat channel. (Fig. 5)
7. Install the yellow handle grip (1) onto the seat
latch handle (15). (Fig. 5)
8. Press both nylon snap in bushings (14) into
the latch bracket (12). (Fig. 5)
9. Insert the latch handle (10) through the nylon
snap in bushings (14) pressed into the latch
bracket (12) in the previous step. (Fig. 5)
10.Thread one hex jam nut (11) onto the latch
handle (10). (Fig. 5)
11. Insert the latch angle (9) onto the latch handle
(10) and thread the remaining hex jam nut
(11) onto the latch handle to secure the latch
angle. (Fig. 5)
12.Orient the notch in the seat latch handle (15)
onto the latch handle (10) and use one
SEMS M6 hex screw (1), one sleeve (20), one
flat washer (21), and one M6 hex nut to install
the seat latch handle (15) onto the latch
bracket (12). (Fig. 5)
13.Use one cotter pin (17) and one flat washer
(16) to secure the latch handle (10) inside the
seat latch handle (15). (Fig. 5)
14.Install the latch angle (9) onto the latch (5)
and use two SEMS M8 hex screws (13) to
install the seat latch assembly assembled in
the previous steps onto the seat channel.
(Fig. 5)
15.Close the seat channel onto the machine and
adjust hardware so the latch (5) secures the
seat channel closed and allows the seat
channel to be opened/raised when the handle
is pulled to release the seat channel. (Fig. 5)
16.Use four hex nuts (27), four flat washers (28),
and four bolt retention nuts (4) to install the
operator seat (22) onto the upper operator
platform. (Fig. 6)
17.Use saved hardware to install the operator
platform/operator seat (22) onto the seat
channel. (Fig. 6)
18.Connect the wire harness to the seat switch
(29). (Fig. 6)
19.Reconnect the battery cable to the machine.

IB 9045218 (12- 2021) 5
FRONT 23
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
29
25
27
27
24
30
25
25
26
28
27
1
26
25
31
31
Upper operator
platform
Seat channel
4
4
4
FIG. 6

IB 9045218 (12- 2021)6
Bill Of Materials For Seat Kit, Deluxe, CI [S16] - 9045202
Ref.
Tennant
Part No. Description Qty.
11202957 Grip, Handle, .25d .60l Yel 1
2 1012878 Stud, Ball, .39d .31- 18 2
3 14464 Gas spring, 35lb, 8.0strk 1
4 1077073 Nut, Push, Bolt Retention, Stl, 5/16 Thrd 4
5 1025736 Latch 1
624199 Screw, Hex, M5 X 0.80 X 16, SS 2
7 19065 Washer, Flat, 0.19b 0.44d .05, Pl, 08 2
8 09739 Nut, Hex, Lock, M5 X 0.80, Nl, SS 2
9 1200999 Angle, Latch 1
10 1203958 Handle, Latch 1
11 32520 Nut, Hex, Jam, .25- 20 2
12 1203946 Bracket Wldt, Latch 1
13 1020341 Screw, Hex, M8 X 1.25 X 20, SS, SEMS 2
14 80921 Bushing, Snap- In, 0.25b 0.31d 0.08th Nyl 2
15 1253493 Handle Wldt, Latch, Seat 1
16 01684 Washer, Flat, 0.27b 0.69d .05, SS 2
17 08085 Pin, Cotter, Hair, 0.31d .058 Wir 1
18 08712 Nut, Hex, Lock, M6 X 1.00, Nl, SS 1
19 1034731 Screw, Hex, M6 X 1.00 X 16, SS, SEMS 1
20 1205764 Sleeve, P/M, 0.25b 0.38d 0.1l [430ss] 1
21 29570 Washer, Flat, 0.28b 1.00d .06, Stl 1
o22 1201428 Seat, Dlx, W/ Armrests & Orange Seatbelt 1
Y23 1248442 Seatbelt, Orange, Retractable, Afmkt 1
Y24 1048955 Switch, Seat, No [Delta 6440- 04] 1
25 1051052 Spacer, Rnd, .38b .88d .38l 4
26 1073048 Screw, Pan, Phl, .31- 18 X 1.50, G2 4
27 32983 Nut, Hex, Lock, .31- 18, Nl 5
28 1017218 Washer, Flat, 0.32b 1.00d .12, SS 4
29 1077067 Track, N- Lkg, Seat, 12.5l, No Stud 1
30 1077071 Track, Locking, 12.5l, No Stud w/Handle 1
31 76955 Screw, Hex, .31- 18 X 1.00, G5 4
TENNANT COMPANY
10400 Clean Street
Eden Prairie, MN 55344- 2650