Tennsco 1991008 Instruction Manual

RETAIN INSTRUCTIONS FOR FUTURE REFERENCE!
PK-1991008
ASSEMBLY INSTRUCTIONS & PARTS MANUAL #1991008
Tennsco Corp., Dickson, TN 37056-1888 • [phone]
LIMITED WARRANTY
Tennsco warrants goods purchased hereunder to be free of defects in materials and workmanship for a period of one (1) year from the date of shipment,
hereunder. This warranty shall not apply in the event goods are damaged as a result of misuse, abuse, neglect, accident, improper application, modification
orrepairbypersonsnotauthorizedbySeller,wheregoodsaredamagedduringshipment,orwherethedatestampsonthegoodshavebeendefaced,modified
or removed. UNLESS CONSIDERED UNENFORCEABLE OR UNLAWFUL UNDER APPLICABLE LAW:
a. ALL IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO WARRANTIES OR MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE ARE HEREBY EXCLUDED:
b. BUYERS REMEDY, IF ANY, FOR ANY DEFECTIVE GOODS SHALL BE LIMITED TO A REFUND BY SELLER OR REPLACEMENT OF THE
GOODS AT SELLER’S OPTION, AND SHALL IN NO EVENT INCLUDE DAMAGES OF ANY KIND, WHETHER INCIDENTAL, CONSEQUENTIAL
OR OTHERWISE.
NO GOODS ACCEPTED FOR RETURN WITHOUT PRIOR APPROVAL. Seller shall have the right to inspect any goods claimed to be defective at Buyers
place of business or require Buyer to return the goods to Seller for inspection on Seller’s premises. Transportation charges covering returned goods will
be borne by Seller only if such goods are proven to be defective, are covered by this warranty and are returned within the warranty period stated above.
TENNSCO CORP., P.O. BOX 1888, DICKSON, TN 37056-1888
[phone] [phone]
Z-Line Record Archive Storage System
Installation Instructions
Congratulations on your purchase of
a Z-Line Record Archive Storage
System from Tennsco! Z-Line's
interlocking keyhole design not only
makes installation fast and easy but
eliminates the need for clips,
gussets, sway braces or other
hardware commonly used in
conventional shelving, allowing
completely free access to your
stored materials from all sides of
the unit. And our particleboard
decking recesses inside the deck
supports, reducing the overall profile
for greater storage.
Z-Line Record Archive Storage is
available in 60" and 84" heights, 42"
and 69" widths, and 15" (single
entry) and 30" (double entry) depths.
And starter and adder units allow for
joining shelving units together.
GENERAL SAFETY INFORMATION
Some parts may have sharp edges.
CARE must be taken when handling
the pieces to avoid injury. For safety,
wear a pair of work gloves when
assembling or performing any
maintenance on shelving.

3. With help from an associate, or using a wall for
support, connect two EUR uprights (Ref. No. 1a)
using two front-to-back supports (Ref. No. 2), one
at the top and one near the bottom (you should
leave the bottom-most
keyhole slot empty).
Be sure the
front-to-back
supports are
fully seated
in the key-
hole slots,
as shown.
NOTE: The
uprights must
be positioned
so that the
narrow part
of the slots
is toward the
floor, as shown
in the inset at right.
Tool Needed: A rubber mallet for seating the shelf supports into the uprights.
Two people are recommended for assembly. Approximate assembly time: 15 to 30 minutes per section.
ASSEMBLY OF ARCHIVE SHELVING
4. Repeat the instructions in step 3 to construct a
second set of unit ends.
NOTE: If you are planning to install an adder
unit, this second set of
uprights should consist
of ZTP uprights
(Ref. No. 1b)
so that
adjacent
sections can
be tied
together.
Carefully
review step 2
and step 9
to better
understand
this.
2. Depending upon
whether you ordered
a single unit or an
adder unit, you may
have one or both of
the styles of upright
shown at right:
Angle
Post (EUR)
"T" Post
(ZTP)
B. Two or more units with Angle Posts (EUR) on each
end and "T" Posts (ZTP) as intermediate uprights.
1. The reference numbers used throughout this
sheet refer to the illustration on the back cover.
This is to help you to identify the various parts
as they are mentioned.
5. With the help of an associate, connect the two
unit ends with left-to-right shelf supports (Ref.
No. 3). Again, be
sure that
the flat
surface of
the shelf
support is
facing up,
and that
the shelf
supports
are fully
seated,
as was
illustrated
in step 3.
A single unit will use EUR posts for all four
uprights, as shown below in Figure A. If you plan
on installing an adder unit, however, you should
build your starter unit with two ZTP
posts on one end
(which will join
with the adder),
as shown in
Figure B.
NOTE: Inset is shown
from opposite side.
IMPORTANT: Support
MUST be inserted so
the flat surface is on
top as shown in pro-
file at left!
A. Single unit with
fourAnglePosts(EUR).

7. Shelf deck supports (Ref. No. 4) are necessary for
30" deep units only. Attach shelf deck supports by
inserting the metal prongs on the deck support into
the slots on the shelf supports. 69" x 30" units
require two shelf deck
supports per level (as
shown below);
42" x 30" units
require only
one shelf
deck support
per level,
placed in
the center.
8. If particleboard
decking (Ref.
No. 5) was ordered,
place the decking
on each shelving
level. The
decking should
fit flush inside
the shelf
supports.
If you have
purchased a
single unit,
your shelving
unit is now
complete.
For adder
units, see
step 9.
6. Attach the remaining shelf supports at the desired
shelf levels, making sure that all shelf supports
are completely
seated in the
upright slots.
NOTE: For
archive
storage
boxes to fit
stacked two-
high per
level, there
should be a
minimum of
16 holes
between
shelf
supports. We
recommend
placing the
bottom shelf
support rivet in the
2nd, 19th, 37, and 55th holes
on 84" high units, (shown above)
and in the 2nd, 20th, and 39th holes on 60" units. 9. If joining more than
one unit together, your
original unit should have been
assembled with ZTP uprights on one end, as
described in step 4. Simply
continue adding shelf
supports and uprights
to complete your
additional units.
Holes
55 & 56
Holes
37 & 38
Holes
19 & 20
Holes
2 & 3

REF.
NO. PART NO.
DESCRIPTION 60" HIGH UNITS
1a Angle Post (Single or Starter Units Only) 4 EUR-60 4 EUR-60 4 EUR-60 4 EUR-60
1b "T" Post (Adder Units Only) 2 ZTP-60 2 ZTP-60 2 ZTP-60 2 ZTP-60
2 Front-To-Back End Support 6 VDRS-1516 6 VDRS-3016 6 VDRS-1516 6 VDRS-3016
3 Left-To-Right Shelf Support 6 VDRS-4216 6 VDRS-4216 6 VDRS-6914 6 VDRS-6914
4 Shelf Deck Support -- ------------ 3 FBSV-30 -- ------------ 6 FBSV-30
5 Optional Particleboard Decking 3 PB-4215 3 PB-4230 3 PB-6915 3 PB-6930
84" HIGH UNITS
1a Angle Post (Single or Starter Units Only) 4 EUR-84 4 EUR-84 4 EUR-84 4 EUR-84
1b "T" Post (Adder Units Only) 2 ZTP-84 2 ZTP-84 2 ZTP-84 2 ZTP-84
2 Front-To-Back End Support 8 VDRS-1516 8 VDRS-3016 8 VDRS-1516 8 VDRS-3016
3 Left-To-Right Shelf Support 8 VDRS-4216 8 VDRS-4216 8 VDRS-6914 8 VDRS-6914
4 Shelf Deck Support -- ------------ 4 FBSV-30 -- ------------ 8 FBSV-30
5 Optional Particleboard Decking 4 PB-4215 4 PB-4230 4 PB-6915 4 PB-6930
REPLACEMENT PARTS
Tennsco makes every effort to ensure that all units ship complete with all parts and arrive undamaged.
However, should your unit contain missing or damaged parts, replacements may be obtained directly from
Tennsco. To obtain proper replacement parts, follow the instructions below:
!!
!!
!
!!
!!
!
!!
!!
!
!!
!!
!
!!
!!
!
!!
!!
!
!!
!!
!
TO OBTAIN PROPER REPLACEMENT PARTS, PLEASE PROVIDE THE FOLLOWING INFORMATION:
Description of part(s) needed and part Purchase Date
number(s) as shown in Parts List (above) Your company name
Color (i.e. Medium Grey, etc.) Contact person's name
Was item missing, or was it damaged? Who the product was purchased from
Tennsco Corp., P.O. Box 1888, Dickson, TN 37056-1888 Voice: [phone] Fax: [phone]
If requesting parts by telephone, ask for customer service and have as much of the above information ready as possible.
EUR Upright
(Ref. No. 1a)
Front to
Back End
Support
(Ref. No. 2)
Particleboard
Decking
(Ref. No. 5)
Left-To-Right
Shelf Support
(Ref. No. 3)
ZTP Upright
(Ref. No. 1b)
QTY.
42"w x 15"d PART NO.
QTY.
42"w x 30"d PART NO.
QTY.
69"w x 15"d PART NO.
QTY.
69"w x 30"d
Shelf Deck Support
(Ref. No. 4)