Teradek Ace 500 User manual

Transmitter/Receiver Kit
Ace 500
Quick Start Guide

PHYSICAL PROPERTIES
A: Link status LED
B: Video status LED
C: Power status LED
D: HDMI input
E: 7-17V DC input
F: Reset/Pairing button
G: Mini USB port
H: HDMI output
I: Menu joystick
F
E
D
Ace 500 - TX
Ace 500 - RX
C
H
E
A
B
F
G
G
C
B
A
I
TX Side

TABLE OF CONTENTS
Power and Connect ............................. 2
Device Operation ................................ 2
Custom 3rd Party Cables ..................... 3
Mounting............................................ 4
On-Screen Display (OSD) Operation ...... 5
Bolt Manager ..................................... 6

2
2
Connect the output from your video source to the HDMI input (D) on the Ace transmitter. Connect
the HDMI output (H) from the Ace receiver to the video input on your monitor.
1
POWER AND CONNECT
Connect power to the Ace transmitter from a compatible battery using the included P-Tap to barrel
cable. Power the Ace receiver with the included A/C adapter, or if Ace is equipped with a battery plate
accessory, connect a compatible battery (Sony L-series or LP-E6).
DEVICE OPERATION
• Keep the transmitter and receiver at close range for 60 seconds after powering on the devices. This
allows them to scan for and select the best wireless channel.
• For best results when using multiple Ace systems in the same area, place the transmitters and
receivers a few feet apart from each other.
• Operation of other wireless equipment may interfere with Ace. Try to separate other wireless
transmitters and receivers as much as possible.

3
• Test the power cable polarity with ONLY the power cable connected to Ace.
CAUTION: Using a reverse polarity or improperly−constructed power cable can damage the
product and is not covered under warranty.
• Check the power cable for shorts and proper grounding.
• Do not connect video cables.
CUSTOM/THIRD PARTY CABLES
BOLT MANAGER
• SELECT REGION - Configure Ace 500 to comply with your region’s regulations governing use of
the 5GHz spectrum.
Bolt Manager allows you to configure, pair, and upgrade the Ace system. Bolt Manager is available as
software for Mac and Windows at www.teradek.com/pages/downloads, or for purchase as a standalone
device.
The following configuration settings are available:
• SELECT TX NAME (TRANSMITTER ONLY) - Modify the transmitter’s name to make it easier to
identify among other systems that are present.

4
• Mount the transmitter vertically, keeping the antennas
clear of any obstructions.
• For best results, orient the transmitter antennas
so each one has clear line−of−sight to the receiver.
• DO NOT OVERTIGHTEN
SCREWS INSERTED INTO
THE TRANSMITTER’S /”- THREADED HOLE.
Doing so can damage the transmitter’s chassis and
internal components, voiding the warranty.
Ace has a 1/4”-20 threaded hole on the bottom for mounting on a light stand adapter or any other
mounting accessory.
MOUNTING
CAUTION:
Ace 500 receiver
can be mounted
vertically on a light
stand or monitor.
Ace 500 transmitter can
be mounted vertically
on a camera

5
Receiver Status Screens - Connect your receiver to a monitor and activate the OSD (On-screen
display) by depressing the Menu joystick button (I), then cycle through screens by pressing the button up,
down, left, or right.
ON-SCREEN DISPLAY (OSD) OPERATION
• Main Status Screen - This screen displays the status of the wireless receiver, along with the current
video resolution, frequency, link quality (if connected).
• Temperature Status Screen - Displays the current internal temperature of the unit.
Menu Operation - Launch the menu by pressing right on the joystick while the OSD is active. Exit
from the menu by pressing left.
• Test Pattern - Select a video output format from this menu to output a test pattern over SDI.
Return to the previous video by pressing left on the Menu joystick.
• Pairing - Link your receiver with another transmitter. Once pairing is activated on the receiver, turn
on the transmitter and use a paper clip to hold the reset button (F) for one second and release. The red
warning LED and link LEDs will blink to indicate that pairing is active.
• OSD Settings - Choose when to display the OSD. By default, the OSD is displayed when the link
is down. Hidden by default hides the OSD until it is activated by the joystick. If Always show OSD
is selected, the OSD will be displayed unless deactivated by the joystick.
• Reset All Settings - Reset all configurable options to their factory defaults.
• Device Info - Displays the model and serial number.

6
Teradek regularly releases new firmware versions to improve performance, add new features, or to fix vulnerabilities.
Teradek.com/pages/downloads contains all the latest firmware and software updates.
Visit support.teradek.com for tips and information, or to submit a request for support to our team.

7
© 2020 Teradek, LLC. All rights reserved. v1.3