Teraoka AP-3001g User manual

COPYRIGHT © 2005 TERAOKA WEIGH-SYSTEM PTE LTD
SERVICE MANUAL
AP-3001g
IEEE 802.11a/b/g/n 2x2 Wireless LAN USB Client
AP-3001g
Tentative Edition

Table of Content
i) Notice.................................................................................................................................................1
ii) Safety Information..............................................................................................................................2
iii) Safety Regulations.............................................................................................................................2
1. General.............................................................................................................................................................4
1.1 Model Specification............................................................................................................................4
1.2 Operating Specification......................................................................................................................4
2. Enclosure Dimension .....................................................................................................................................5
3. AP-3001g Setup Diagram & Procedures.......................................................................................................6
3.1 Setup Diagram......................................................................................................................................6
3.2 Setup Procedures.................................................................................................................................6
4. Revision Records............................................................................................................................................9

1
i) Notice
The material contained in this document is proprietary and for information only and is subject to change without
notice. Teraoka Weigh-System assumes no responsibility for any errors or damages arising from
misinterpretation of any procedure.
Screen displays, operating procedures and supporting features might vary with different software version
releases.
This document shall not be reproduced whether in part or whole without the written consent from Teraoka
Weigh-System Pte Ltd.
Teraoka Weigh-System Pte Ltd
4, Leng Kee Road
#06-01 SIS Building
Singapore 159088

2
ii) SafetyInformation
The operator of the equipment shall comply with the safety and warning indications and procedures outlined in
this document. Teraoka Weigh-System Pte Ltd assumes no responsibility or liability for failure to comply with
these requirements.
• Repair and servicing of product, shall only be carried out by trained and qualified personnel.
Disclaimer:
Specifications are subject to change without notice. All dimensions shown are approximate. Please be aware
that Teraoka has indicated that its hardware and software used in the product may require additional updates in
the future as our product is continually under development. The need for such updates most likely applies to the
Printer software.
CAUTIONS:
FOR
PLUGGABLE EQUIPMENT
,
THAT THE SOCKET
-
OUTLET SHALL BE INSTALLED NEAR THE
EQUIPMENT AND SHALL BE EASILY ACCESSIBLE.
POUR LE MATÉRIEL RACCORDÉ PAR PRISE DE COURANT, LE SOCLE DE PRISE DE
COURANT DOIT ÊTRE
INSALLÉ À PROXIMITÉ DU MATÉRIEL ET DOIT ÊTRE AISÉMENT ACCESSIBLE.
FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME TYPE
AND RATING OF FUSE.
POUR NE PAS COMPROMETTRE LA PROTECTION CONTRE LES RISQUES D’INCENDIE,
REMPLACER PAR UN FUSIBLE DE MÊME TYPE ET DE MÊME CARACTÉRISTIQUES
NOMINALES.
DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED. REPLACE ONLY WITH
THE SAME OR EQUIVALENT TYPE RECOMMENDED BY THE MANUFACTURER. DISCARD
USED BATTERIES ACCORDING TO THE MANUFACTURER’S INSTRUCTIONS
IL Y A DANGER D’EXPLOSION S’IL Y A REMPLACEMENT INCORRECT DE LA BATTERIE.
REMPLACER UNIQUEMENT AVEC UNE BATTERIE DU MÊME TYPE OU D’UN TYPE
RECOMMANDÉ PAR LE CONSTRUCTEUR. METTRE AU RÉBUT LES BATTERIES USAGÉES
CONFORMÉMENT AUX INSTRUCTIONS DU FABRICANT.
iii) SafetyRegulations
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.

3
- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
This device is operating in 5.15~5.25GHz frequency range in indoor environment only.
Industry Canada statement:
This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired
operation.
IMPORTANT NOTE:
Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
This device is operating in 5.15~5.25GHz frequency range in indoor environment only.
Le present appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts
de license. L'exploitation est autorisee aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioelectrique subi, meme si le brouillage est
susceptible d'en compromettre le fonctionnement.
IDA Compliance Statement: (Singapore)
This equipment registered to comply with IDA (Info-Communications Development Authority of Singapore)
Standard under Dealer’s Class License.
For Taiwan 警語：
依NCC低功率電波輻射性電機管理辦法規定
經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加
大功率或變更原設計之特性及功能。
低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用
，並改善至無干擾時方得繼續使用。前項合法通信，指依電信法規定作業之無線電通信。低功
率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾
The device could automatically discontinue transmission in case of absence of information to transmit,
or operational failure. Note that this is not intended to prohibit transmission of control or signalling information
or the use of repetitive codes where required by the technology.

AP-3001G Service Manual
4
1. General
1.1 ModelSpecification
Model
:
AP-3001g
Brand Name
:
Teraoka
Network Standard
:
IEEE 802.11 a/b/g/n compliant
Dimensions (in mm)
:
Body Casing
Dimension -
90(L) x 30(W) x 9.5(H)
Color
:
White
USB Cable Length
:
1.5 meters (High Speed USB 2.0 Cable with USB Connector
Type A)
Weight
:
100g approx.
Operating System
:
Linux
Supported OS
:
Driver support for Windows 7, 2000, XP, Vista and Linux OS
Power Source
: Host PC/USB
Voltage & Current
: 5VDC, 500mA
Operating Temperature
Ranges
: 10ºC to +40ºC
Operating Humidity : 85% Max. Non-condensing
USB Interface : Support USB 2.0
Housing Material : Plastic ABS
1.2 OperatingSpecification
Power Source
:
5VDC +/-10% Supplied from the Host/PC USB
Operating Tempera
ture
:
10ºC to +40ºC
Humidity
:
85% Max. Non-condensing

AP-3001G Service Manual
5
2. Enclosure Dimension

AP-3001g Service Manual
6
3. AP-3001g Setup Diagram & Procedures
3.1 SetupDiagram
Note: **
This equipment is used for professional environment. AP-3001g should be installed and operated with minimum
distance 20cm between the radiator & your body.
3.2 SetupProcedures
1. Disable the Wireless Network Connection (Wireless adapter) from your PC.
Go to Control Panel >Network and Internet>Network and Sharing center>View network status and task>Change
Adapter settings. Then right click the “Wireless Network Connection” and select “Disable".
USB Cable connection
USB Host PC/Devices
AP-3001g **
Access Point

AP-3001g Service Manual
7
2. Attach the AP-3001g directly into a USB port on your PC. The AP3001g driver will auto run
and install to your PC. A new wireless adapter “Wireless Network Connection” will show.
Remark:
Contact your supplier for the technical support, if the driver is required to install manually to support
your PC/Host USB equipment.
3. Click on “Wireless Network Connection 2”, and select your desired Access Point to
performance wireless connection.
USB Host PC/Devices
AP-3001g **

AP-3001g Service Manual
8
4. If you are not able to “enable” your wireless Network Connection, you can “Diagnose” your
wireless adaptor, and select “Apply this fix” for resolving the problems.
Select “Diagnose”
Select “Apply this fix”
Close Windows after Troubleshooting has completed

AP-3001g Service Manual
9
4. Revision Records
Serial
No. Date
Edition
Status Description of Changes
Software
Version
Remarks
001