Tesla Cybertruck Crossbars User manual

Cybertruck Crossbars
Owner’s Manual
Barres transversales pour Cybertruck
Manuel de l'utilisateur
Barras transversales Cybertruck
Manual del propietario

Contents
1. 2x keys
2. 1x torque wrench
3. 2x crossbars
4. 8x M6 nuts
5. 8x striker plates
02

R8A9N1D
CAR WASH
220 lbs
(100 kg) 220 lbs
(100 kg)
220 lbs
(100 kg)
220 lbs (100 kg) per 2-crossbar set
Maximum Weight
100 kg (220 lbs) par jeu de 2 barres transversales
Poids maximum
220 lb (100 kg) por cada conjunto de 2 barras transversales
Peso máximo
440 lbs
(200 kg)
s
kg)
03
Remove the crossbars before
entering an automatic car wash.
Retirer les barres transversales avant d’entrer
dans une station de lavage automatique.
Quite las barras transversales antes de
ingresar a una estación lava autos.

04
Identify the location of the 8 applique
doors.
1
Open all 8 applique doors.
8x
2
With the supplied torque wrench,
loosen and remove the nuts located
within the applique doors over the
vehicle’s roof. Set the nuts aside. For
applique doors over the vehicle’s
truck bed, set aside the 8 nuts
supplied in the rack’s hardware bag.
NOTE: The nuts removed in this step
must be reinstalled on the vehicle if
the striker plates installed in step 4
are later removed from the applique
doors over the vehicle’s roof.
8x
3

Instructions (continued)
05
8x
4Position the striker plate so that the
raised arrow on it is directed outward,
away from the vehicle. Align it with
the threaded studs and carefully set it
in place. Utilize the torque wrench to
secure the nuts that were previously
set aside back onto the threaded
VWXGV7LJKWHQHDFKQXW´UPO\XQWLO
reaching a torque of 7.8 Nm. Once the
torque wrench produces an audible
click, it indicates that the desired
torque has been achieved. NOTE:
Install all 8 striker plates now so that
you have the option to move your
crossbars to other locations if desired.
5
Once the towers are completely
seated, close the tower doors
securely. You will hear a “click” when
the tower door is closed completely.
NOTE: If there is resistance to closing
or if the door physically cannot be
closed, the clip is not seating properly.
To resolve this, open the door, re-seat
the tower, push down, and try again.
6
This step requires two people. Locate
the “FRONT” arrow embossed on the
bottom of the crossbar’s rubber pad
and orient it towards the front of the
vehicle. Lower one tower onto the
striker plate and extend the crossbar
so that the other tower aligns with the
striker plate on the opposite side. Use
a key to unlock the tower covers and
open the tower doors. Push down to
seat both towers.

Instructions (continued)
06
Repeat steps 5 and 6 to install your
second crossbar at the desired
location.
7
To test the secure installation of
the crossbars, vigorously pull in
all directions. If any movement is
observed at any of the four towers,
repeat steps 5 and 6, and then retest
the installation.
8

After driving 12 miles
After driving 30 miles
Check each mounting point.
Check each mounting point.
Check each mounting point.
R8A9N1D
07
&KHFNDWWDFKPHQWKDUGZDUHDQGORDGIRUWLJKW´WDQGIXQFWLRQ
• %HIRUHWKHVWDUWRIDQ\MRXUQH\
• $IWHUGULYLQJDVKRUWGLVWDQFHPLOHVRUPLQXWHVIROORZLQJUDFNRUORDGLQVWDOO
• $WUHJXODULQWHUYDOVRQORQJHUMRXUQH\V
• (YHU\WZRKRXUVRQEDGWHUUDLQ
• $IWHULQWHUUXSWLRQRIDMRXUQH\GXULQJZKLFKWKHYHKLFOHZDVOHIWXQVXSHUYLVHGFKHFNIRUGDPDJHGXH
WRRXWVLGHLQWHUYHQWLRQ

Rack Installation
,QDGHTXDWHO\VHFXUHGORDGVDQGLQFRUUHFWO\PRXQWHGURRI
UDFNVDQGDFFHVVRU\UDFNVFDQFRPHORRVHGXULQJWUDYHODQG
FDXVHVHULRXVDFFLGHQWV7KHUHIRUHLQVWDOODWLRQKDQGOLQJ
DQGXVHPXVWEHFDUULHGRXWLQDFFRUGDQFHZLWKSURGXFWDQG
YHKLFOHLQVWUXFWLRQV
,QDGGLWLRQWRWKHVHLQVWUXFWLRQVUHYLHZWKHPRXQWLQJ
LQVWUXFWLRQVIRUWKHURRIUDFNDQGWKHRSHUDWLQJLQVWUXFWLRQV
RIWKHYHKLFOH
7KHVHLQVWUXFWLRQVVKRXOGEHNHSWWRJHWKHUZLWKWKHYHKLFOHV
RSHUDWLQJLQVWUXFWLRQVDQGFDUULHGLQWKHYHKLFOHZKHQLQXVH
DQGHQURXWH
)RU\RXURZQVDIHW\\RXVKRXOGRQO\XVHWHVWHGHJ*6
WHVWHGURRIUDFNVWKDWDUHDXWKRUL]HGIRUXVHZLWK\RXU
YHKLFOH
&KHFNDWWDFKPHQWKDUGZDUHDQGORDGIRUWLJKW´WDQG
IXQFWLRQ
• %HIRUHWKHVWDUWRIDQ\MRXUQH\
• After driving a short distance (30 miles or 30
PLQXWHVIROORZLQJUDFNRUORDGLQVWDOO
• $WUHJXODULQWHUYDOVRQORQJHUMRXUQH\V
• (YHU\WZRKRXUVRQEDGWHUUDLQ
• $IWHULQWHUUXSWLRQRIDMRXUQH\GXULQJZKLFKWKH
YHKLFOHZDVOHIWXQVXSHUYLVHGFKHFNIRUGDPDJHGXH
WRRXWVLGHLQWHUYHQWLRQ
Rack Loading
'RQRWH[FHHGWKHPD[LPXPORDGVSHFL´HGIRUWKHURRIUDFN
DFFHVVRU\UDFNRUWKHPD[LPXPORDGUHFRPPHQGHGE\WKH
YHKLFOHPDQXIDFWXUHU
Max Roof Load = weight of roof rack + weight of accessory
racks + weight of load.
/RDGVKDOOEHXQLIRUPO\GLVWULEXWHGZLWKWKHORZHVWSRVVLEOH
FHQWHURIJUDYLW\
/RDGVKRXOGQRWVXEVWDQWLDOO\H[WHQGEH\RQGWKHORDGLQJ
VXUIDFHRIWKHURRIUDFN5HIHUWR6W9=2RUQDWLRQ
UHJXODWLRQV
Vehicle Driving and Regulations
7KHVSHHGGULYHQPXVWEHVXLWHGWRWKHORDGWUDQVSRUWHGDQG
WRRI´FLDOVSHHGOLPLWV,QWKHDEVHQFHRIDQ\VSHHGOLPLWVZH
UHFRPPHQGDPD[LPXPVSHHGRIPSK
:KHQWUDQVSRUWLQJDQ\ORDGWKHVSHHGRIWKHYHKLFOHPXVW
WDNHLQWRDFFRXQWDOOFRQGLWLRQVVXFKDVWKHVWDWHRIWKHURDG
WKHVXUIDFHRIWKHURDGWUDI´FFRQGLWLRQVZLQGHWF9HKLFOH
KDQGOLQJFRUQHULQJEUDNLQJDQGVHQVLWLYLW\WRVLGHZLQGVZLOO
FKDQJHZLWKWKHDGGLWLRQRIURRIWRSORDGV
2IIURDGGULYLQJLVQRWUHFRPPHQGHGDQGFRXOGUHVXOWLQ
GDPDJHWR\RXUYHKLFOHRU\RXUJHDU
Maintenance
7KHDFFHVVRU\UDFNVKRXOGEHFDUHIXOO\FOHDQHGDQG
PDLQWDLQHGSDUWLFXODUO\GXULQJWKHZLQWHUPRQWKV8VHRQO\
DVROXWLRQRIZDWHUDQGVWDQGDUGFDUZDVKOLTXLGZLWKRXWDQ\
DOFRKROEOHDFKRUDPPRQLXPDGGLWLYHV
)RUUHDVRQVRIUDQJHHI´FLHQF\DQGWKHVDIHW\RIRWKHUURDG
XVHUVWKHDFFHVVRU\UDFNDQGURRIUDFNVKRXOGEHUHPRYHG
ZKHQQRWLQXVH
3HULRGLFDOO\LQVSHFWDFFHVVRU\UDFNIRUGDPDJH5HSODFH
ORVWGDPDJHGRUZRUQSDUWV8VHRQO\RULJLQDOVSDUHSDUWV
REWDLQHGIURPDVWRFNLQJVSHFLDOLVWGHDOHURUPDQXIDFWXUHU
Any changes made to the roof racks and accessory racks as
ZHOODVWKHXVHRIVSDUHSDUWVRUDFFHVVRULHVRWKHUWKDQWKRVH
VXSSOLHGE\WKHPDQXIDFWXUHUZLOOOHDGWRWKHODSVLQJRIWKH
PDQXIDFWXUHUVZDUUDQW\DQGOLDELOLW\IRUDQ\PDWHULDOGDPDJH
RUDFFLGHQWV<RXVKRXOGREVHUYHWKHVHLQVWUXFWLRQVWRWKH
OHWWHUDQGRQO\XVHWKHRULJLQDOSDUWVVXSSOLHG
EN IMPORTANT WARNINGS
08

Lock Core Removal
Lock Core Removal
09
With the cover open, insert the
control key, and then remove the
existing lock.
Unlock and open the cover to reveal
the screw holding the lock core in
place. This screw is located on the
right-hand side at the back of the
cover. Using a T10 Torx wrench, turn
the screw counterclockwise 3-4 times
to loosen it.
,QVHUWWKHµDWHGJHGFRQWURONH\LQWR
the new lock core, then use it to push
the core all the way into the housing.
While keeping the core secured with
the tip of your thumb, remove the
control key to ensure that the lock
remains within the housing.
1
2
3

Lock Core Removal (continued)
Lock Core Replacement
Tighten the screw with a torx wrench.
4
10