TESY GCV6SL 804420 B11 TSR Specification sheet
BG 2-5
EN ELECTRIC WATER HEATER 6-9
Instructions for use and maintenance
RU
10-13
ES TERMO DE AGUA ELÉCTRICO 14-17
Instrucciones de uso y mantenimiento
PT CALENTADOR DE AQUA ELÉCTRICO 18-21
Manual de instalação e uso
DE
ELEKTRISCHER WARMWASSERSPEICHER 22-25
Gebrauchsanleitung und pege
IT SCALDABAGNI ELECTTRICI 26-29
Istruzioni di uso e manutenzione
DK ELEKTRISK VANDVARMER 30-33
Monterings- og betjeningsvejledning
HUELEKTROMOS MELEGVÍZTÁROLÓ
34-37
Szerelési és kezelési útmutató
RO BOILER ELECTRIC 38-41
Instruciuni de utilizare i întreininere
PL POGRZEWACZE ELEKTRYCZNE 42-45
Instrukcja instalacji, użytkowania i obsługi
CZ ELEKTRICKÝ OHŘÍVAČ VODY 46-48
Návod k použití a údržbě
SK ELEKTRICKÝ OHRIEVAČ VODY 49-51
Návod k obsluhe a údržbe
RS ELEKTRIČNI BOJLER 52-55
Uputstvi za upotrebu i održavanje
HR ELEKTRIČNE GRIJALICE VODE 56-59
Upute za uporabu i održavanje
AL BOJLERIT ELEKTRIK 60-63
Instruksioni për shfrytězimin
UA
64-67
SI ELEKTRIČNI GRELNIK VODE 68-71
Navodila za uporabo in vzdrževanje
SE ELEKTRISK VARMVATTENBEREDARE 72-75
Monterings- och bruksanvisning
LT ELEKTRINIS VANDENS ŠILDYTUVAS 76-79
Pajogimo, naudojimo irpreti ros instrukcija
EE ELEKTRILINE VEESOOJENDAJA
80-83
Paigaldus ja kasutusjuhend
LV ELEKTRISKAIS ŪDENS SILDĪTĀJS 84-87
Lietošanas un apkopes
NOELEKTRISK VARMTVANNSBEREDER 88-91
Instruksjoner for bruk og vedlikehold
GR ΗΛΕΚΤΡΙΚO ΘΕΡΜΟΣΙΦΝΟ 92-95
Οδηγίε χρήσει και συντήρηση
MK 96-99
FR
CHAUFFEEAU ÉLECTRIQUE
100-103
Instruction d’installation et de fonctionnement
AR
104-107
www.tesy.com
is a registered trade mark of Tesy ltd.
2
BG ,
TESY . ,
.
eo
.
, ,
.
, ,
.
, ,
.
,
/ ,
.
EN 60335-1, EN
60335-2-21..
I.
, 6 bars
(0.6 MPa).
, 4°C
.
10°dH ( ). ,
„-”
,
, ..
,
2 kW.
II.
1. , -
2. -
3. -
4. -
Това не е водопроводно налягане. То е обявено за
уреда и се отнася до изискванията на стандартите
за безопасност.
5. - ,
6. - : GC--; SS-
V -
()
7. - I
8. - I
9. 40°C V40 -
I
10. - I
11. -
I
12. -
I
()
13. - II
14. - II
III.
•
.
• , .
ВИМАНИЕ!Неправилният монтаж исвързванена уредаможе даго
направиопасенза здраветои живота напотребителите, като е
възможно да нанесетежки итрайни последствиязатях, включително но не
самофизическиуврежданияи/или смърт.Товасъщоможеда доведе дощетиза
имуществотоим/уврежданеи/или унищожаване/, както инатова на трети
лица,причиненивключителноно не самоот наводняване, взрив ипожар.
Монтажът,свързванетокъм водопроводнатаи електрическата мрежа,и
въвежданетов експлоатацияследвада бъдат извършвани самоиединствено
отправоспособни електротехници и техници заремонт и монтаж на уреда,
придобили своята правоспособностна територията надържавата,на коятосе
извършват монтажъти въвеждането в експлоатация на уреда ив съответствиес
нормативнатаи уредба.
•
( ).
• 0
°
,
( .V, 2“
”).
• ( ),
.
.
3
BG
Български
IV.
, /
/ /
/, - .
1. e ()
( )
, G ½“
( ) (
).
:
• -
•
().
G ¾“.
2. .
-
.
,
.
(),
,
.
3. -
.
-
( !
),
.
Възвратно-предпазният клапан не може да защити
уреда при подавано от водопровода налягане по-високо
от обявеното за уреда. Подаването на по-високо от
обявеното в тази инструкция водопроводно налягане към
уреда може да го увреди, при което гаранцията му отпада и
производителят не носи отговорност за евентуални
причинени щети.
V.
ВИМАНИЕ!Неправилниятмонтаж и свързване науреда
можедагонаправи опасензаздравето и живота на
потребителите, катое възможнода нанесетежкии
трайнипоследствияза тях, включителнононе самофизически
уврежданияи/или смърт. Това същоможедадоведе до щетиза
имуществотоим /увреждане и/илиунищожаване/, кактои на
тована трети лица,причинени включителноно не самоот
наводняване, взрив и пожар.
Монтажът, свързванетокъм водопроводната и електрическата
мрежа,ивъвеждането в експлоатация следвадабъдат извършвани
самои единственоот правоспособниелектротехници итехници за
ремонтимонтажна уреда, придобили своята правоспособностна
териториятанадържавата, на коятосеизвършватмонтажът
ивъвежданетов експлоатация на уреда и в съответствие с
нормативнатаиуредба.
1.
ВАЖНО:
Инсталирането на уреда е за сметка на купувача
.
,
.2 V
• (
). .
.
• , -
/ /,
.
.
Забраняват се всякакви промени и преустройства в конструкцията и
електрическата схема на бойлера. При констатиране на такива
гаранцията за уреда отпада. Като промени и преустройства се разбира
всяко премахване на вложени от производителя елементи, вграждане на
допълнителни компоненти в бойлера, замяна на елементи с аналогични
неодобрени от производителя.
• .
• ( )
.
• 8 8
, ,
, a
•
•
.
4
BG
,
.
,
-.
- aa a
a . (min. Ø 10
mm) (
). ,
220 310 - . 1a.
2 . 1.
.
2 .1b.
За избягване причиняването на вреди на потребителя и на
трети лица в случаи на неизправност в системата за
снабдяване с топла вода е необходимо уреда да се монтира
в помещения имащи подова хидроизолация и дренаж в
канализацията. В никакъв случаи не слагайте под уреда предмети,
които не са водоустойчиви. При монтиране на уреда в помещения
без подова хидроизолация е необходимо да се направи защитна
вана под него с дренаж към канализацията.
Забележка: защитната вана не влиза в комплекта и се
избира/закупува от потребителя.
, -.
2.
.3: a - ; b - ; -
: 1- ; 2 – ; 3-
( 0.6 MPa); 4- ;
5 – ; 6-; 7 –
//
: - // , - /
/ .
-
, .
, ,
.
: ()
( EN 1487
EN 1489), .
EN 1487
0.7 MPa. ,
0.1 MPa
.
.
Не се допуска друга спирателна арматура между
възвратно-предпазния клапан (предпазното
устройство) и уреда.
Наличието на други (стари) възвратно-предпазни
клапани може да доведе до повреда на вашия уред и те
трябва да се премахнат.
Неседопусканавиването наклапанакъм резбис дължинанад
10мм.,в противен случайтоваможедадоведе до повредата
навашияклапан, което е опасно за вашия уред.
При бойлерите за вертикален монтаж предпазният
клапан трябва да бъде свързан към входящата тръба
при свален пластмасов панел на уреда.
Възвратно-предпазният клапан и тръбопровода от него
към бойлера трябва да бъдат защитени от замръзване.
При дрениране с маркуч – свободният му край трябва
винаги да е отворен към атмосферата (да не е потопен).
Маркуча също трябва да е осигурен срещу замръзване.
,
.
. ,
.
.
.
.
. 7 (. 3 3b)
.
, , :
• –
• -
,
.
При източване трябва да се вземат мерки за
предотвратяване на щети от изтичащата вода.
,
I -,
,
.
.
3. .
Преди да включите електрическото захранване,
уверете се че уреда е пълен с вода.
3.1.
, .
,
.
Контакт трябва да бъде правилно свързан към
отделен токов кръг осигурен с предпазител. Той
трябва да бъде заземен.
3.2.
,
16 (20A >
3700W). –
.
,
III.
:
• –
(L)
• –
(N)
• - –
( )
3.3. , .
,
16 (20A >
3700W). ()
- 3 x 2,5 mm2 3000W ( 3
x 4.0 mm2 > 3700W).
III.
, :
• A 1 L L1
• N (B B1 N1)
•
, .
, !
Пояснение към фиг.2:
TS – термоизключвател; TR – терморегулатор; S – ключ (при
моделите с такъв); R – нагревател; IL – сигнална лампа; F – фланец;
KL – лустър клема
5
BG
Български
VI.
.
, ,
.
,
.
!
VII. .
1. .
,
.
3.2
V (
).
2.
. 2 :
1 - ( )
2 -
3 - (
)
2.1.
.
.
.
•
. , ,
(.1 -).
( .2.2)
• ,
. , ,
.
2.2. ()
–
–
, :
• ,
• ,
• – .3 -
2.3. –
()
,
.
.
Веднъж месечно поставяйте ръкохватката на позиция
за максимална температура, за период от едно
денонощие (освен ако уреда работи постоянно в този
режим) - виж Приложение I (11) Максимална температура на
термостата. Така се осигурява по-висока хигиена на загряваната
вода.
ВАЖНО: При модели, които нямат ръкохватка за
управление на термостата, настройката за
автоматично регулиране на температурата на
водата е фабрично зададена зададена - виж Приложение I (12)
Фабрично зададени температурни настройки.
Режим против замръзване (фиг.2). При тази настройка
уреда поддържа температура която не позволява водата
в него да замръзне. Електрическото захранване на уреда
трябва да бъде включено. Предпазния клапан и тръбопровода от
него към уреда задължително трябва да са осигурени срещу
замръзване
e –
60°.
.
3. ( ).
()
,
,
.
Следзадействане товаустройство несе самовъзстановяваи
уредът нямада работи.Обърнете секъм оторизирансервиз за
отстраняванена проблема.
VIII.
- 80°C.
,
(:
).
:
1. () -
2.
, -
().
.
:
- ,
,
. ,
.1d ÷ .1f.
(. 5):
[m²] - S;
[l] - V;
[MPa] - P;
[°C] - Tmax.
.
()
,
.
.
½”
- „TS”.
,
.
Задължително е да бъдат използвани диелектрични
втулки при свързване на топлообменника към инсталация
с медни тръби.
Заограничаване накорозията, винсталациятатрябва да
бъдат използванитръбис ограниченадифузия нагазове.
IX.
,
/.. /.
.
. /
/. -.
“” .
, .
( ),
.
.
.
,
.
!
( ).
6Instructions for use and maintenance
EN Dear Clients,
The TESY team would like to congratulate you on your new purchase.We
hope that your new appliance shall bring more comfort to your home.
This technical description and instructions manual was prepared in
order to acquaint you with the product and the conditions of proper
installation and use. These instructions were also intended for use
by qualied technicians, who shall perform the initial installation, or
disassembly and repairs in the event of a breakdown.
The observance of the instructions contained herein is in the interest
of the buyer and represents one of the warranty conditions, outlined in
the warranty card.
Please consider that following the current instructions will primarily
be of interest to the consumer, but along with this, it is also one of
the warranty conditions, pointed out in the warranty card, so that the
consumer can benet from the free warranty services. The producer
is not responsible for damages in the appliance that have appeared
as a result of operation and/or installation not corresponding to the
instructions here.
The electric water heater complies with the requirements of EN 60335-1,
EN 60335-2-21.
I. INTENDED USE
The appliance is intended to supply hot water to household sites
equipped with a piping system working at pressure below 6 bar (0,6
Mpa).
It is designed to operate only in closed and heated premises where the
temperature is not lower than 4°C and it is not designed to operate in a
continuous protracted regime.
The appliance is designed to operate in regions where the water
hardness is not more than 10°dH. In case that it is installed in a region
where the water is harder it is possible that limestone precipitation
accumulate very fast. This can cause a specic noise during heating,
as well as fast damaging of the electrical part. For regions with harder
water yearly cleaning of the limestone precipitation in the appliance
is recommended, as well as usage of not more than 2 kW of heating
power.
II. TECHNICAL PARAMETERS
1. Nominal volume V, liters - see the appliance’s rating plate
2. Nominal voltage - see the appliance’s rating plate
3. Nominal power consumption - see the appliance’s rating plate
4. Nominal pressure - see the appliance’s rating plate
This is not the water mains pressure. This is the pressure
that is announced for the appliance and refers to the
requirements of the safety standards.
5. Water heater type - closed type accumulating water heater, with
thermal insulation
6. Inner coating - for models: GC-glass-ceramics; SS-stainless steel;
EV - email
For models without heat exchanger (coil)
7. Daily energy consumption – see Annex I
8. Rated load prole - see Annex I
9. Quantity of mixed water at 40°C V40 litres - see Annex I
10. Maximum temperature of the thermostat - see Annex I
11. Default temperature settings - see Annex I
12. Energy eciency during water heating - see Annex I
For models with heat exchanger (coil)
13. Storage volume in litres - see Annex II
14. Standing loss - see Annex II
III. IMPORTANT RULES
• The water heater must only be mounted in premises with normal re resistance.
• Do not switch on the water heater unless you established it was lled with water.
Attention! Improper installation and connection of the appliance may make
it hazardous for the health and life of consumers. It may cause grievous and
permanent consequences, including but not limited to physical injuries and/or
death. Improper installation and connection of the appliance may also lead to
damage to the consumers’ property /damage and/ or destruction/, or to that of
third persons, as a result of, but not limited to ooding, explosion and/or re.
Installation, connection to the main water and power supply, and putting into
operation must be carried out by certied electricians and technical personnel certied
in installation of this category of appliances, who have obtained their license in the
state where the installation and commissioning of the appliance are carried out, and in
compliance with its local legislation.
• Upon connecting the water heater to the electric mains care must be taken to
connect the safety lead.
• If the probability exists for the premise’s temperature to fall below 0°, the water
heater must be drained (observe the procedure outlined in section V, subsection 2
‘’Water heater’s piping connection”).
• During operation – regime of heating the water – water drops through the
drainage opening of the protection valve are usual.
• The protection valve should be left open to the atmosphere. Measures should be
taken to lead and collect the leakages in order to prevent damages, ensuring that this
is in conformation with the requirements described in p. 2 in paragraph V.
Instructions for use and maintenance 7
EN
English
IV. DESCRIPTION AND PRINCIPLE OF WORK
The appliance consists of a body, ange at the bottom side /for water
heaters intended for vertical mounting/ or at the sides /for water
heaters intended for horizontal mounting/, protective plastic panel
safety-return valve.
1. The body consists of a steel reservoir (water tank) and housing
(outer shell) with thermal insulation placed in-between made of
ecologically clean high density polyurethane foam, and two pipes with
thread G ½‘’for cold water supply (marked by a blue ring) and hot
water outlet pipe (marked by a red ring).
The inner tank may be of two types depending on the model:
• Made of steel protected form corrosion by a special glass-ceramics
coating
• Made of stainless steel
The vertical water heaters may be outtted with a built in heat
exchange unit (serpentine tube). The heat exchenger’s entrance and
exit are located at the sides and represent pipes with thread G ¾‘’.
2. The ange is outtted with: electric heater and thermostat.
The water heaters with glass-ceramics coating are outtted with a
magnesium protector.
The electric heater is used for heating the water in the tank and is
managed by the thermostat, which automatically maintains the set
temperature.
The thermostat has a built in overheating safety device, which switches
of power to the heater when the water temperature reaches excessive
values.
3. The safety-return valve prevents the appliance’s complete
emptying in the event the cold water supply is interrupted. The
valve protects the appliance from pressure increases higher than the
allowed value during heating (! pressure increases upon an increase
of temperature), via release of excess pressure during the drainage
opening.
The safety-return valve cannot protect the appliance in the
event of water mains pressure in excess of the acceptable
pressure stated for the appliance.
V. MOUNTING AND SWITCHING ON
Attention! Improper installation and connection of the
appliance may make it hazardous for the health and life
of consumers. It may cause grievous and permanent
consequences, including but not limited to physical injuries and/
or death. Improper installation and connection of the appliance
may also lead to damage to the consumers’ property /damage
and/ or destruction/, or to that of third persons, as a result of, but
not limited to ooding, explosion and/or re.
Installation, connection to the main water and power supply, and
putting into operation must be carried out by certied electricians
and technical personnel certied in installation of this category of
appliances, who have obtained their license in the state where the
installation and commissioning of the appliance are carried out, and in
compliance with its local legislation.
Notice:
The installation of the unit is at the buyer’s expense
.
• The valve and the elements linked to it must be protected from freezing.
• During the heating the appliance could produce a hissing noise (the boiling water).
This is common and does not indicate any damage. The noise gets higher with the
time and the reason for this is the accumulation of limestone. To remove the noise
the appliance must be cleaned from limestone. This type of cleaning is not covered
by the warranty.
• In order to secure the water heater’s safe operation, the safety return-valve must
undergo regular cleaning and inspections for normal functioning /the valve must
not be obstructed/, and for the regions with highly calcareous water it must be
cleaned from the accumulated lime scale. This service is not provided under warranty
maintenance.
All alterations and modications to the water heater’s construction and electrical
circuitry are forbidden. If such alterations or modications are established during
inspection, the appliance’s warranty shall be null and void. Alterations and
modications shall mean each instances of removal of elements incorporated by the
manufacturer, building in of additional components into the water heater, replacement
of elements by similar elements unapproved by the manufacturer.
• These instructions shall also apply to water heaters equipped with a heat
exchanger.
• If the power supply cord (of models that have one) is damaged, it must be replaced
by a service representative or a person with similar qualication, to avoid any risk.
• This appliance can be used by children aged from 8 years and above and persons
with reduced physical, sensory or mental capabilities or lack of experience and
knowledge if they have been given supervision or instruction concerning use of the
appliance in a safe way and understand the hazards involved.
• Children shall not play with the appliance.
• Cleaning and user maintenance shall not be made by children without supervision.
8Instructions for use and maintenance
EN 1. Mounting
We recommend the mounting of the device at close proximity to
locations where hot water is used, in order to reduce heat losses during
transportation. In the event the device is mounted in a bathroom, the
selected location must exclude the possibility of water spray contact
from the showerhead or portable showerhead attachment.
The appliance is axed to a wall via the mounting brackets attached to
the unit’s body (if the brackets are not attached to the unit’s body, they
must be axed in place via the provided bolts). Two hooks are used
for suspending the appliance (min. Ø 10 mm) set rmly in the wall (not
included in the mounting set). The mounting bracket’s construction
designed for water heaters intended for vertical mounting is universal
and allows a distance between the hooks of 220 to 310 mm (g. 1a). For
water heaters intended for horizontal mounting, the distances between
the hooks vary for the dierent models and are specied in the table
2 to Fig. 1c. For water heaters intended for oor installation - table 2
to Fig. 1b.
In order to prevent injury to user and third persons in the
event of faults in the system for providing hot water, the
appliance must be mounted in premises outtted with oor hydro
insulation and plumbing drainage. Don’t place objects, which are
not waterproof under the appliance under any circumstances. In
the event of mounting the appliance in premises not outtted
with oor hydro insulation, a protective tub with a plumbing
drainage must be placed under the appliance.
Notice: the set does not include a protective tub and the user must
select the same.
2. Water heater connection to the pipe network.
Fig. 3: a) - for vertical; b) - for horizontal installation; c) - for oor
installation
Where: 1 - Inlet pipe; 2 - Safety valve; 3 - reducing valve (for water main
pressure > 0,6 MPa); 4 - Stop valve; 5 - Funnel connected to the sewer
network; 6 – Hose; 7 - Drain water tap.
Upon connecting the water heater to the water mains you must consider
the indicative color markings /rings/ axed to the pipes: blue for cold /
incoming/ water, red for hot /outgoing/ water.
The mounting of the safety return-valve supplied with the water heater
is obligatory.The safety return-valve must be mounted on the cold water
supply pipe, in observance of the direction arrow stamped on its body,
indicating the incoming water’s direction. Additional stopcocks must not
be mounted between the safety return-valve and the water heater.
Exception: If the local regulations (norms) require the usage of another
protection valve or mechanism (in accordance with EN 1487 or EN
1489), then it must be bought additionally. For mechanisms operating in
accordance with EN 1487 the announced operational pressure must be
no more than 0.7 MPa. For other protection valves, the pressure at which
they are calibrated must be 0.1 MPa lower than the one marked on the
appliance’s sign. In these cases the safety valve which the appliance is
supplied with should not be used.
The presence of other /old/ safety return-valves may lead to a
breakdown of your appliance and they must be removed.
Other type of stopping armature is not allowed between the
protection return valve (the protective device) and the appliance.
The attaching of the safety return-valve to threads longer than
10 mm is not allowed, otherwise this may damage the valve
and poses danger for your appliance.
With appliances for vertical assembly, the safety valve has to
be connected to the ingoing pipe with the safety plastic panel
of the appliance being taken o.
The safety valve and the pipe between the valve and the water
heater must be protected from freezing. During hose draining
- its free end must be always open to the atmosphere (not to be
immersed). Make sure that the hose is also protected from freezing.
Opening the cold-water stopcock of the water supply piping network
and opening the hot-water stopcock of the water-mixing faucet
carries out the lling of the water heater with water. After the lling
is complete, a constant stream of water must begin to ow from the
water-mixing faucet. Now you can close the hot water stopcock.
In the event you must empty the water heater, rst you must cut o
its power supply. The inow of water from the water mains must rst
be terminated and the hot water tap of the mixing-faucet must be
opened. The water tap 7 (g 3a and 3b) must be opened to drain the
water from water tank. If there is no such tap build in the pipe line, than
the water can be drain as follow:
• Models equipped with safety valve with lever -You can drain the
water from the water heater by lifting the safety return-valve’s lever.
Water will drain from the safety return-valve’s drainage opening
• Models equipped with safety valve without lever - water can be
drain directly from inlet pipe of water tank after when you disconnect
it from water main
In the event of removing the ange, the discharge of several liters of
water, which remain in the water tank, is normal.
Measures must be undertaken to prevent damage from
discharging water during draining.
In case that the pressure in the water mains is over the value
pointed out in the above paragraph I, then it is necessary to
assemble a pressure reduce valve, otherwise the water heater
would not function properly. The Manufacturer does not assume
any liability for problems arising out of the appliance’s improper
use.
3. Water heater connection to the electrical network
Make sure the appliance is full of water prior to switching on
the electrical mains power.
3.1. Models with power cord with a plug are connected by
inserting the plug into a contact. They are switched o the power
supply by drawing the plug out of the contact.
The wall-plug must be properly connected to a separate electrical
circle that is provided with a protector. It must be earthed.
3.2. The appliance has to be connected to a separate electricity
circuit of the stationary electrical wiring. The connecting has to be
constant- with no plug contacts.The circuit has to be supplied with
a safety fuse (16A) and with inbuilt device to ensure disconnection
of all pole pieces in the conditions of over-voltage from category III.
The connecting of the conductors of the supply cord of the
appliance has to be carried out as follows:
• conductor with brown insulation – to the phase conductor of
the electrical wiring (L)
• conductor with blue insulation- to the neutral conductor of the
wiring (N)
• conductor with yellow-green insulation – to the safety
conductor of the wiring ( )
3.3. Models without power cord
The appliance has to be connected to a separate electricity circuit of
the stationary electrical wiring. The circuit has to be supplied with a
safety fuse 16A (20A for power > 3700W). Copper single core (rigid
– non stranded) conductor shall be used for the connection – cable
3 x 2.5 mm² (cable 3 x 2.5 mm² for power > 3700W).
The electrical circuit supplying the appliance must have an in-built
device ensuring the splitting of all terminal poles under conditions
of super-voltage of category III.
To install the power supply wire to the appliances remove the
plastic cover.
Connect the power wires in compliance with the marks on the
terminals, as follows:
• the phase - to mark A, A1, L or L1;
• the neutral - to N (B or B1 or N1)
• The safety wire must be obligatory connected to the screw joint
marked with .
After the installation, put the plastic cover back in its place!
Explanations to Fig. 2:
TS - thermal switch; TR - thermal regulator; S - switch (for models that
have one); R - heater; IL - light indicator; F - ange; KL - luster terminal;
Instructions for use and maintenance 9
EN
English
VI. RUST PROTECTION MAGNESIUM ANODE FORWATER
HEATERS WITHWATER TANKS COVERED BY GLASSCERAMICS
COATING
The magnesium anode protects the water tank’s inner surface from
corrosion.
The anode element is an element undergoing wear and tear and is
subject to periodic replacement.
In view of the long-term and accident free use of your water heater, the
manufacturer recommends periodic inspections of the magnesium
anode’s condition by a qualied technician and replacement whenever
required, and this could be performed during the appliance’s technical
preventive maintenance.
For replacements, please contact the authorized service stations!
VII. OPERATION
1. Switch on:
Before switching on the appliance for rst time, make sure that the
water heater is properly connected to the power supply network and
full with water.
The appliance is switched on by a switch integrated into the
installation, described in item 3.2 of Section V, or upon connecting the
plug to the electrical contact (in the case of an extension cable with
plug).
2. Water heaters with electromechanical control
Fig. 2 where:
1 - Electrical switch button (for models with switch)
2 - Light indicators
3 - Thermostat control knob (only for models with adjustable
thermostat)
2.1. Models with built-in switch
There is an embossed marking on the button of the electrical switch .
• Push and release the button in order to switch on the electrical
switch. If it lightens, this means that it is switched on.The button lights
constantly unless the switch is switched o or the appliance power
supply from electrical main is switched o (see item 1 above). The light
indicators lighten too (see item 2.2. below).
• In order to switch o the electrical switch, push and release
the button again. It must stop to light if it is switched o. The light
indicators stop lighting too.
2.2. Light indicators
The indicators light in red color – means that the appliance is in heating
mode
The indicators light in blue color – means that water is warmed and the
thermostat is switched o, because the set temperature is reached
The light indicators do not light when:
• The electrical switch of the appliance is switched o
• The appliance power supply from electrical main is switched o
• Protection according to the temperature is switched o – see item
3 below
2.3. Temperature setup (for models with adjustable thermostat)
This setup allows the gradual setting of the desired temperature,
achieved by using a handle on the control panel. Turn the knob to the
upward indication, in order to increase the temperature of the hot
water.
Place the thermostat knob in position for maximum
temperature (unless it is on this position constantly), for period
of one day each month - see Annex I (11) Maximum temperature of the
thermostat. This ensures higher hygiene of the used hot water.
IMPORTANT: Models that do not have thermostat control
knobs have automatic water temperature preset by the
manufacturer - see Annex I (12) Default temperature settings.
ANTI-FREEZE MODE (g.2). With this setup the device
maintains temperature that does not allow the water freeze in
it. The electrical supply of the appliance should be turned on and so
must be the appliance. The safety valve and the pipe between the valve
and the appliance must be protected from freezing. In case that for
some reason the electrical supply is cut o, there is a risk of freezing of
the water in the water tank. For this reason we recommend draining the
water out of the appliance before long absences (longer than a week).
Position e(Energy-save mode) – At this mode, water temperature
reaches up to approximately 60°. Heat losses are reduced in this way.
3. Protection according to the temperature (valid for all models).
The appliance is equipped with a special facility (thermal circuit-
breaker) for protection against over-heating of the water, which
is switching o the heater from the electricity network, when the
temperature reaches too high values.
When this device operates, it does not self-reset and the
appliance will not work. Please call an authorized service for
solving the problem.
VIII. MODELS EQUIPPEDWITH A HEAT EXCHANGER SERPENTINETUBE.
These are appliances with inbuilt heat exchanger and are intended to
be connected to the heating system with maximum temperature of the
heat carrier of 80°C.
The control over the ow through the heat exchanger is a matter of
solution for the particular installation, whereby the choice should
be made at its design (e.g. external thermostat that measures the
temperature in the water tank and operates a circulation pump or a
magnet valve).
Water heaters with a heat exchanger provide the opportunity for the
water to be heated in two ways:
1. by means of a heat exchanger (coil) – a primary way of heating the water,
2. by means of an auxiliary electrical heating element with automatic
operation, built in the appliance – it is used only when additional
heating of the water is needed or in case of repairs to the system of the
heat exchanger (coil).The proper way of connecting the appliance to
the electric network and how to work with it has been specied in the
previous paragraphs.
Mounting:
In addition to the mounting manner outlined above, especially for
the latter models, it shall be required to connect the heat exchanger
to the heating installation. The connections are to be carried out in
observance of the direction indicated by the arrows on Fig. 1d÷Fig. 1f.
Technical parameters (table 5):
Surface of serpentine [m²] - S;
Volume of serpentine [l] - V;
Operational pressure of serpentine [MPa] - P;
Maximum temperature of heat carrier [°C] - Tmax.
We recommend you mount stopcocks at the heat exchanger’s entry
and exit points. By stopping the ow of the thermophore via the lower
(stopcock) you shall avoid the unnecessary circulation of the thermophore
during periods of use only of the electric heating element.
Upon disassembly of you water heater equipped with a heat exchanger
you must close both stopcocks.
There is a connexion with internal thread of ½”welded to the water
tank for the purposes of installing thermal probe – marked with„TS”.
The appliance is tted with brass pocket for a thermal probe which
should be screwed into the aforesaid connexion.
The usage of dielectric bushings for connecting the heat
exchanger to an installation of copper pipes is obligatory.
For ensuring minimal corrosion, pipes with a limited diusion
of gasses must be used in the installation.
IX. PERIODIC MAINTENANCE
Under normal use of the heater, under the inuence of high temperature,
lime scale /the so-called lime scale layer/ is deposited upon the heating
element’s surface. This worsens the heat exchange between the heating
element and water. The heating element’s surface temperature increases
along /of boiling water/. The thermoregulator begins to switch on and
o more frequently. A ‘’deceptive”activation of the thermal protection is
possible. Due to these facts, the manufacturer recommends preventive
maintenance of your water heater every two years by an authorized service
center or service base. This protective maintenance must include cleaning
and inspection of the anode protector (for water heaters with glass-ceramic
coating), which shall be replace with a new one if need arises.
In order to clean the appliances use a damp cloth. Do not clean with abrasive
or solvent content detergents. Do not pour water over the appliance.
The manufacturer does not bare the responsibility for all
consequences caused by not obeying the instructions, given hereby.
Instructions for protecting the environment
Old electric appliances contain precious materials and thus
should not be thrown together with the household litter. We
kindly ask you make your active contribution for protecting the
resources and the environment by handing over the appliance in
the authorized buy-back stations (if such exist).
10
RU ,
TESY .
, .
.
,
,
.
, ,
.
, ,
,
, ,
.
,
/ ,
.
EN 60335-1, EN
60335-2-21.
I.
,
6 . (0,6 Mpa).
,
4°C .
10°dH. „ ”,
,
,
.
, 2 kW.
II.
1. V, .
2. - .
3. - .
4. - .
Это не давление водопроводной сетью. Оно
относится к прибору и соблюдает требования
стандартов безопасности.
5. - ,
6. , : GC - ; SS -
; V -
()
()
7. – . I
8. - . I
9. 40 °C V40 – .
I
10. – . I
11. – . I
12. – .
I
()
13. – . II
14. – . II
III.
•
.
• , .
ВНИМАНИЕ! Неправильная установка и подключение прибора могут
сделать его опасным для здоровья и жизни потребителей, а также
может причинить серьезные и долговечные последствия для них, в том
числе, но не только, к физическим повреждениям и/или смерти. Это также
может привести к ущербам их имущества /повреждению и/или
уничтожению/, а также таким третьих лиц, вызванным включительно,
но не только, наводнением, взрывом, пожаром.
Монтаж, подключение к водопроводу и к электрической сети должны
выполняться правоспособными электротехниками и техниками по ремонту и
монтажу приборов, которые получили свою правоспособность на территории
страны, в которой осуществляется монтаж и ввод в эксплуатацию прибора и
в соответствии с нормами ее законодательства.
•
.
• , 0
°
,
e (
. V, 2“ ”).
• – ( ) –
. .
,
, .2 V.
11Русский
RU
IV.
, /
/ /
/,
- .
1. ( )
( ) ,
,
G ½‚‘ ( )
( ).
:
• ,
•
().
G ¾‚‘.
2. ..
.
,
.
(),
,
.
3. -
.
,
(!
) .
Возвратно-предохранительный клапан не может
защитить устройство в случае водопроводной подачи
под давлением, превышающим объявленное давление устройства.
V.
ВНИМАНИЕ! Неправильная установка и подключение
прибора могут сделать его опасным для здоровья и
жизни потребителей, а также может причинить
серьезные и долговечные последствия для них, в том числе,
но не только, к физическим повреждениям и/или смерти.
Это также может привести к ущербам их имущества /
повреждению и/или уничтожению/, а также таким третьих
лиц, вызванным включительно, но не только, наводнением,
взрывом, пожаром.
Монтаж, подключение к водопроводу и к электрической сети
должны выполняться правоспособными электротехниками и
техниками по ремонту и монтажу приборов, которые получили
свою правоспособность на территории страны, в которой
осуществляется монтаж и ввод в эксплуатацию прибора и в
соответствии с нормами ее законодательства.
Примечание: У
становка прибора ест за счет покупателя
.
.
• ( ).
.
- . ,
. .
•
( ) - ,
.
.
Любые изменения и переустройства в конструкции и электрической
схеме бойлера запрещены. При их констатации гарантия теряет свое
действие. Под изменениями и переустройством подразумевается любое
удаление заводских элементов, установка в бойлере дополнительных
компонентов, замена элементов аналогичными, но не одобренными
производителем.
• .
• ( , ) ,
.
• 8- 8-
,
, ,
a
,
.
•
• ,
.
12
RU 1. .
,
.
,
.
( ,
).
(min. Ø 10 mm),
( ).
,
220 300 (.1).
,
2 (. 1c).
В целях безопасности потребителя и третьих
лиц в случае неполадок в системе подачи горячей
воды необходимо устанавливать бойлер в
помещениях, имеющих напольную гидроизоляцию и
канализационный дренаж. Запрещается устанавливать
бойлер на неводоустойчивые предметы. При монтаже
устройства в помещениях без напольной гидроизоляции
необходимо под бойлером установить защитную ванну с
канализационным дренажом.
Примечание: защитная ванна не входит в комплект и
обеспечивается потребителем.
2. .
. 3a – ; . 3b-
. 3c –
: 1 - ; 2 - ; 3 -
(
0,7 MPa); 4 - ; 5 -
; 6 – ; 7 –
- : - /
/ , // .
- ,
, .
,
, .
.
: ()
( EN 1487 EN 1489),
. , EN 1487
0.7
MPa. ,
, 0.1 MPa
.
, .
Наличие других /старых/ возвратно-
предохранительных клапанов может привести к
повреждению бойлера, вот почему они должны быть удалены.
Не допускается никакой другой запорной арматуры
между возвратно предохранительным клапаном
(предохранительным устройством) и прибором.
Не допускается закручивание клапана к резьбе длиной
более 10 мм, иначе это может привести к повреждению
клапана и выходу бойлера из строя.
Возвратно предохранительный клапан и трубопровод
от него к водонагревателю должны быть
защищенными от замораживания. При дренированием
с шлангом – его свободный конец должен всегда быть
открытым к атмосфере (Не погруженный). Шланг тоже должен
быть обеспечен против замораживания.
.
,
.
, ,
.
.
. 7 (. 3 3b) ,
. ,
:
•
–
;
•
-
,
.
,
.
При сливе воды необходимо предпринять меры по
предотвращению ущерба от вытекающей воды.
,
I ,
,
.
,
.
3.
Перед подачей электрического питания необходимо
убедится, что бойлер наполнен водой.
3.1. ,
.
.
Контакт должен быть правильно подключен к
отдельной цепи, которая обеспечена предохранителем.
Он должен быть заземлен.
3.2.
16 (20A >
3700W). –
.
,
III.
:
• –
(L)
• –
(N)
• - –
( )
3.3.
16 (20A >
3700W). )
, ( 3x2,5 mm² 3000W
( 3x4.0 mm² > 3700W).
,
III.
.
, :
• A 1 L L1
• N (B B1 N1)
• ,
.
, !
Пояснение к фиг.2:
TS – термовыключатель; TR – терморегулятор; S – ключ (при
моделях с таковым); R – нагреватель; IL – сигнальная лампа; F –
фланец; KL – лустер клемма.
13Русский
RU
VI.
.
,
.
, .
.
VII. .
1. :
,
.
,
, 3.2 V
(
).
2. .
.2 :
1- (
);
2- ;
3- (
)
2.1.
.
. .
•
. , ,
(.1 ).
( .2.2)
•
. , ,
. .
2.2. ()
–
–
, :
• ,
•
• – .3
2.3. –
()
,
- . I (11)
.
.
Раз в месяц надо ставить ручки в позицию для
максимальной температуры, за сутки (если прибор не
работает постоянно в этом режиме). Это
обеспечивает лучшую гигиену нагреваемой воды.
ВАЖНО: При моделей, без ручек для управления
термостата, настройка автоматического
регулирования температуры воды устанавливается на
заводе - см. Приложение I (12) Заводские настройки
температуры.
Режим против замерзания (fig.2). При этой настройке
устройство поддерживает температуру, которая не
позволяет замерзание воды в нем. Электрическое
питание прибора должно быть включено и прибор должен быть
включен. Предохранительный клапан и трубопровод от него к
прибору обязательно должны быть обеспечены против
замораживания.
В случае, когда по какой-нибудь причине необходимо прервать эл.
питание, существует опасность вода в резервуаре замерзнуть.
Поэтому рекомендуем во время длительного отсутствия
(больше недели) слить воду из водонагревателя.
e( ) –
60°.
.
3. ( ).
() ,
,
После активации, это устройство не самовосстанавли-
вается и прибор не будет работать. Обратитесь к
оторизированному сервису для устранения проблемы.
VIII.
().
.
- 80°C.
:
1.
2. ()
3. -
:
,
,
.
(.1d÷.1f. ).
( 5):
[m²] - S;
[l] - V;
[MPa] - P;
[°C] - Tmax.
.
()
,
.
.
K ½”
- “TS”.
,
.
Обязательно надо использовать диэлектрические
лайнеры при связыванием теплообменника к
инсталяции с с медными трубами.
Для ограничивания коррозии, в инсталяции надо
использовать трубы с ограниченной диффузией газов.
IX.
,
,
. .
. /
/. .
‚‘” .
, .
. .
.
!
.
14 Instrucciones de uso y mantenimiento
ES Estimados clientes,
El equipo de TESY cordialmente le felicita su nueva compra. Esperamos
que el nuevo aparato aporte confort a su hogar.
La descripción técnica e instrucciones de funcionamiento tienen como
objetivo presentarle el producto y las condiciones un
montaje y funcionamiento correctos. Este manual va dirigido a los
instaladores legalmente acreditados que llevarán a cabo el montaje y,
posteriormente, el desmontaje y posible sustitución del equipo en caso
de deterioro o desgaste. El cumplimiento de estas instrucciones es en
benecio del usuario y comprador del equipo, así como una condición
indispensable para la aplicación de la garantía.
El fabricante no se hace responsable de los daños en el aparato y los
daños causados por el uso o ensamblaje no conforme a las indicaciones
e instrucciones de este manual. El termo eléctrico responde a los
requerimientos de EN 60335-1, EN 60335-2-21.
I. FINALIDAD
El aparato tiene como n suministrar agua caliente sanitaria a nivel
doméstico en aquellas casas con un sistema de tuberias con una
presión de no más de 6 bar (0,6 MPa).
Está diseñado para funcionar en lugares cerrados y acondicionados
en los que la temperatura no descienda por debajo de 4 ˚C y no está
diseñado para funcionar de forma continua.
El termo está fabricado para funcionar en regiones con una dureza
del agua de hasta 10 °dH. En caso de ser instalado en una zona con
agua más dura, es posible que la acumulación de depósitos de cal
se produzca a mayor velocidad. Esto puede causar ruidos durante el
calentamiento, así como un rápido deterioro de la resistencia eléctrica.
En las regiones con agua dura se recomienda limpiar el termo y
eliminar los depósitos de cal de forma anual, así como no usar una
potencia superior a los 2kW en la resistencia.
II. CARACTERÍSTICAS TÉCNICAS
1. Capacidad nominal, litros – ver la placa de características del
aparato.
2. Tensión nominal - ver la placa de características del aparato.
3. Consumo de energía nominal - ver la placa de características del
aparato
4. Presión nominal - ver la placa de características del aparato
Ésta no es la presión de la red de suministro de agua. Es la
anunciada para el aparato y se reere a los requisitos de las
normas de seguridad.
5. Tipo de termo - termo cerrado de acumulación con aislamiento
térmico
6. Recubrimiento interno – para modelos: GC-vitrocerámico; SS-acero
inoxidable, EV esmalte
Para los modelos sin intercambiador de calor (serpentín)
7. Consumo diario de electricidad - ver Anexo I
8. Perl de carga nominal - ver Anexo I
9. Cantidad de agua mezclada a 40 ° C V40 en litros - ver Anexo I
10. Temperatura máxima del termostato - ver Anexo I
11. Ajustes de temperatura de serie - ver Anexo I
12. Eciencia energética durante el calentamiento del agua - ver Anexo I
Para los modelos con intercambiador de calor (serpentín)
13. Volumen de almacenamiento en litros - ver Anexo II
14. Pérdidas de calor en carga cero- ver Anexo II
III. NORMAS IMPORTANTES
• El termo debe montarse solamente en recintos con una seguridad anti incendios normal.
• No conecte el termo sin estar seguro de que esta lleno de agua.
¡OJO! La instalación y conexión incorrecta del equipo podrán hacerlo peligroso
para la salud y la vida de los usuarios haciendo posibles los daños graves y
perdurables, incluso pero no limitados a la discapacidad física y/o muerte. También
pueden causar daños/destrucción y/o aniqulación de su propiedad, así como a la de
terceros, por inundación, explosión, incendio y otros.
La instalación, la conexión a la red de agua y a la red eléctrica, así como la puesta en
marcha deberán ser llevadas a cabo únicamente por electricistas y técnicos cualicados
para la reparación y el montaje del equipo que han adquirido sus competencias
profesionales en el territorio del país donde se lleva a cabo el montaje y la puesta en
marcha del equipo y en conformidad con su normativa.
• Durante la conexion del termo a la corriente electrica hay que tener especial
cuidado al conectar el cable de seguridad.
• Si se preve que se van a alcanzar temperaturas de congelación
(bajo °) el termo debe ser completamente vaciado (siguiendo las instrucciones en
punto V-2“Conexion hidraulica del termo”).
• Durante el funcionamiento - fase de calentamiento del agua – es habitual que
gotee agua a traves de la abertura de drenaje de la válvula de seguridad.
• La válvula de seguridad debe estar abierta a la atmósfera. Además, deben tomarse
medidas para conducir y recoger las fugas a n de evitar danos, asegurandose de que
esten en conformidad con los requisitos descritos en el punto 2 del parrafo V.
• La válvula y sus componentes deben ser protegidos contra procesos de
congelación.
• Durante el proceso de calentamiento, la resistencia puede emitir un ligero ruido
Español Instrucciones de uso y mantenimiento 15
ES
IV. DESCRIPCIÓN Y FUNCIONAMIENTO
El aparato se compone de cuerpo, brida en la parte posterior (en
termos verticales) o en ambos lados (en termos horizontales); un panel
de proteccion de plastico y una valvula de retorno de seguridad.
1. El cuerpo se compone de un tanque de acero (contenedor de agua)
y una carcasa (envoltura externa) con aislamiento térmico entre ellos de
un poliuretano ecologico de alta densidad, y dos tubos con rosca G ½
para dar agua fria (de anillo azul) y agua caliente (de anillo rojo).
El tanque interno puede ser de dos tipos en funcion del modelo:
• De acero con una cobertura especial vitroceramica para evitar la
acumulacion de cal.
• De acero inoxidable.
Los termos verticales pueden incorporar un intercambiador de calor
(serpentin). La entrada y la salida del tubo de la caldera estan situadas a
los lados y representan tubos con rosca G ¾“.
2. La brida esta equipada con: resistencia eléctrica y termostato. Los
termos con cobertura de protección vitrocerámica incoporan también
un ánodo de magnesio.
La resistencia eléctrica sirve para calentar el agua en el tanque y es
controlada por el termostato, encargado de mantener la temperatura
congurada de forma constante.
El termostato incorpora un dispositivo de seguridad para evitar el
sobrecalentamiento, que apaga el termo cuando la temperatura del
agua ha subido a demasiados grados.
3. La válvula de retorno de seguridad protege al termo de vaciarse
por completo en caso de un corte en el suministro de agua fria. La
válvula protege al aparato de subidas de presion por encima de los
valores permitidos durante la fase de calentamiento (la presión se eleva
en cuanto se produce un incremento de la temperatura), mediante la
liberación del exceso de presión durante la apertura de drenaje.
La válvula de retorno de seguridad no puede proteger el
aparato cuando el suministro de agua viene con mayor
presión que la inidicada para el aparato.
V. MONTAJE Y CONEXIÓN
¡OJO! La instalación y conexión incorrecta del equipo
podrán hacerlo peligroso para la salud y la vida de los
usuarios haciendo posibles los daños graves y
perdurables, incluso pero no limitados a la discapacidad física
y/o muerte. También pueden causar daños/destrucción y/o
aniqulación de su propiedad, así como a la de terceros, por
inundación, explosión, incendio y otros.
La instalación, la conexión a la red de agua y a la red eléctrica, así
como la puesta en marcha deberán ser llevadas a cabo únicamente
por electricistas y técnicos cualicados para la reparación y el montaje
del equipo que han adquirido sus competencias profesionales en
el territorio del país donde se lleva a cabo el montaje y la puesta en
marcha del equipo y en conformidad con su normativa.
Observacion:
Instalar el aparato está a cargo del comprador
.
1. Montje
Se recomienda que el montaje del aparato sea lo más cerca posible de
los puntos de suministro del agua caliente para con ello minimizar las
pérdidas de calor en la conducción de agua. En caso de montar el
termo en el cuarto de baño, debe ser instalado en un lugar en el que no
pueda mojarse.
El aparato se ja a la pared mediante las placas que lleva incorporadas
(agua hirviendo), lo cual es habitual y no implica ningun problema. Sin embargo,
si el ruido va a mas con el paso del tiempo puede que la razon sea la acumulacion
de cal. Para eliminar el ruido será necesario limpiar el aparato desencrustando la cal
adherida. Este tipo de limpieza no está cubierta por la garantia.
• Para asegurar un funcionamiento correcto del termo, la válvula
de retorno de seguridad debe someterse a una limpieza periodica e inspecciones
para asegurar un funcionamiento normal/ la ausencia de obstrucciones en la
valvula/ y, en las regiones con aguas altamente mineralizadas, la eliminacion de la cal
acumulada. Este servicio no está incluido en los terminos de la garantia.
Queda terminantemente prohibido realizar modicaciones o cambios tanto en la
estructura como en el circuito eléctrico del termo. Si se detecta alguna modicación
durante la inspección del aparato, la garantía quedará anulada inmediatamente. Por
modicaciones o cambios se entienden la eliminación de piezas o componentes originales
del fabricante, la incorporación de elementos adicionales en el termo o el recambio de
piezas por otros similares que no hayan sido aprobados por el fabricante.
• Estas instrucciones deben aplicarse de igual manera a los termos con
intercambiadorde calor incorporado.
• Si el cable de alimentación (en aquellos aparatos que lo incorporen) sufre danos,
debe ser sustituido por el servicio tecnico ocial o por un profesional con la
formacion adecuada para ello, a n de evitar cualquier riesgo.
• Este aparato puede ser manejado por niños mayores de 8 años, por personas con
minusvalias sicas, sensoriales o mentales, o por personas que no hayan utilizado
antes un aparato similar si están bajo surpervision o reciben las instrucciones precisas
para un correcto y seguro manejo del termo, siendo conscientes de los peligros que
puede suponer.
• Los niños no deben jugar con el aparato.
• La limpieza y mantenimiento del termo no puede ser realizada por niños sin
supervisión.
16 Instrucciones de uso y mantenimiento
ES al cuerpo (si las placas no van ya incoporadas, deben ser acopladas al
cuerpo mediante los tornillos provistos). El termo quedará colgado
de la pared por la acción de dos ganchos (min. F 10 mm) jados
rmemente en la pared (no incluidos en el set de montaje). La
construcción de la placa que llevan los termos de montaje vertical es
universal y permite que la distancia entre los ganchos sea de 220 a 300
mm. 1a. En los termos de montaje horizontal las distancias entre los
ganchos son diferentes en funcion del modelo y estan mostradas en la
tabla 2. de g. 1c. para un montaje solar – g.1b.
Para evitar danos en el usuario y/o terceras personas en
caso de deterioro del sistema de suministro de agua
caliente es necesario que el aparato se monte en recintos
donde haya un hidroaislamiento de suelo y canerias de desague.
En ningun caso situe objetos debajo del termo que no sean
impermeables. En el caso de montar el aparato en recintos sin
hidroaislamiento de suelo es necesario que se instale una cubeta
de protección con canalizacion hacia la caneria de desagüe
debajo del aparato.
Observacion: el set de montaje no incluye la cubeta de protección
y es el usario el que debe elegirla.
2. Conexión del termo a la red de tuberias
Fig. 3a para un montaje vertical ; Fig. 3b para un montaje horizontal
Fig. 3c para un montaje de pie
Donde: 1. Tubo de entrada, 2. Válvula de seguridad 3. Válvula de
reduccion (en caso de una presión en en el suministro de agua de más
de 0.6 MPa), 4. Una válvula de parada 5. Embudo con una conexion al
desagüe. 6. Manguera 7. Grifo para descargar el agua.
Cuando se conecta el termo a la red de conduccion de agua hay que
tener en cuenta los signos de color indicadores (anillos) en los tubos: azul
– para agua fria /de entrada/, rojo – para el agua caliente /de salida/.
Es obligatorio que se monte la valvula de retorno de seguridad que
incorpora el termo. Esta se debe colocar en la entrada del agua fria,
siguiendo el sentido indicado por la echa, que indica la direccion de
entrada del agua. No se admite el montaje de llaves de paso adicionales
entre la válvula de retorno y el aparato.
Excepcion: Si las normativas locales requieren usar otra valvula de
seguridad o dispositivo (que cumplen la normas EN 1487 o EN 1489)
estos deben comprarse por separado. Para dispositivos que cumplen la
norma EN 1487, la presion maxima de trabajo anunciada debe ser de 0,7
MPa. Para otras valvulas de seguridad, la presion a la que son calibradas
debe ser 0,1MPa inferior que la indicada en la placa del aparato. En estos
casos, la valvula de retorno, que se suministra con el aparato, no debe
ser utilizada.
La presencia de otras /viejas/ válvulas de retorno puede
provocar un deterioro de su aparato, por lo que deben ser
eliminadas.
No se admiten otras llaves de paso entre la válvula de
seguridad y el aparato.
No se permite la jación de la válvula de retorno de seguridad
a cables de longitud superior a 10mm, en caso contrario esto
puede causar el deterioro de su válvula y será peligroso para su
aparato.
En los termos verticales, la válvula de protección debe estar
conectada a la tubería de entrada si el panel de plástico del
aparato está quitado. Después de su montaje, este debe adoptar la
posición marcada en la gura 2.
La válvula de seguridad y la tuberia entre la válvula y el termo
deben estar protegidos contra la congelación. Durante el
vaciado de la manguera, su extremo libre debe estar siempre abierto al
atmósfera (nunca sumergido). Asegúrese de que la manguera también
está protegida contra la congelación.
La apertura de la llave de agua fria de la red de suministro de agua y la
apertura de la llave de agua caliente del grifo de mezcla lleva a cabo el
llenado del termo de agua. Tras el completo llenado del termo, debe
comenzar un ujo constante de agua desde el grifo de mezcla de agua.
Ahora ya puede cerrar el grifo de agua caliente.
En el caso de que necesite vaciar el termo, primero debera cortar el
suministro electrico. Detenga igualmente el suministro de agua al
termo. Abra el grifo de agua caliente del grifo de mezcla. Abra el grifo 7
(Fig.4a y 4b) para descargar el agua del termo. En caso de que falte ese
grifo en la instalacion, vacie el termo de la siguiente manera:
• Modelos equipados con una válvula de palanca – levante la palanca
de la válvula y el agua saldrá por la apertura de drenaje.
• Modelos equpados con una valvula sin palanca – el agua puede
descargarse directamente del tubo de entrada de agua, desconectando
previamente el termo de las tuberias de agua.
Cuando se quita la brida es normal que uyan unos litros de agua,
procedentes del tanque de agua.
Cuando se extrae, deben adoptarse unas medidas de
prevención de daños por el agua que se derrama.
Si la presión en la red de agua supera los valores indicados en el párrafo
1, es necesaria la instalación de una válvula de reducción de presión,
de lo contrario el termo de agua no funcionará correctamente. El
fabricante no asume la fabricante de los problemas causados por el uso
incorrecto del aparato.
3. Conexión a la red eléctrica.
Antes de conectar la alimentación eléctrica, asegúrese de que
el aparato está lleno de agua.
3.1. Los modelos provistos con cable de alimentación con enchufe se
conectan insertando el enchufe en el contacto. Para apagarlo basta con
desconectar el enchufe del contacto.
La toma debe estar conectada a un circuito separado provisto de
un mecanismo de seguridad. Se debe estar conectado a tierra.
3.2. Termos de agua equipados con cable de alimentaciόn sin clavija
de enchufe
El aparato tiene que estar conectado a un circuito eléctrico separado
del cableado electrico estacionario. La conexión tiene que ser
constante - sin clavija de enchufe. El circuito debe estar provisto de
un fusible de seguridad y contar con un dispositivo incorporado para
asegurar la desconexión de todas las piezas eléctricas en caso de
sobretensión de la categoria III.
Los cables de alimentaciόn del aparato deben conectarse de la manera
siguiente:
• Cable de aislamiento marrόn - al cable de fase de la instalaciόn
eléctrica (L).
• Cable de aislamiento azul - al cable neutro de la instalaciόn eléctirca (N).
• Cable de aislamiento amarillo-verde - al cable protector de la
instalaciόn eléctrica ( ).
3.3. Termo de agua sin cable de alimentaciόn
El aparato debe conectarse a un circuito eléctrico individual de la
instalaciόn electrica ja, equipado con un fusible de seguridad con
corriente eléctrica nominal de 16A (20A para potencia > 3700W). La
conexiόn se realiza por cables de cobre con un hilo (sόlidos) – cable
3x2,5 mm2 para potencia total de 3000W (cable 3x4.0mm2 para
potencia > 3700W).
El circuito eléctrico debe contar con un dispositivo incorporado para
asegurar la desconexión de todas las piezas eléctricas en caso de
sobretensión de la categoria III.
Para conectar el cable de alimentación al termo, retire primero la tapa
de plástico (g. 2 a, b, c, d según el modelo comprado).
Conectar los cables de alimentación de la siguiente manera:
• cable correspondiente a fase conecte a señal A o 1 o L o L1.
• cable correspondiente a neutro conecte a señal N (B o B1 o N1).
• Es obligatoria la conexión del cable de seguridad a la junta de
tornillo con el enlace de tornillo, señalado con signo .
Después de montaje la tapa de plástico se pone de nuevo!
Aclaraciones de la g 2:
TS – interruptor térmico, TR – regulador térmico; S – interruptor (para los
modelos que lo tengan); R – calentador; IL – luz señal; F – elemento de
conexión; KL – mecanismo de lustre.
VI. PROTECCIÓN CONTRA CORROSIÓN ÁNODO DE MAGNESIO
EN AQUELLOS TERMOS CON REVESTIMIENTOVITROCERAMICO
El ánodo de magnesio protege la supercie interna del tanque de agua
contra corrosión.
Se trata de un elemento de sacricio que debe ser sometido a
revisiones periodicas y ser sustituido cuando sea preciso.
A la vista del uso a largo plazo y aun sin averias, el fabricante
recomienda realizar una inspección periódica del ánodo por un técnico
autorizado, así como su sustitución en caso de necesidad.
Para realizar el recambio, contacte a los servicios autorizados!
Other manuals for GCV6SL 804420 B11 TSR
1
Table of contents
Languages:
Other TESY Water Heater manuals
TESY
TESY GCR 802712 E32 EC User manual
TESY
TESY BiLight GCV 1004415 B11 TSR Specification sheet
TESY
TESY GCV6S 8047 Specification sheet
TESY
TESY GCVS 804420 B11 TSR Specification sheet
TESY
TESY BelliSlimo Lite User manual
TESY
TESY BelliSlimo DRY GCR 802724D E31 ECW User manual
TESY
TESY GCV 504716D C21 TS2RC User manual
TESY
TESY BelliSlimo DRY GCR 502724D E31 EC User manual
TESY
TESY BelliSlimo User manual
TESY
TESY GCV 303512 B11 TSR User manual
TESY
TESY Modeco Ceramic GCV 504716D C21 TS2RC User manual
TESY
TESY ModEco Classic GCV 1204720 C21 TSR Specification sheet
TESY
TESY Bilight Compact Specification sheet
TESY
TESY GCU 10 Series Guide
TESY
TESY GCV 504716D C22 ECW User manual
TESY
TESY GCV7/4S 150 44 30 B11 TSRCP Technical document
TESY
TESY BiLight GCV 120 4420 B11 TSR Specification sheet
TESY
TESY EV S 160 Series User manual
TESY
TESY Bilight Slim GCV 803520 B11 TSRC Specification sheet
TESY
TESY GCR 502712 E32 EC User manual
Popular Water Heater manuals by other brands
Wolter Systems
Wolter Systems 160 owner's manual
Heatstore
Heatstore HS10U Installation and user instructions
Modena
Modena EI 3D Series manual
Solarbeam
Solarbeam SB-300-D-HP Owner's handbook
Sime
Sime MURELLE HE 25 User instructions
Ace Heating Solutions
Ace Heating Solutions Mini-Pack Operating and maintenance instruction
Bosch
Bosch Highflow 17e Quick reference guide
State Water Heaters
State Water Heaters GP650YTPDT brochure
GE
GE GeoSpring GEH50DEEDSC Dimension Guide
Heatrae Sadia
Heatrae Sadia Multipoint 30 Installation and user instructions
Thermo Dynamics
Thermo Dynamics ELITE TDCH user manual
State Water Heaters
State Water Heaters GP6 50 Series instruction manual
Amana
Amana Remote HTM ERGW00121A P6819102F Service instructions
A.O. Smith
A.O. Smith Cyclone Xi Service handbook
Aspes
Aspes ATE30S Instructions for use and maintenance
heatwell
heatwell HWHM-TDF190/1.5-H31 Installation & owner's manual
Sun Bandit
Sun Bandit SB-30E-100200-3000 Installation and operation instruction manual
Bosch
Bosch Tronic 3000T ES 2.5 user manual