TEUCER WP-2TW User manual

Teucer`s 2 zone touch panel allows users to control 2
separate zones of lighng from a single wall unit. Using a RF
signal to control the LED lighng, removes the need to have
addional wiring between the wall panel and the receiver,
which allows greater exibility during installaon by
reducing installaon me and cabling costs.
WP-2TW and LRR-WTC
2 zone RF & WIFI controller and receiver for single colour LED strip
Product Descripon
Technical Specicaon
Brighter for longer
CONTROLLER AND RECEIVER
www.teucerled.co.uk
Controller
Order Code WP-2TW
Type RF wall panel, WIFI transmier
Input Voltage 12-24VDC
Operaon Frequency 868MHz
Dimension 86x86x29mm (WxLxH)
Power 10W driver LD-IP10/24
Receiver
Order Code LRR-WTC
Type RF receiver
Input Voltage 12-36VDC
Current 4X5A
Output 4X(60-180)W
Note Constant voltage
Dimension 46x178x22mm (WxLxH)
• Smartphone / tablet compable via Easy Lighng app
• Wireless RF range of 8-15 meters (depending on signal
obstacles within the installaon area)
• Control 2 zones independently
• Touch sensive glass
• 5%-100% smooth dimming
• Backlit buons for night me use
Features
RF technology allows for greater exibility when it
comes to controlling simple or complex lighng instal-
laons without the need of addional cabling.
There are some limitaons where installaons have
the receivers enclosed in electrical boxes or hidden
away in a ceiling , reducing the RF signal strength and
therefore the communicaon range.
In order to overcome these RF Signal restricons we
suggest the following when synchronising our RF con-
trollers and receivers:
• Keep the distance within 10 meters from the con-
troller to the receiver
• When expanding your lighng, always try and use
a signal repeater (PR-RGB), where possible.
• If your installaon requires several RF receivers,
ensure the “master” receiver is posioned in the
middle.
Recommendaon

Receiver wiring diagram
Controller layout
Brighter for longer
CONTROLLER AND RECEIVER
www.teucerled.co.uk
When wiring the receivers, it is important to make sure the total waage of the LED strips does not exceed the maximum
rated waage per channel of the receiver. Each chanel is rated at 5A, so the maximum waage per channel is 24x5A=120w.
The power supply has to match the rated volrage and be superior to the toal LED strip waage by a remcommended 10%.
Zone 1 Zone 2
ON and
dim up bu�on
OFF and
dim down bu�on
GND Vin 12-24VDC
LN
1
23
LRR-WTC
Learning Key
4
MASTER SLAVE
L
N
110V-230VACPower Supply
1
23
LRR-WTC
Learning Key
4
MASTER SLAVE
L
N
110V-230VACPower Supply
WP-2TW and LRR-WTC
2 zone RF & WIFI controller and receiver for single colour LED strip

Synchronising the controller to receiver
Brighter for longer
CONTROLLER AND RECEIVER
www.teucerled.co.uk
1) Ensure the wall panel is connected to a power source
3) Ensure the receiver has power. Press the learning key on the receiver.
4) Touch the ON buon on the zone you wish to synchronise the receiver to. The LED strip
will blink twice to conrm synchronisaon.
6) To clear the receiver from a selected zone, simply press and hold the learning key for 5 or
more seconds. The receiver will be reset to the default factory sengs.
1
23
LRR-WTC
Learning Key
4
MASTER SLAVE
close circuit for MASTER
open circtuit for SLAVE
WP-2TW and LRR-WTC
2 zone RF & WIFI controller and receiver for single colour LED strip
2) Set the receiver LRR-WTC as a MASTER OR SLAVE.
Allocang the receiver as a master or slave is important to ensure your LED strip and receiv-
er are fully synchronised. There can be only 1 master receiver per zone.
1
23
LRR-WTC
Learning Key
4
MASTER SLAVE
Learning key
Zone 1 Zone 2
ON bu�on
5) Just repeat the learning process to synchronise several receivers to the same controller.

Teucer (UK) Ltd
Head oce
Bedford House, Fulham Green, Fulham High Street,
London, SW6 3JW, UK
Tel: [phone]
Fax: [phone]
www.teucerled.co.uk
[e-mail]
Logiscs Centre
Trident Court,
1 Oakcro Road,
Chessington,
Surrey, KT9 1BD, London, UK
Tel: [phone], extension: 401
[e-mail]
Controlling your LED strip
Brighter for longer
CONTROLLER AND RECEIVER
www.teucerled.co.uk
With WP-2WT you can adjust brightnes of single colour LED strip.
• Press to turn ON/OFF the desired zone.
• Press and hold ON buon to increase the
brightness of your chosen zone.
• Press and hold OFF buon to decrease
the brightness of your chosen zone.
WP-2TW and LRR-WTC
2 zone RF & WIFI controller and receiver for single colour LED strip
Zone 1 Zone 2
ON bu�on
Warranty
• Products must be installed and serviced by qualied
electrician.
• Please ensure the receiver is mounted in a water proof
enclosure if installed in an outdoor environment,
avoiding metallic enclosures.
• Always ensure products are mounted in areas with
adequate venlaon to avoid overheang.
• Please ensure outputs of any power suppliers used in
conjucon with this product comply with its working
voltage.
• Never install product whilst connected to power and
double check connecons before switching on to
avoid short circuits.
Safety
Should this product fail during the 3 year warranty
period it will be replaced free of charge, subject to the
correct installaon of the original product in accordance
with applicable and appropriate electrical codes and
instrucons provided by Teucer, as well as subsequent
return of the faulty unit. Teucer does not accept
responsibility for any installaon costs associated with
the replacement of this product and Teucer reserves the
right to alter specicaons without prior noce. Teucer
can oer 5 year warranty upon request. For further
informaon, please see our Terms and Condions.
www.teucerled.co.uk/terms-and-condions/