Tevion 82663 User manual

Helpline No. UK/ North Ireland 0871 37 61 020 Rep. Ireland 1-800-992 508
Web Support www.medion.co.uk
Model Number: 82663
3
Introduction 1
Congratulations on choosing to buy a Tevion® product. By doing so you now have the
assurance and peace of mind that comes with purchasing a product made by one of
the leading manufacturers.
All products brought to you by Tevion® are manufactured to the highest standards of
performance and safety, and, as part of our philosophy of customer service and
satisfaction, are backed by our comprehensive 3 Year Warranty.
Please fill in and return the Warranty Card to the address provided.
We hope you will enjoy using your purchase for many years to come.

Helpline No. UK/ North Ireland 0871 37 61 020 Rep. Ireland 1-800-992 508
Web Support www.medion.co.uk
Model Number: 82663
4
Safety instructions 2
About this manual
Please read these instructions carefully before operating the remote
control. Keep the instructions in a safe place for future reference or in
case you need to pass them on to someone else.
General information
Do not attempt to repair the remote control yourself.
The universal remote control contains an infrared laser class 1 diode. The device has a
safety system that prevents the emission of dangerous laser rays escaping from the
device during normal use. In order to avoid injury to the eyes, never interfere with or
damage the unit's security system.
Do not subject your remote control to dust, strong sunlight, moisture, high
temperatures or strong vibrations.
Battery instructions
Keep children away from the batteries. Seek medical attention immediately in the
event of a battery being swallowed.
Before inserting the batteries, check whether the contacts in the device and batteries
are clean and, if necessary, clean them.
Only use new batteries. Never use old and new batteries together.
Do not use a combination of battery types.
Please note the polarity (+/-) when inserting the batteries.
WARNING! There is a risk of explosion if batteries are incorrectly replaced. Replace the
batteries only with the same or equivalent type.
Never try to recharge non-rechargeable batteries. There is a risk of an explosion!
Store batteries in a cool, dry location. Direct strong heat can damage the batteries. For
that reason do not expose the device to any sources of strong heat.
Never short-circuit the batteries.Never throw batteries into a fire.
If the appliance is not going to be used for long periods, remove the batteries.
Immediately remove leaking batteries from the device. Clean the contacts before
inserting new batteries. There is a risk of corrosion due to battery acid!
Also remove dead batteries from the device.
Cleaning
Clean the device with a dry or lightly dampened, lint free cloth. Do not use any
corrosive or aggressive cleaning products.
Included in the box 3
Check that nothing is missing from the packaging and inform us of any missing party
within 14 days after purchase. The delivery of the device you have purchased includes:
Universal remote control
2x LR03 AAA micro batteries
Remote control stand

Helpline No. UK/ North Ireland 0871 37 61 020 Rep. Ireland 1-800-992 508
Web Support www.medion.co.uk
Model Number: 82663
5
Product description 4
This universal remote control has eight mode keys and therefore can replace up to
eight normal remote controls ("8 in 1 function“). These may be remote controls for
practically every type of remote-controlled consumer electronics (see the supplied
code list).
The labels "TV" "VCR" "DVD" "CD" "ASAT" "CBL" "AUX" "DSAT" on the mode keys
are for overview purposes. With the exception of the TV key, you can assign any key
to any device (“Flex Mode”). To program in codes see “Programming device codes” on
page 10.
Preparations 5
Inserting batteries
2x LR03 AAA micro batteries are supplied.
Remove the battery compartment cover by pushing it downwards.
Insert both batteries into the compartment while observing the +/-
polarity.
Replace the cover.
Settings after battery replacement
If the batteries have been inserted correctly, the factory
setting is displayed. It shows the active mode ("TV"), the
day of the week and the time.
Please read “Setting time and date” on page 8 for more
information on setting the time and date.
After new batteries have been inserted, the mode, time, date and backlight time are
reset to the factory settings.
However, codes that have already been programmed in as well as programmed learn
functions and macros are retained when batteries are changed.
Protection against unexpected battery discharging
If a key remains pressed down by accident (because something is lying on the remote
control for example), the remote control sends 255 infrared signals (for approximately
30 seconds) and this ends the transmission. This prevents the batteries from
discharging accidentally.
Remote control stand
You can use the stand for your remote control to place it visibly and easy accessible on
a table top.

Helpline No. UK/ North Ireland 0871 37 61 020 Rep. Ireland 1-800-992 508
Web Support www.medion.co.uk
Model Number: 82663
6
Overview 6
Device
1Switch source on/off
2Double spaced LCD display with
background
3Mode keys for selecting the device
4Video text keys:
: Video text on
: Video text off
: Video text hold
: Video text / TV mix
: Screen displays
5Mute
6Joystick: navigate up, down, left, right.
Select approprivate arrow direction; press
joystick: OK
7Set volume
8Electronic Program Guide: Electronic TV
programming; ShowView function
9Exit menu
10 Automatic shutdown
11 Number keys for entering codes and
programme selection; keys 1-3: save
macros
12 Enter double-spaced numbers
13 Playback control:
: Start playback
/: Playback fast backward/forward
: Recording
: Playback stop
: Playback pause
14 AV mode
15 press and hold: opens programming mode
(e.g. for entering a device code) press
briefly: Display date (instead of time)
16 Programming macros
17 Open menu
18 Programmme selection
19 press once to switch one device to and from standby mode; press twice to switch
all devices to and from standby mode
Display
1Alternating text displays
2IR signal is being transmitted
3Setup mode is active
4Timer is active
5TV sleep timeer is active
6Time format: AM/PM
7Date, time or device code

Helpline No. UK/ North Ireland 0871 37 61 020 Rep. Ireland 1-800-992 508
Web Support www.medion.co.uk
Model Number: 82663
7
Standard display – time
In the standard display:
the active mode appears in the first column (device type).
the day of the week and time appears in the second column.
Date
Press the SETUP key briefly 1to show:
the symbol for the activated SHIFT function2(S) in the first
column;
the date in the second column.
Please read “Setting time and date” on page 8 for more information on setting the
time and date.
Select mode or device
Use a mode key to select the mode or the device that was programmed to this mode
key. In the display:
the name of the mode key appears in the first column;
this device's programmed code appears in the second column.
Please refer to “Programming device codes” on page 10 for
more information on programming the device code.
Navigating the menus 7
To open the Setup menu, press and hold the SETUP key until CODE SETUP appears
along with the SET symbol in the display.
If the display shows CODE SETUP continue to press the SETUP key to access the other
menus:
CODE SETUP > SYSTEM SETUP > TIMER SETUP > LEARN SETUP > MACRO SETUP > EXIT
SETUP.
Press OK to open a menu.
Press the arrows to switch between sub-menus .
To exit the Setup menu, press the EXIT key and confirm the EXIT SETUP display with
OK.
Cancel function
If you wish to cancel a process, wait approx. 30 seconds. The
Setup menu closes automatically and the TIMEOUT message
appears.
1Press and hold the SETUP key to open the CODE SETUP(see next chapter).
2Most keys can be assigned two functions (cf. Page 18). You can access the
second function by first activating the SHIFT function.

Helpline No. UK/ North Ireland 0871 37 61 020 Rep. Ireland 1-800-992 508
Web Support www.medion.co.uk
Model Number: 82663
8
Setting time and date 8
In the standard display, the day and time appear in the lower column.
Press the SETUP key briefly to show the date in the lower column for approx. 30
seconds.
Setting clock time
Keep the Setup key pressed down for approx. 3 seconds, until
CODE SETUP appears.
Press SETUP again briefly to open the SYSTEM SETUP.
Confirm with OK. The VOL/MUTE SETUP is displayed.
Use the arrows to select the TIME SETUP and confirm with
OK.
The current time format flashes. Use the arrows to select 
the 12 or 24 HR time format ) and confirm with OK (see the end
of the section).
The hour display flashes. Use the arrows to select  the
hour and confirm by pressing OK.
The minute display flashes. Use the arrows to select  the
number of minutes and confirm by pressing OK.
The message SUCCESS appears and the display returns to CODE
SETUP.
If you choose 12 HR format, the time is displayed with the AM
or PM symbols.
Setting the date
Open SYSTEM SETUP as above.
Confirm with OK. The VOL/MUTE SETUP is displayed.
Use the arrows to select the DATE SETUP (press twice) and
confirm with OK.
The year flashes. Use the arrows to select  the year and
confirm by pressing OK.
The month flashes. Use the arrows to select  the month
and confirm by pressing OK.
The day (DATE) flashes. Use the arrows to select  the day
and confirm by pressing OK.
The day (DAY) flashes. Use the arrows to select  the day
of the week and confirm by pressing OK.
The message SUCCESS appears and the display returns to
CODE SETUP.

Helpline No. UK/ North Ireland 0871 37 61 020 Rep. Ireland 1-800-992 508
Web Support www.medion.co.uk
Model Number: 82663
9
Backlight 9
The display's backlight comes on each time the button is pressed. The backlight's
factory setting is for 10 seconds. You can switch off the backlight or extend it to 60
seconds.
Please note that the backlight uses up additional battery life.
Keep the SETUP key pressed down for approx. 3 seconds,
until CODE SETUP appears.
Press SETUP again briefly to open SYSTEM SETUP.
Confirm with OK. The VOL/MUTE SETUP is displayed.
Use the arrows (press three times) to select the BACKLIGHT
SETUP and confirm with OK.
The current set time flashes (factory setting is for 10 seconds).
Use the arrows to select  the required time span in five
second intervals.
In order to switch the backlight off, select 00 seconds. Confirm
with OK.
The confirmation message SUCCESS appears and the display
returns to CODE SETUP.

Helpline No. UK/ North Ireland 0871 37 61 020 Rep. Ireland 1-800-992 508
Web Support www.medion.co.uk
Model Number: 82663
10
Programming device codes 10
For every device that you would like to operate using the universal remote control,
you must program a four-digit device code to a mode key (TV, VCR, DVD, CD,
ASAT, ASAT, CBL, AUX). The names on the keys are only for reminder purposes.
With the exception of the TV key you can assign any key to any device (“Flex Mode”).
The TV mode key can only be assigned to TV device codes.
Your universal remote control is pre-programmed with proprietary codes from Tevion
devices and its most important functions can be used with proprietary Tevion devices
without requiring any extra programming.
Device types and code groups
You can choose between the following device types when programming in codes:
TV TV set, projector, plasma screen, LCD;
VCR Video recorder;
LD Laser disc player;
DVD DVD player;
DVR Digital video recorder;
HDD Hard disk drive;
SAT Satellite receivers (analogue, digital);
CABLE Cable box, Pay TV decoder;
DVBT DVB-T receivers;
STB Set top box;
AUDIO Audio device;
AMP Amplifier;
RECR Receiver (combined radio and amplifier);
HTIB Home Cinema;
MP3 MP3 player;
CD CD player;
TAPE Cassette players;
TUNER Radio;
PHONO Record player.
Assigment to code groups
Each type of device is assigned to a group of device codes. When you select a device
type, the appropriate code group is searched to find a device code. Device types are
assigned as follows:
Device type Code group
TV TV
VCR, LD, DVD, DVR, HDD, HTIB VCR/DVD
SAT, CABLE, DVB-T, STB, CBL/SAT
AUDIO, AMP, RECR, MP3, CD, TAPE, TUNER, PHONO,
HTIB (some)
CD/AUDIO

Helpline No. UK/ North Ireland 0871 37 61 020 Rep. Ireland 1-800-992 508
Web Support www.medion.co.uk
Model Number: 82663
11
Programming options 11
The following sections describe the different methods for finding a device code:
by selecting a code for a certain device type in the display,
according to the enclosed Code List,
by running a search,
by brand name.
For combined devices (e.g. TV set with video recorder, TV set with DVD player, DVD
and video recorder) it is often necessary to assign two mode keys with the respective
code for each part of the device (e.g. the TV mode key for TV functions and a different
mode key for the VCR or DVD functions). However, there are also combined devices
with only one code for both device parts (see also “Operating combined devices” on
page 16).
Open programming mode
To open the programming mode, press and hold the SETUP
key until CODE SETUP appears along with SET in the display.
Select device code in the display
Switch on the device to be controlled.
Keep the SETUP key pressed down for approx. 3 seconds,
until CODE SETUP appears.
Press OK. The LIST CODES menu is displayed.
Press OK. The MODE KEY display appears.
Press the required mode key (TV, VCR, DVD, CD, ASAT, CBL,
AUX, DSAT). In the display you see the words DEVICE? TV.
Use the arrows to select  the device type to be
programmed on this mode key. (If you select TV it is not
possible to select a device type because only TV codes can be
programmed on the TV mode key.)
Please refer to the list and table above.
Press OK. PLEASE WAIT appears in the display. The codes for
the device group that contains the previously selected device
type are now scanned in order of brand name (cf. the
enclosed code list). The first entry is displayed in alphabetical
order with the first code.
Use the arrows to select  the brand name of your device.
The first code is shown.
Use the arrows to select a device code  for this brand name.
Now try the universal remote control with your device. To do this, (depending on the
device type) use the following keys POWER , 0 – 9, VOL, P+/–, AV, Mute ,
Video text as well as the six playback keys.
If the device does not respond as expected, select a different
code.
When you have found a suitable device code, press OK to save
the code. PLEASE WAIT appears again in the display, followed
by the confirmation message SUCCESS.
The remote control returns to normal operation.

Helpline No. UK/ North Ireland 0871 37 61 020 Rep. Ireland 1-800-992 508
Web Support www.medion.co.uk
Model Number: 82663
12
Entering the device code according to the code list
The codes of the corresponding devices can be found in the code list enclosed with
these operating instructions.
Switch on the device to be controlled.
Keep the SETUP key pressed down for approx. 3 seconds,
until CODE SETUP appears.
Press OK. LIST CODES now appears in the display.
Use the arrows to select the ENTER CODES menu.
Press OK. The MODE KEY display appears.
Press the required mode key (TV, VCR, DVD, CD, ASAT, CBL,
AUX, DSAT). The mode key label is displayed with the current
code.
Use the number keys to select the preferred code from the
code list. After you enter the fourth digit, the confirmation
message SUCCESS is displayed.
The remote control returns to normal operation.
If an incorrect code is entered, the error message CODE ERROR
appears. – The universal remote control then switches to
normal operation.
Entering the device code for a Sky Box
To program the universal remote control to operate your Sky Box, please select one of
the following device codes and follow the instructions for “Entering the device code
according to the code list” below.
For Sky Digital use 0584
For Sky+ (Sky Plus) use 0555
For Sky+HD (High Definition) use 1151
For a short overview of the Sky keys on this device, see “Sky Box keys” on page 25.
Please refer to your Sky Owner Manual for operating your Sky Box.