Tews Technologies TPMC533 User manual

The Embedded I/O Company
TPMC533
32x ADC, 16x/0x DAC and 8x Digital I/O
Version 1.0
User Manual
Issue 1.0.1
May 2018
TEWS TECHNOLOGIES GmbH
Am Bahnhof 7
25469 Halstenbek, Germany
Phone: [phone]
Fax: [phone]
e-mail: [email protected]
www.tews.com

TPMC533 User Manual Issue 1.0.1 Page 2 of 107
TPMC533-10R
32 Channels of Simultaneous Sampling
Differential 16 bit A/D, 16
Channels of
Simultaneous Update Single-
Ended 16 bit D/A
and 8 Channels of TTL Digital
I/O, with
HDRA100 front panel I/O
(RoHS compliant)
TPMC533-20R
32
Channels of Simultaneous Sampling
Differential 16 bit A/D and 8 Cha
nnels of TTL
Digital I/O, with HDRA100 front panel I/O
(RoHS compliant)
This document contains information, which is
proprietary to TEWS TECHNOLOGIES GmbH. Any
reproduction without written permission is forbidden.
TEWS TECHNOLOGIES GmbH has made any
effort to ensure that this manual is accurate and
complete. However TEWS TECHNOLOGIES GmbH
reserves the right to change the product described
in this document at any time without notice.
TEWS TECHNOLOGIES GmbH is not liable for any
damage arising out of the application or use of the
device described herein.
Style Conventions
Hexadecimal characters are specified with prefix 0x,
i.e. 0x029E (that means hexadecimal value 029E).
For signals on hardware products, an ‚Active Low’ is
represented by the signal name with # following, i.e.
IP_RESET#.
Access terms are described as:
W Write Only
R Read Only
R/W Read/Write
R/C Read/Clear
R/S Read/Set
2017-2018 by TEWS TECHNOLOGIES GmbH
All trademarks mentioned are property of their respective owners.

TPMC533 User Manual Issue 1.0.1 Page 3 of 107
Issue
Description
Date
1.0.0 Initial issue December 2017
1.0.1 Power Requirements revised May 2018

TPMC533 User Manual Issue 1.0.1 Page 4 of 107
Table of Contents
1PRODUCT DESCRIPTION ...........................................................................................8
2TECHNICAL SPECIFICATION ...................................................................................10
3PCI INTERFACE.........................................................................................................12
Identifiers.......................................................................................................................................123.1
PCI Base Address Register Configuration.................................................................................123.2
3.2.1 Register Space .......................................................................................................................13
3.2.2 Correction Data ROM .............................................................................................................75
4I/O ELECTRICAL INTERFACE...................................................................................86
ADC ................................................................................................................................................864.1
DAC ................................................................................................................................................874.2
Digital I/O and P14 Back I/O.........................................................................................................884.3
5DATA CODING ...........................................................................................................89
ADC ................................................................................................................................................895.1
DAC ................................................................................................................................................905.2
6CORRECTION DATA..................................................................................................91
7OPERATING MODES.................................................................................................92
Manual Mode .................................................................................................................................927.1
7.1.1 DAC Immediate Conversion...................................................................................................92
7.1.2 DAC Controlled Conversion....................................................................................................92
Sequencer Mode ...........................................................................................................................937.2
7.2.1 Normal Mode ..........................................................................................................................94
7.2.2 Frame Mode............................................................................................................................95
8SEQUENCER..............................................................................................................96
Host RAM Data Buffers ................................................................................................................978.1
8.1.1 ADC ........................................................................................................................................98
8.1.2 DAC ......................................................................................................................................100
9CONVERSION SIGNALS..........................................................................................101
Multi-board Synchronization .....................................................................................................1039.1
10 PIN ASSIGNMENT – I/O CONNECTOR...................................................................104
Front I/O .......................................................................................................................................10410.1
P14 Back I/O ................................................................................................................................10510.2
11 TA114 CABLE...........................................................................................................106
X2 Connector...............................................................................................................................10611.1
X3 Connector...............................................................................................................................10711.2

TPMC533 User Manual Issue 1.0.1 Page 5 of 107
List of Figures
FIGURE 1-1 : BLOCK DIAGRAM......................................................................................................................9
FIGURE 4-1 : DIGITAL I/O AND P14 BACK I/O SCHEME.............................................................................88
FIGURE 7-1 : NORMAL MODE ......................................................................................................................94
FIGURE 7-2 : TIMING IN NORMAL MODE....................................................................................................94
FIGURE 7-3 : FRAME MODE .........................................................................................................................95
FIGURE 7-4 : TIMING IN FRAME MODE.......................................................................................................95
FIGURE 8-1 : ADC SEQUENCER ..................................................................................................................96
FIGURE 8-2 : DAC SEQUENCER ..................................................................................................................96
FIGURE 9-1 : CONVERSION SIGNALS.......................................................................................................101
FIGURE 9-2 : GLOBAL CONVERSION SIGNALS TIMING REQUIREMENTS ...........................................102
List of Tables
TABLE 2-1 : TECHNICAL SPECIFICATION...................................................................................................11
TABLE 3-1 : PCI IDENTIFIER.........................................................................................................................12
TABLE 3-2 : PCI BASE ADDRESS REGISTERS...........................................................................................12
TABLE 3-3 : REGISTER SPACE ....................................................................................................................18
TABLE 3-4 : REGISTER BIT ACCESS TYPES..............................................................................................19
TABLE 3-5 : GLOBAL ADC CONTROL REGISTER.......................................................................................19
TABLE 3-6 : GLOBAL ADC STATUS REGISTER..........................................................................................20
TABLE 3-7 : ADC CONFIGURATION REGISTER..........................................................................................21
TABLE 3-8 : ADC CORRECTION REGISTER A............................................................................................22
TABLE 3-9 : ADC CORRECTION REGISTER B............................................................................................22
TABLE 3-10: ADC CORRECTION REGISTER C...........................................................................................22
TABLE 3-11: ADC CORRECTION REGISTER D...........................................................................................22
TABLE 3-12: ADC CORRECTION REGISTER E...........................................................................................22
TABLE 3-13: ADC CORRECTION REGISTER F ...........................................................................................23
TABLE 3-14: ADC CORRECTION REGISTER G...........................................................................................23
TABLE 3-15: ADC CORRECTION REGISTER H...........................................................................................23
TABLE 3-16: ADC DATA REGISTER A & B...................................................................................................24
TABLE 3-17: ADC DATA REGISTER C & D...................................................................................................24
TABLE 3-18: ADC DATA REGISTER E & F...................................................................................................24
TABLE 3-19: ADC DATA REGISTER G & H ..................................................................................................24
TABLE 3-20: ADC MODE REGISTER............................................................................................................25
TABLE 3-21: ADC SEQUENCER CONTROL REGISTER .............................................................................27
TABLE 3-22: ADC SEQUENCER STATUS REGISTER.................................................................................29
TABLE 3-23: NUMBER OF CONVERSIONS REGISTER..............................................................................30
TABLE 3-24: CONVERSION COUNT REGISTER .........................................................................................30

TPMC533 User Manual Issue 1.0.1 Page 6 of 107
TABLE 3-25: FIFO LEVEL REGISTER...........................................................................................................31
TABLE 3-26: DMA BUFFER BASE ADDRESS REGISTER...........................................................................31
TABLE 3-27: DMA BUFFER LENGTH REGISTER ........................................................................................31
TABLE 3-28: DMA BUFFER NEXT ADDRESS REGISTER...........................................................................31
TABLE 3-29: DMA STATUS BASE ADDRESS REGISTER...........................................................................32
TABLE 3-30: DMA STATUS (HOST RAM) .....................................................................................................32
TABLE 3-31: GLOBAL DAC CONTROL REGISTER......................................................................................33
TABLE 3-32: GLOBAL DAC STATUS REGISTER.........................................................................................34
TABLE 3-33: DAC CONFIGURATION REGISTER ........................................................................................37
TABLE 3-34: DAC CORRECTION REGISTER A...........................................................................................38
TABLE 3-35: DAC CORRECTION REGISTER B...........................................................................................38
TABLE 3-36: DAC CORRECTION REGISTER C...........................................................................................38
TABLE 3-37: DAC CORRECTION REGISTER D...........................................................................................38
TABLE 3-38: DAC DATA REGISTER A & B...................................................................................................39
TABLE 3-39: DAC DATA REGISTER C & D...................................................................................................39
TABLE 3-40: DAC STATUS REGISTER.........................................................................................................40
TABLE 3-41: DAC MODE REGISTER............................................................................................................41
TABLE 3-42: DAC SEQUENCER CONTROL REGISTER .............................................................................44
TABLE 3-43: DAC SEQUENCER STATUS REGISTER.................................................................................46
TABLE 3-44: NUMBER OF CONVERSIONS REGISTER..............................................................................46
TABLE 3-45: CONVERSION COUNT REGISTER .........................................................................................47
TABLE 3-46: FIFO LEVEL REGISTER...........................................................................................................47
TABLE 3-47: DMA BUFFER BASE ADDRESS REGISTER...........................................................................47
TABLE 3-48: DMA BUFFER LENGTH REGISTER ........................................................................................47
TABLE 3-49: DMA BUFFER NEXT ADDRESS REGISTER...........................................................................48
TABLE 3-50: CONVERSION CLOCK 1 GENERATOR REGISTER...............................................................49
TABLE 3-51: CONVERSION CLOCK 2 GENERATOR REGISTER...............................................................50
TABLE 3-52: FRAME TRIGGER GENERATOR REGISTER 1 ......................................................................51
TABLE 3-53: FRAME TRIGGER GENERATOR REGISTER 2 ......................................................................51
TABLE 3-54: CONVERSION SIGNALS GENERATOR ENABLE REGISTER...............................................52
TABLE 3-55: CONVERSION SIGNALS GENERATOR OUTPUT DRIVER REGISTER................................53
TABLE 3-56: CONVERSION SIGNALS SOURCE SELECTION REGISTER ................................................54
TABLE 3-57: FRAME TIMER REGISTER.......................................................................................................55
TABLE 3-58: DIO INPUT REGISTER .............................................................................................................56
TABLE 3-59: DIO INPUT FILTER DEBOUNCE REGISTER..........................................................................57
TABLE 3-60: DIO OUTPUT REGISTER .........................................................................................................58
TABLE 3-61: DIO OUTPUT ENABLE REGISTER..........................................................................................59
TABLE 3-62: INTERRUPT ENABLE REGISTER............................................................................................62
TABLE 3-63: ERROR INTERRUPT ENABLE REGISTER .............................................................................65
TABLE 3-64: DIO RISING EDGE INTERRUPT ENABLE REGISTER ...........................................................66
TABLE 3-65: DIO FALLING EDGE INTERRUPT ENABLE REGISTER.........................................................67
TABLE 3-66: INTERRUPT STATUS REGISTER............................................................................................68
TABLE 3-67: ERROR INTERRUPT STATUS REGISTER .............................................................................69

TPMC533 User Manual Issue 1.0.1 Page 7 of 107
TABLE 3-68: DIO INTERRUPT STATUS REGISTER....................................................................................70
TABLE 3-69: GLOBAL CONFIGURATION REGISTER..................................................................................71
TABLE 3-70: DIO PULL RESISTOR REGISTER ...........................................................................................72
TABLE 3-71: P14 BACK I/O PULL RESISTOR REGISTER...........................................................................72
TABLE 3-72: CORRECTION DATA EEPROM CONTROL/STATUS REGISTER..........................................73
TABLE 3-73: TEMPERATURE SENSOR TRIGGER REGISTER ..................................................................74
TABLE 3-74: TEMPERATURE SENSOR DATA REGISTER.........................................................................74
TABLE 3-75: FIRMWARE VERSION REGISTER...........................................................................................74
TABLE 3-76: CORRECTION DATA ROM.......................................................................................................85
TABLE 4-1 : ADC ELECTRICAL INTERFACE................................................................................................86
TABLE 4-2 : ADC INPUT SCHEMES..............................................................................................................86
TABLE 4-3 : DAC ELECTRICAL INTERFACE................................................................................................87
TABLE 4-4 : DIGITAL I/O AND P14 BACK I/O ELECTRICAL INTERFACE ..................................................88
TABLE 5-1 : ADC DATA CODING EXAMPLE................................................................................................89
TABLE 5-2 : ADC DATA CODING, BIPOLAR INPUT RANGE.......................................................................89
TABLE 5-3 : DAC DATA CODING, UNIPOLAR OUTPUT RANGE................................................................90
TABLE 5-4 : DAC DATA CODING, BIPOLAR OUTPUT RANGE...................................................................90
TABLE 8-1 : HOST RAM DATA BUFFER EXAMPLE I...................................................................................98
TABLE 8-2 : HOST RAM DATA BUFFER EXAMPLE II..................................................................................99
TABLE 8-3 : HOST RAM DATA BUFFER EXAMPLE I.................................................................................100
TABLE 8-4 : HOST RAM DATA BUFFER EXAMPLE II................................................................................100
TABLE 9-1 : GLOBAL CONVERSION SIGNALS TIMING REQUIREMENTS..............................................102
TABLE 9-2 : GENERATOR ENABLE, GENERATOR OUTPUT DRIVER AND SOURCE SELECTION
SETTINGS FOR DIFFERENT SYSTEM CONFIGURATIONS................................................103
TABLE 10-1: PIN ASSIGNMENT FRONT I/O...............................................................................................104
TABLE 10-2: PIN ASSIGNMENT P14 BACK I/O..........................................................................................105
TABLE 11-1 : TA114 X2 CONNECTOR........................................................................................................106
TABLE 11-2 : TA114 X3 CONNECTOR........................................................................................................107

TPMC533 User Manual Issue 1.0.1 Page 8 of 107
1 Product Description
The TPMC533 is a standard single-wide PCI Mezzanine Card (PMC) compatible module providing 32
channels of simultaneous sampling true differential bipolar 16bit analog input, 16 or no channels of
simultaneous update single-ended unipolar/bipolar 16bit analog output and 8 channels of tri-state 5V-tolerant
TTL digital input/output. All signals are accessible through a HDRA100 type front I/O connector.
The PMC-Connectors P11 and P12 provide access to the control logic via a 32bit 33MHz PCI interface.
The ADCs offer true differential inputs with software selectable ±5V and ±10V bipolar input voltage ranges
(one common setting for all eight channels of each ADC). The maximum sample rate of the ADCs is
200kSPS and they offer an oversampling capability with digital filter.
The DACs offer software selectable 0-5V, 0-10V, 0-10.8V, ±5V, ±10V and ±10.8V output voltage ranges
(individual setting for each of the four channels of each DAC). The settling time is typically 10μs and the DAC
channels are capable to drive a load of 2kΩ, with a capacitance up to 4000pF.
Each TPMC533 is factory calibrated. The correction data is stored in an on-board serial EEPROM unique to
each PMC module. These correction values can be used to perform a hardware correction of every analog-
to-digital and digital-to-analog conversion. Additionally, measurement data read out of a temperature sensor
on-board can be used to compensate temperature dependent errors.
The TPMC533 provides two Sequencers, one for AD Conversions and another one for DA Conversions. To
perform periodic simultaneous conversions the conversion rates are programmable and can be output to
other modules on PMC Back I/O Connector P14 or Front I/O Connector DIO pins for synchronization
purposes. The TPMC533 can also operate as a target which means that the conversion rates can be
sourced from P14 or Front I/O, created by another module.
A Frame Trigger signal, which can also either be generated by the TPMC533 and output on P14/Front I/O or
generated by other modules and input from P14/Front I/O, can be used to synchronize ADC frames and
DAC frames.
The signals on PMC Back I/O Connector P14 are ESD protected and driven or read by tri-state 5V-tolerant
TTL buffers.
To be able to collect ADC frames and to output DAC frames the TPMC533 provides input and output FIFOs.
Data transfer on the PCI bus is handled by TPMC533 initiated block transfer mode DMA cycles with
minimum host/CPU intervention.
The 8 Digital TTL tri-state I/O lines with 4.7kΩ pull resistors are ESD protected. The voltage, the pull
resistors are connected to, is programmable by software and can be 3.3V, 5V, GND or floating level (one
common setting for all eight Digital I/Os). All 8 DIOs can be programmed whether to have their Digital I/O
transmitters enabled or disabled individually per I/O line. The Digital I/O receivers are always enabled, so
each DIO level can always be monitored and can generate an interrupt, triggered on rising edge, falling edge
or both. Additionally, a debounce filter can be configured to get rid of bounce on the Digital I/O lines.

TPMC533 User Manual Issue 1.0.1 Page 9 of 107
Figure 1-1 : Block Diagram

TPMC533 User Manual Issue 1.0.1 Page 10 of 107
2 Technical Specification
PMC Interface
Mechanical Interface
PCI Mezzanine Card (PMC) Interface confirming to IEEE
P1386/P1386.1
Standard single-wide
Electrical Interface
PCI Rev. 3.0 compatible
33MHz / 32bit PCI
Initiator/Target
3.3V and 5V PCI Signaling Voltage
On-Board Devices
FPGA Spartan-6 (Xilinx)
ADC AD7609 (Analog Devices)
DAC AD5754R (Analog Devices)
Digital I/O 74LVT126 (NXP)
Non-Volatile Memory
FPGA Configuration: 32 Mbit
Serial Flash
W25Q32JV (Winbond)
Correction Data: 16 Kbit Serial
EEPROM M93C86-W (ST)
ADC Interface
Number of ADC Channels 32
Input Type True bipolar differential
Input Voltage Ranges ±5V and ±10V
(one common setting for all eight channels of each ADC)
Sample Rate
200kSPS
DAC Interface
Number of DAC Channels TPMC533-10R: 16
TPMC533-20R: 0
Output Type Unipolar/bipolar single-ended
Output Voltage Ranges ±5V, ±10V, ±10.8V, +5V, +10V and +10.8V
(individual setting for each of the four channels of each DAC)
Settling Time
10µs
DIO Interface
Number of DIO Channels
8
Driver Level
LVTTL (3.3V)
Receiver
5V tolerant
Source Current
15mA
Sink Current
6mA
I/O Connectors
Front I/O
100-pin HDRA (Honda HDRA-EC100LFDT-SL+ or compatible)
P14 Back I/O
64-pin Mezzanine Connector (Molex 71436-2864 or compatible)

TPMC533 User Manual Issue 1.0.1 Page 11 of 107
Physical Data
Power Requirements 550mA max. @ +5V DC (without I/O Load)
Temperature Range Operating
Storage -40°C to +85°C -40°C to +85°C
MTBF
TPMC533-10R: 487000h
TPMC533-20R: 497000h
MTBF values shown are based on calculation according to MIL-HDBK-217F and
MIL-HDBK-217F Notice 2; Environment: GB20°C.
The MTBF calculation is based on component FIT rates provided by the
component suppliers. If FIT rates are not available, MIL-HDBK-217F and
MIL-HDBK-217F Notice 2 formulas are used for FIT rate calculation.
Humidity 5 – 95 % non-condensing
Weight TPMC533-10R: 72.8g
TPMC533-20R: 72.5g
Table 2-1 : Technical Specification

TPMC533 User Manual Issue 1.0.1 Page 12 of 107
3 PCI Interface
Identifiers3.1
Vendor-ID
0x1498 (TEWS TECHNOLOGIES)
Device-ID
0x0215 (TPMC533)
Class Code 0x118000 (Other data acquisition/signal
processing controllers)
Subsystem Vendor-ID
0x1498 (TEWS TECHNOLOGIES)
Subsystem Device-ID 0x000A (TPMC533-10R)
0x0014 (TPMC533-20R)
Table 3-1 : PCI Identifier
PCI Base Address Register Configuration3.2
The two address spaces on the TPMC533 are accessed from the PCI side by addressing two PCI Base
Address Registers mapped in the PCI Memory Space.
PCI Base Address Register
(Offset in PCI
Configuration Space)
PCI
Space
Mapping
Size
(Byte) Port
Width
(Bit)
Endian
Mode Description
0 (0x10) MEM 1024 32 Little Register Space
1 (0x14) MEM 2048 32 Little Correction Data ROM
Table 3-2 : PCI Base Address Registers

TPMC533 User Manual Issue 1.0.1 Page 13 of 107
3.2.1 Register Space
PCI Base Address Register 0 (Offset 0x10 in PCI Configuration Space).
Offset to BAR0 Description Size (Bit)
ADC Global Registers
0x000 Global ADC Control Register 32
0x004 Global ADC Status Register 32
0x008 Reserved -
0x00C Reserved -
ADC Device Registers
0x010 ADC1 Configuration Register 32
0x014 Reserved -
0x018 ADC1 Correction Register A 32
0x01C ADC1 Correction Register B 32
0x020 ADC1 Correction Register C 32
0x024 ADC1 Correction Register D 32
0x028 ADC1 Correction Register E 32
0x02C ADC1 Correction Register F 32
0x030 ADC1 Correction Register G 32
0x034 ADC1 Correction Register H 32
0x038 ADC1 Data Register A & B 32
0x03C ADC1 Data Register C & D 32
0x040 ADC1 Data Register E & F 32
0x044 ADC1 Data Register G & H 32
0x048 ADC1 Mode Register 32
0x04C Reserved -
0x050 Reserved -
0x054 ADC2 Configuration Register 32
0x058 Reserved -
0x05C ADC2 Correction Register A 32
0x060 ADC2 Correction Register B 32
0x064 ADC2 Correction Register C 32
0x068 ADC2 Correction Register D 32
0x06C ADC2 Correction Register E 32
0x070 ADC2 Correction Register F 32
0x074 ADC2 Correction Register G 32
0x078 ADC2 Correction Register H 32
0x07C ADC2 Data Register A & B 32
0x080 ADC2 Data Register C & D 32
0x084 ADC2 Data Register E & F 32

TPMC533 User Manual Issue 1.0.1 Page 14 of 107
Offset to BAR0
Description
Size (Bit)
0x088 ADC2 Data Register G & H 32
0x08C ADC2 Mode Register 32
0x090 Reserved -
0x094 Reserved -
0x098 ADC3 Configuration Register 32
0x09C Reserved -
0x0A0 ADC3 Correction Register A 32
0x0A4 ADC3 Correction Register B 32
0x0A8 ADC3 Correction Register C 32
0x0AC ADC3 Correction Register D 32
0x0B0 ADC3 Correction Register E 32
0x0B4 ADC3 Correction Register F 32
0x0B8 ADC3 Correction Register G 32
0x0BC ADC3 Correction Register H 32
0x0C0 ADC3 Data Register A & B 32
0x0C4 ADC3 Data Register C & D 32
0x0C8 ADC3 Data Register E & F 32
0x0CC ADC3 Data Register G & H 32
0x0D0 ADC3 Mode Register 32
0x0D4 Reserved -
0x0D8 Reserved -
0x0DC ADC4 Configuration Register 32
0x0E0 Reserved -
0x0E4 ADC4 Correction Register A 32
0x0E8 ADC4 Correction Register B 32
0x0EC ADC4 Correction Register C 32
0x0F0 ADC4 Correction Register D 32
0x0F4 ADC4 Correction Register E 32
0x0F8 ADC4 Correction Register F 32
0x0FC ADC4 Correction Register G 32
0x100 ADC4 Correction Register H 32
0x104 ADC4 Data Register A & B 32
0x108 ADC4 Data Register C & D 32
0x10C ADC4 Data Register E & F 32
0x110 ADC4 Data Register G & H 32
0x114 ADC4 Mode Register 32
0x118 Reserved -
0x11C Reserved -

TPMC533 User Manual Issue 1.0.1 Page 15 of 107
Offset to BAR0
Description
Size (Bit)
ADC Sequencer Registers
0x120 ADC Sequencer Control Register 32
0x124 ADC Sequencer Status Register 32
0x128 Reserved -
0x12C Number of Conversions Register 32
0x130 Conversion Count Register 32
0x134 FIFO Level Register 32
0x138 Reserved -
0x13C Reserved -
0x140 DMA Buffer Base Address Register 32
0x144 DMA Buffer Length Register 32
0x148 DMA Buffer Next Address Register 32
0x14C DMA Status Base Address Register 32
0x150 Reserved -
0x154 Reserved -
DAC Global Registers
0x158 Global DAC Control Register 32
0x15C Global DAC Status Register 32
0x160 Reserved -
0x164 Reserved -
DAC Device Registers
0x168 DAC1 Configuration Register 32
0x16C Reserved -
0x170 DAC1 Correction Register A 32
0x174 DAC1 Correction Register B 32
0x178 DAC1 Correction Register C 32
0x17C DAC1 Correction Register D 32
0x180 DAC1 Data Register A & B 32
0x184 DAC1 Data Register C & D 32
0x188 DAC1 Status Register 32
0x18C DAC1 Mode Register 32
0x190 Reserved -
0x194 Reserved -
0x198 DAC2 Configuration Register 32
0x19C Reserved -
0x1A0 DAC2 Correction Register A 32
0x1A4 DAC2 Correction Register B 32
0x1A8 DAC2 Correction Register C 32
0x1AC DAC2 Correction Register D 32
0x1B0 DAC2 Data Register A & B 32

TPMC533 User Manual Issue 1.0.1 Page 16 of 107
Offset to BAR0
Description
Size (Bit)
0x1B4 DAC2 Data Register C & D 32
0x1B8 DAC2 Status Register 32
0x1BC DAC2 Mode Register 32
0x1C0 Reserved -
0x1C4 Reserved -
0x1C8 DAC3 Configuration Register 32
0x1CC Reserved -
0x1D0 DAC3 Correction Register A 32
0x1D4 DAC3 Correction Register B 32
0x1D8 DAC3 Correction Register C 32
0x1DC DAC3 Correction Register D 32
0x1E0 DAC3 Data Register A & B 32
0x1E4 DAC3 Data Register C & D 32
0x1E8 DAC3 Status Register 32
0x1EC DAC3 Mode Register 32
0x1F0 Reserved -
0x1F4 Reserved -
0x1F8 DAC4 Configuration Register 32
0x1FC Reserved -
0x200 DAC4 Correction Register A 32
0x204 DAC4 Correction Register B 32
0x208 DAC4 Correction Register C 32
0x20C DAC4 Correction Register D 32
0x210 DAC4 Data Register A & B 32
0x214 DAC4 Data Register C & D 32
0x218 DAC4 Status Register 32
0x21C DAC4 Mode Register 32
0x220 Reserved -
0x224 Reserved -
0x228 to 0x2E4 Reserved -
DAC Sequencer Registers
0x2E8 DAC Sequencer Control Register 32
0x2EC DAC Sequencer Status Register 32
0x2F0 Reserved -
0x2F4 Number of Conversions Register 32
0x2F8 Conversion Count Register 32
0x2FC FIFO Level Register 32
0x300 Reserved -
0x304 Reserved -
0x308 DMA Buffer Base Address Register 32

TPMC533 User Manual Issue 1.0.1 Page 17 of 107
Offset to BAR0
Description
Size (Bit)
0x30C DMA Buffer Length Register 32
0x310 DMA Buffer Next Address Register 32
0x314 Reserved -
0x318 Reserved -
0x31C Reserved -
Conversion Signals Registers
0x320 Conversion Clock 1 Generator Register 32
0x324 Conversion Clock 2 Generator Register 32
0x328 Reserved -
0x32C Frame Trigger Generator Register 1 32
0x330 Frame Trigger Generator Register 2 32
0x334 Reserved -
0x338 Reserved -
0x33C Conversion Signals Generator Enable Register 32
0x340 Conversion Signals Generator Output Driver Register 32
0x344 Conversion Signals Source Selection Register 32
0x348 Frame Timer Register 32
0x34C Reserved -
0x350 Reserved -
DIO Registers
0x354 DIO Input Register 32
0x358 DIO Input Filter Debounce Register 32
0x35C DIO Output Register 32
0x360 DIO Output Enable Register 32
0x364 Reserved -
0x368 Reserved -
Interrupt Registers
0x36C Interrupt Enable Register 32
0x370 Error Interrupt Enable Register 32
0x374 DIO Rising Edge Interrupt Enable Register 32
0x378 DIO Falling Edge Interrupt Enable Register 32
0x37C Reserved -
0x380 Reserved -
0x384 Interrupt Status Register 32
0x388 Error Interrupt Status Register 32
0x38C DIO Interrupt Status Register 32
0x390 Reserved -
0x394 Reserved -

TPMC533 User Manual Issue 1.0.1 Page 18 of 107
Offset to BAR0
Description
Size (Bit)
Other Registers
0x398 Global Configuration Register 32
0x39C DIO Pull Resistors Register 32
0x3A0 P14 Back I/O Pull Resistors Register 32
0x3A4 Correction Data EEPROM Control/Status Register 32
0x3A8 Temperature Sensor Trigger Register 32
0x3AC Temperature Sensor Data Register 32
0x3B0 to 0x3F8 Reserved -
0x3FC Firmware Version Register 32
Table 3-3 : Register Space
For the TPMC533-20R the DAC Global Registers, DAC Device Registers and DAC Sequencer
Registers are reserved.

TPMC533 User Manual Issue 1.0.1 Page 19 of 107
Register Bit
Access Type Description
R Read The bit is readable by software.
R/W Read/Write The bit is readable and writeable by software.
R/C Read/Clear The bit is readable by software.
The bit is set by firmware. Software may clear the bit by writing a ‘1’.
R/S Read/Set The bit is readable by software.
Software may set this bit to ‘1’. The bit is cleared by firmware.
Table 3-4 : Register Bit Access Types
When reading reserved register bits, the value is undefined.
Reserved register bits shall be written as '0'.
3.2.1.1 ADC Global Registers
The following registers exist only once and deal with all ADCs on-board the TPMC533.
3.2.1.1.1 Global ADC Control Register (0x000)
The Global ADC Control Register provides control options for each ADC (for all eight ADC Channels of each
ADC) on-board the TPMC533.
Bit Symbol Description Access Reset
Value
31:4 - Reserved - -
3 ADC4_CONV_REQ ADC4 Conversion Request
Refer to the ADC1 Conversion Request bit for description. R/S 0
2 ADC3_CONV_REQ ADC3 Conversion Request
Refer to the ADC1 Conversion Request bit for description. R/S 0
1 ADC2_CONV_REQ ADC2 Conversion Request
Refer to the ADC1 Conversion Request bit for description. R/S 0
0 ADC1_CONV_REQ
ADC1 Conversion Request
Write ‘1’ to start the conversion of the eight ADC Channels
of ADC1.
Before requesting ADC1 Conversion, software should check
the ADC1 Busy Bit to be clear in the Global ADC Status
Register.
This bit is self-clearing.
Note: If ADC1 is configured to operate in Sequencer
Mode ADC1 Conversion Requests are ignored.
R/S 0
Table 3-5 : Global ADC Control Register

TPMC533 User Manual Issue 1.0.1 Page 20 of 107
3.2.1.1.2 Global ADC Status Register (0x004)
For each ADC (for all eight ADC Channels of each ADC) on-board the TPMC533, status information can be
read from this read-only register.
Bit Symbol Description Access Reset
Value
31:4 - Reserved - -
3 ADC4_BUSY ADC4 Busy
Refer to the ADC1 Busy bit for description. R 0
2 ADC3_BUSY ADC3 Busy
Refer to the ADC1 Busy bit for description. R 0
1 ADC2_BUSY ADC2 Busy
Refer to the ADC1 Busy bit for description. R 0
0 ADC1_BUSY
ADC1 Busy
Set when
•analog sampling is in progress
•data is transferred from the ADC
If ADC1 Operating Mode is set to "Manual Mode" in the
corresponding ADC Mode Register, this bit is set by writing
to ADC1_CONV_REQ in the Global ADC Control Register.
This bit must be read as '0' before data can be read from the
corresponding ADC Data Register.
R 0
Table 3-6 : Global ADC Status Register