Texas Instruments TMS320C8 Series User manual

TMS320C8x
Software Development Board
Installation Guide
Literature Number: SPRU150B
Manufacturing Part Number: D418027-9741 revision C
January 1997
Printed on Recycled Paper

Running Title—Attribute Reference
ii
IMPORTANT NOTICE
Texas Instruments (TI) reserves the right to make changes to its products or to discontinue any
semiconductor product or service without notice, and advises its customers to obtain the latest
version of relevant information to verify, before placing orders, that the information being relied
on is current.
TIwarrantsperformanceofitssemiconductorproductsandrelatedsoftwaretothespecifications
applicableatthetimeofsaleinaccordancewithTI’sstandardwarranty.Testingandotherquality
control techniques are utilized to the extent TI deems necessary to support this warranty.
Specific testing of all parameters of each device is not necessarily performed, except those
mandated by government requirements.
Certain applications using semiconductor products may involve potential risks of death,
personal injury, or severe property or environmental damage (“Critical Applications”).
TI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, INTENDED, AUTHORIZED, OR
WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT APPLICATIONS, DEVICES
OR SYSTEMS OR OTHER CRITICAL APPLICATIONS.
Inclusion of TI products in such applications is understood to be fully at the risk of the customer.
UseofTI products in such applicationsrequiresthe written approval of anappropriateTI officer.
Questions concerning potential risk applications should be directed to TI through a local SC
sales office.
In order to minimize risks associated with the customer’s applications, adequate design and
operating safeguards should be provided by the customer to minimize inherent or procedural
hazards.
TI assumes no liability for applications assistance, customer product design, software
performance, or infringement of patents or services described herein. Nor does TI warrant or
representthatanylicense,eitherexpressorimplied,isgrantedunderanypatentright,copyright,
mask work right, or other intellectual property right of TI covering or relating to any combination,
machine, or process in which such semiconductor products or services might be or are used.
Copyright 1997, Texas Instruments Incorporated

iii
Preface
Read This First
About This Manual
This manual tells you how to install the TMS320C8x (’C8x) software
development board (SDB). The SDB is a peripheral component
interconnect (PCI) plug-in card that helps you evaluate characteristics of the
’C8x digital signal processor (DSP) to determine how it will meet the
requirements of your given application.
The SDB offers you a simple application programming interface (API) to
control data flow across the host bus. You can also use the SDB as a
development tool to create software and applications for the ’C8x on a PC t .
The board is designed for use on PCI PC-based computers with
Windows NT
t .
This manual assumes you are familiar with working in a Windows NT
environment and understand general and technical PC and multimedia
processes and terminology.
How to Use This Manual
Use this manual for instruction on installing and using the SDB. This book is
divided into three distinct parts:
- Introductory information, consisting of Chapter 1, describes hardware
and software requirements necessary to install and use the SDB and
provides an overview of the ’C8x SDB and its components.
- Instructive information, consisting of Chapters 2, 3, and 4, describes
procedures for installing the SDB, running the board diagnostics
application, and troubleshooting problems with your SDB.
- Reference material, consisting of Appendixes A and B, provides
supplementary SDB information and a glossary.

Notational Conventions / Information About Cautions and Warnings
iv
Notational Conventions
In this document, program listings, program examples, and interactive
displays are shown in a special typeface. Examples use a bold
version of the special typeface for emphasis; interactive displays use a
bold version of the special typeface to distinguish commands that you
enterfromitemsthatthesystemdisplays(such asprompts, commandoutput,
error messages, etc.).
Here is an example of a system prompt and a command that you might enter:
d:\setup.exe
Information About Cautions and Warnings
This book contains cautions and warnings.
This is an example of a caution statement.
A caution statement describes a situation that could potentially
damage your software or equipment.
This is an example of a warning statement.
A warning statement describes a situation that could potentially
cause harm to you.
The information in a caution or a warning is provided for your protection.
Please read each caution and warning carefully.

Related Documentation From Texas Instruments
v Read This First
Related Documentation From Texas Instruments
The following books describe the TMS320C8x software development board
(SDB) and related support tools. To obtain a copy of any of these TI
documents, call the Texas Instruments Literature Response Center at (800)
477–8924. When ordering, please identify the book by its title and literature
number.
TMS320C80 Digital Signal Processor Data Sheet (literature number
SPRS023) describes the features of the TMS320C80 and provides
pinouts, electrical specifications, and timings for the device.
TMS320C80 (MVP) Code Generation Tools User’s Guide (literature
number SPRU108) provides information about the features and
operation of the linker and the master processor (MP) and parallel
processor (PP) C compilers and assemblers. It also includes a
descriptionofthecommonobjectfile format(COFF)andshowsyouhow
to link MP and PP code.
TMS320C80 (MVP) C Source Debugger User’s Guide (literature number
SPRU107) describes the ’C8x master processor and parallel processor
C source debuggers. This manual provides information about the
features and operation of the debuggers and the parallel debug
manager; it also includes basic information about C expressions and a
description of progress and error messages.
TMS320C8x Emulator Installation Guide (literature number SPRU148)
provides installation instructions for the ’C8x emulator card and the C
source debugger software for PC systems running Windows NT, and
describes release enhancements and miscellaneous changes for the
current release.
TMS320C8x Master Processor User’s Guide (literaturenumberSPRU109)
provides information about the master processor (MP) features,
architecture, operation, and assembly language instruction set; it also
includes sample applications that illustrate various MP operations.
TMS320C8x Multitasking Executive User’s Guide (literature number
SPRU112) provides information about the multitasking executive
softwarefeatures,operation,andinterprocessorcommunications;italso
includes a list of task error codes.
TMS320C8xParallelProcessorUser’sGuide (literaturenumberSPRU110)
provides information about the parallel processor (PP) features,
architecture, operation, and assembly language instruction set; it also
includes software applications and optimizations.

Related Documentation From Texas Instruments / FCC Warning / Trademarks
vi
TMS320C8x Software Development Board Programmer’s Guide
(literature number SPRU178) provides descriptions of hardware
functions, complete API references, theory of operation, and example
code for the SDB.
TMS320C8x System-Level Synopsis (literature number SPRU113)
describes the ’C8x features, development environment, architecture,
memory organization, and communication network (the crossbar).
TMS320C80 Transfer Controller User’s Guide (literature number
SPRU105) provides information about the transfer controller (TC)
features, functional blocks, and operation; it also includes examples of
block write operations for big- and little-endian modes.
TMS320C80 Video Controller User’s Guide (literature number SPRU111)
provides information about the video controller (VC) features,
architecture, and operation; it also includes procedures and examples
for programming the serial register transfer (SRT) controller and the
frame timer registers.
TVP3020VideoInterface PaletteDataManual (literaturenumberSLAS080)
provides information about the TVP3020 Video Interface Palette
features, register set, operation, and characteristics.
FCC Warning
This equipment is intended for use in a laboratory test environment only. It
generates, uses, and can radiate radio frequency energy and has not been
testedfor compliancewiththe limits ofcomputingdevices pursuanttosubpart
Jofpart15ofFCC rules,whicharedesignedtoprovidereasonableprotection
against radio frequency interference. Operation of this equipment in other
environments may cause interference with radio communications, in which
case the user at his own expense will be required to take whatever measures
may be required to correct this interference.
Trademarks
IBM and PC are trademarks of International Business Machines Corporation.
MS, MS-DOS, Windows, and Windows NT are registered trademarks of
Microsoft Corporation.
Pentium is a trademark of Intel Corporation.

Obtaining Technical Support
vii Read This First
Obtaining Technical Support
Before contacting Texas Instruments Technical Support, have the following
information ready:
- Model number of your SDB
- Serial number located on the back side of your board
- Software version number located on the TMS320C8x SDB system
software media
- Brand name, model number, and speed of the computer in which the
board is installed
- Computer’s PCI BIOS version
- Amount of memory in your computer system
- Version of the software and operating environment that you are using
(such as Windows NT)
- Type of video or audio signal being captured or processed
- Cabling arrangement of input and output devices connected to the board
Once you have this information ready, contact Texas Instruments Technical
Support as specified in the
If You Need Assistance section that follows.

If You Need Assistance
viii
If You Need Assistance . . .
- World-Wide Web Sites
TI Online http://www.ti.com
Semiconductor Product Information Center (PIC) http://www.ti.com/sc/docs/pic/home.htm
DSP Solutions http://www.ti.com/dsps
320 Hotline On-line t http://www.ti.com/sc/docs/dsps/support.html
- North America, South America, Central America
Product Information Center (PIC) [phone]
TI Literature Response Center U.S.A. [phone]
Software Registration/Upgrades [phone] Fax: [phone]
U.S.A. Factory Repair/Hardware Upgrades [phone]
U.S. Technical Training Organization [phone]
DSP Hotline [phone] Fax: [phone] Email: [email protected]
DSP Modem BBS [phone]
DSP Internet BBS via anonymous ftp to ftp://ftp.ti.com/mirrors/tms320bbs
- Europe, Middle East, Africa
European Product Information Center (EPIC) Hotlines:
Multi-Language Support [phone] Fax: [phone] Email: [email protected]
Deutsch [phone] or [phone]
English [phone]
Francais [phone]
Italiano [phone]
EPIC Modem BBS [phone]
European Factory Repair [phone]
Europe Customer Training Helpline Fax: [phone]
- Asia-Pacific
Literature Response Center [phone] Fax: [phone]
Hong Kong DSP Hotline [phone] Fax: [phone]
Korea DSP Hotline [phone] Fax: [phone]
Korea DSP Modem BBS [phone]
Singapore DSP Hotline Fax: [phone]
Taiwan DSP Hotline [phone] Fax: [phone]
Taiwan DSP Modem BBS [phone]
Taiwan DSP Internet BBS via anonymous ftp to ftp://dsp.ee.tit.edu.tw/pub/TI
- Japan
Product Information Center +0120-81-0026 (in Japan) Fax: [phone] (in Japan)
+03-3457-0972 or (INTL) 813-3457-0972 Fax: [phone] or (INTL) 813-3457-1259
DSP Hotline [phone] or
(INTL) 813-3769-8735 Fax: [phone] or (INTL) 813-3457-7071
DSP BBS via Nifty-Serve Type “Go TIASP”
- Documentation
Whenmakingsuggestions orreportingerrors indocumentation,please includethefollowing informationthatis onthetitle
page: the full title of the book, the publication date, and the literature number.
Mail: Texas Instruments Incorporated Email: [email protected]
Technical Documentation Services, MS 702
P.O. Box 1443
Houston, Texas 77251-1443
Note: When calling a Literature Response Center to order documentation, please specify the literature number of the
book.

Contents
ix
Contents
1 SDB System Requirements and Components 1-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Describes the items that are delivered as part of the SDB kit. Explains the hardware and
software requirements necessary to install and use the SDB.
1.1 System Requirements 1-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.2 TMS320C8x SDB PCI Plug-In Card 1-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.3 Peripheral Cables 1-6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2 Installing the TMS320C8x SDB 2-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Describes step-by-step procedures for installing the SDB. Explains how to install the board,
how to connect the peripherals (if applicable), and how to install the software.
2.1 Before Starting the Installation Process 2-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.2 Step 1: Installing the SDB Card Into Your PC 2-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.3 Step 2: Connecting Peripheral Cables to the SDB 2-5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.4 Step 3: Installing the System Software 2-8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.5 Where to Go From Here 2-9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3 Running the Board Diagnostics 3-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Explains how to run the SDB board diagnostics application to verify the operation of the major
componentsoftheSDB,suchasaudiocaptureandplayback,videodisplay,videocapture,and
host communications.
4 Troubleshooting 4-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Lists primary error conditions and explains how to correct them.
A SDB Connector Pinouts A-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Lists the pinouts for each peripheral cable connector for the SDB.
A.1 S-VHS Input Pinout A-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A.2 VGA Pass-Through Pinout A-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A.3 Graphics Output Monitor Pinout A-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A.4 Audio I/O Pinout A-5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
B Glossary B-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Defines acronyms and key terms used in this book.

Notes, Cautions, and Warnings
x
Figures
1–1 TMS320C8x SDB Components 1-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1–2 TMS320C8x SDB Connectors 1-5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1–3 S-VHS-to-RCA Adapter Cable 1-6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1–4 VGA Pass-Through Cable 1-7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1–5 Audio Breakout Cable 1-8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2–1 TMS320C8x SDB Installation 2-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3–1 SDB Diagnostics Dialog Box 3-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A–1 S-VHS Input Connector A-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A–2 VGA Pass-Through Connector A-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A–3 Graphics Output Monitor Connector A-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A–4 Audio I/O Connector A-5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cautions
Minimizing Static Shock 2-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Obstructions 2-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connecting the Wrong Connectors 2-5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Warning
Minimizing Personal Injury Risk 2-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1-1
SDB System Requirements and Components
This chapter explains the hardware and software requirements necessary to
install and use the software development board (SDB), and it describes the
items that are delivered as part of the TMS320C8x SDB kit.
Topic Page
1.1 System Requirements 1-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.2 TMS320C8x SDB PCI Plug-In Card 1-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.3 Peripheral Cables 1-6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chapter 1

System Requirements
1-2
1.1 System Requirements
Toinstallandusethe’C8xSDB,youneedtheitemsinthefollowingchecklists,
which include the hardware and software requirements plus the contents of
the ’C8x SDB kit.
Hardware checklist
Host PentiumPC
Memory Minimum of 16M bytes of RAM plus at least 20M bytes of hard-disk
space (32M bytes of RAM is recommended for optimum perfor-
mance)
Monitor High-resolution multisync monitor
Slot One full-length peripheral component interconnect (PCI) slot
Peripheral cable Graphics output monitor cable (supplied by monitor manufacturer)
For more information about the graphics output monitor cable, see
Section 1.3,
Peripheral Cables.
Required hardware CD-ROM drive
Microsoftcompatible mouse
Optional hardware AnEGA-orVGA-compatiblegraphicsdisplaycardandalargemon-
itor (17-inch or 19-inch)
TheCsourcedebuggerhastwooptionsthatallowyoutochangethe
overallsizeofthedebuggerdisplay.For moreinformation aboutde-
bugger options, see the
TMS320C80 (MVP) C Source Debugger
User’s Guide
.
Software checklist
Operating system Windows NT (version 3.5 or later)
PC software tools ThefollowingtoolsareusedwiththeSDBtowriteprogramsthatuse
the’C8xforimage processing, graphics generation, audio process-
ing, and standard digital signal processor (DSP) applications:
Master processor (MP) optimizing C compiler
Parallel processor (PP) optimizing C compiler
MP reduced instruction set computer (RISC) assembler
PP algebraic assembler
Common object file format (COFF) linker for MP and PP code

System Requirements
1-3 SDB System Requirements and Components
PP code compactor and register allocator
Multitasking executive for host communications
’C8x SDB kit checklist
PCI plug-in card TMS320C8x SDB PCI plug-in card
For information about the PCI plug-in card, see Section 1.2,
TMS320C8x SDB PCI Plug-In Card .
Peripheral cables S-VHS-to-RCA adapter cable
VGA pass-through cable
Audio breakout cable
For information about the cables that connect to optional
peripherals, see Section 1.3,
Peripheral Cables.
CD-ROMs TMS320C8x SDB System Software. This CD-ROM contains the
following system software:
- Device driver for Windows NT. The kernel mode driver is re-
sponsible for all communications between the host and the
SDB.
- Csourcedebuggers.Thedebuggersallowreal-time,in-circuit
emulation of the ’C8x DSP. There are two types of debugger:
onefortheMPandoneforthePPs.Seethe
TMS320C80(MVP)
CSourceDebuggerUser’sGuide
formoredetailedinformation.
- Boardresetutility.Thiscommand-lineutilityisexecutedonthe
host and resets the SDB hardware and the ’C8x DSP.
- Board diagnostics utility. This is a graphical user interface
(GUI) program for Windows NT that tests the major hardware
components of the SDB.
- Peripherallibrary.Thelibraryhasacompletesetofapplication
programminginterface (API) functions calledby’C8x programs
to control the hardware peripherals. See the TMS320C8x Soft-
ware Development Board Programmer’s Guide
for more de-
tailed information.
Installing the SDB software sets up the debugger environment for
using the SDB card.
TMS320C80 (MVP) Online Reference . This CD-ROM provides
easy access to paper-based reference documents that have been
adapted for online viewing.
Documentation Three books and the registration card

TMS320C8x SDB PCI Plug-In Card
1-4
1.2 TMS320C8x SDB PCI Plug-In Card
The ’C8x PCI plug-in card is a printed-circuit assembly (PCA) that plugs into
aPCIexpansionslotonyourcomputer’smotherboard.TheSDBcardconsists
of the following components (see Figure 1–1):
- 40-MHz TMS320C80 DSP
- 8M bytes of DRAM
- 2M bytes of VRAM (for high-resolution display)
- Audiocodec(forthecaptureandplaybackofaudiosignalsatsamplerates
of up to 48 kHz in 16-bit stereo)
- Video capture, consisting of a complete video front end for capturing
National Television Standards Committee (NTSC) or phase alternation
line (PAL) video in a composite or S-VHS component format
- Video display, consisting of a video interface palette (VIP), which drives
monitorresolutionsupto1600×1200at8BPP(bitsperpixel)witha60-Hz
refresh rate
- PCI interface
- Memory controller
Figure 1–1. TMS320C8x SDB Components
TMS320C80 DSP
Memory
controller
DRAM
VRAM
PCI bus
64 16
32
I/O bus
Audio
codec
Video
display
Video
capture
PCI
interface
32
16
16
64
64
64
16
64
32
16
64

TMS320C8x SDB PCI Plug-In Card
1-5 SDB System Requirements and Components
The SDB card also contains IEEE 1149.1 standard emulation support, and it
has connectors for peripheral cables. Figure 1–2 illustrates the retaining
bracketwiththeconnectorsprovidedforconnectingoptionalperipheralstothe
SDB.
The relationship between the connectors, the cables, and the input/output
(I/O) peripheral devices is described in Section 1.3,
Peripheral Cables . The
procedures for installing the hardware are given in Chapter 2,
Installing the
TMS320C8x SDB
.
Figure 1–2. TMS320C8x SDB Connectors
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
PC motherboard
(4-pin mini-DIN)
S-VHS input
(8-pin mini-DIN)
VGA pass-through
(15-pin D-sub)
Graphics output monitor
(8-pin mini-DIN)
Audio I/O
(4-pin mini-DIN)
S-VHS input
(8-pin mini-DIN)
VGA pass-through
(15-pin D-sub)
Graphics output monitor
(8-pin mini-DIN)
Audio I/O
SDB PCI plug-in card
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Peripheral Cables
1-6
1.3 Peripheral Cables
The peripheral cables connect the SDB to external input or output sources.
The cables you need depend on the external hardware (video camera, moni-
tor, audio equipment, for example) you will be connecting to the SDB. The fol-
lowing table lists the peripheral cables and their corresponding connectors.
ÁÁÁÁÁÁÁ
Á
ÁÁÁÁÁ
Á
Connector
ÁÁÁÁÁÁÁÁÁÁÁ
Á
ÁÁÁÁÁÁÁÁÁ
Á
Cable
ÁÁÁÁÁÁÁ
Á
ÁÁÁÁÁ
Á
Supplier
ÁÁÁÁÁÁÁ
Á
ÁÁÁÁÁ
Á
ÁÁÁÁÁÁÁ
4-pin mini-DIN
ÁÁÁÁÁÁÁÁÁÁÁ
Á
ÁÁÁÁÁÁÁÁÁ
Á
ÁÁÁÁÁÁÁÁÁÁÁ
S-VHS-to-RCA adapter cable
ÁÁÁÁÁÁÁ
Á
ÁÁÁÁÁ
Á
ÁÁÁÁÁÁÁ
TMS320C8x SDB
ÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁ
8-pin mini-DIN
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
VGA pass-through cable
ÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁ
TMS320C8x SDB
ÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁ
15-pin D-sub
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
Graphics output monitor cable
ÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁ
Monitor manufacturer
ÁÁÁÁÁÁÁ
Á
ÁÁÁÁÁ
Á
ÁÁÁÁÁÁÁ
8-pin mini-DIN
ÁÁÁÁÁÁÁÁÁÁÁ
Á
ÁÁÁÁÁÁÁÁÁ
Á
ÁÁÁÁÁÁÁÁÁÁÁ
Audio breakout cable
ÁÁÁÁÁÁÁ
Á
ÁÁÁÁÁ
Á
ÁÁÁÁÁÁÁ
TMS320C8x SDB
Thepurposeofthissectionistofamiliarizeyouwiththeperipheralcables.See
Section2.3,
ConnectingPeripheralCablestotheSDB, for installation instruc-
tions.
S-VHS-to-RCA adapter cable
The S-VHS-to-RCA adapter cable (see Figure 1–3) consists of a 4-pin mini-
DIN connector that connects the luminance and chrominance signals to RCA
jacksfor composite video sources. The adapter cable is compatiblewith most
composite video cameras. When you are using a video source that requires
a BNC connection, you can combine the adapter cable with a BNC-to-RCA
adapter. The BNC-to-RCA adapter connector is not available through TI but
can be purchased through a cable supplier.
Figure 1–3. S-VHS-to-RCA Adapter Cable

Peripheral Cables
1-7 SDB System Requirements and Components
VGA pass-through cable
The VGA pass-through cable (see Figure 1–4) connects the 15-pin VGA out-
put of the host display adapter to the 8-pin mini-DIN VGA pass-through con-
nector of the board. When this cable is attached, settings in the display sub-
map control whether the display output is taken from the SDB, from the host’s
display adapter, or from both.
Figure 1–4. VGA Pass-Through Cable
Graphics output monitor cable
The graphics output monitor cable is a 15-pin D-sub cable that connects the
graphicsoutputboardconnectortothemonitor.Thiscableisnecessarytodis-
playgraphics outputto a monitorand issuppliedby themonitormanufacturer.

Peripheral Cables
1-8
Audio breakout cable
The audio breakout cable (see Figure 1–5) separates audio connections by
using an 8-pin mini-DIN connector to RCA plugs. The audio cable includes
connections for stereo line-out, line-in, and auxiliary-in.
The cable is compatible with any audio equipment that connects to standard
RCA jacks. The RCA plugs can be used with CJ11-to-dual-RCA connectors
for audio components requiring phone plug connections. The CJ11-to-dual-
RCA connectors cable is not available through TI but can be purchased
through a cable supplier.
Figure 1–5. Audio Breakout Cable

2-1
Installing the TMS320C8x SDB
This chapter contains step-by-step procedures for installing the TMS320C8x
software development board (SDB). You begin by installing the board, con-
necting the peripherals (if applicable), and, finally, installing the software.
Topic Page
2.1 Before Starting the Installation Process 2-2. . . . . . . . . . . . . . . . . . . . . . . . .
2.2 Step 1: Installing the SDB Card Into Your PC 2-4. . . . . . . . . . . . . . . . . . . .
2.3 Step 2: Connecting Peripheral Cables to the SDB 2-5. . . . . . . . . . . . . . . .
2.4 Step 3: Installing the System Software 2-8. . . . . . . . . . . . . . . . . . . . . . . . . .
2.5 Where to Go From Here 2-9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chapter 2

Before Starting the Installation Process
2-2
2.1 Before Starting the Installation Process
Before you begin installing the ’C8x SDB, do the following tasks:
- Verify that you received the items listed as part of the ’C8x SDB kit in
Chapter 1.
- Make sure that the system in which you are installing the SDB meets the
equipment and software requirements listed in Chapter 1.
- To help avoid equipment damage, read and follow the instructions in this
sectionforcontrollingstaticelectricityandavoidingobstructionsthatcould
prevent you from installing the SDB.
Note:
If you find any items missing or damaged, contact Texas Instruments im-
mediately. See
If You Need Assistance in the Preface for the appropriate
phone numbers.
Controlling static electricity
Minimizing Static Shock
Specialhandlingmethods and materialsshould be usedto prevent
equipment damage. You should be familiar with identification and
handling of ESD-sensitive devices before attempting to perform
the procedures described in this manual.
Tohelpavoidproblemsresultingfromstaticelectricity,followtheseguidelines:
- Store the board in its antistatic bag until you are ready to use it.
- Keeptheantistaticbag for storing or transferring the board between com-
puters.
- Wear a properly connected ground strap at all times when handling the
SDB.