Texas Instruments FPC401 User manual

1
SNLU222B–December 2016–Revised September 2019
Submit Documentation Feedback Copyright © 2016–2019, Texas Instruments Incorporated
FPC401 and FPC402 Evaluation Module (EVM) User’s Guide
User's Guide
SNLU222B–December 2016–Revised September 2019
FPC401 and FPC402 Evaluation Module (EVM) User’s
Guide
The information and/or drawings set forth in this document and all rights in and to inventions disclosed
herein and patents which might be granted thereon disclosing or employing the materials, methods,
techniques, or apparatus described herein are the exclusive property of Texas Instruments. No disclosure
of information or drawings shall be made to any other person or organization without the prior consent of
Texas Instruments.
Contents
1 Hardware Description and Setup .......................................................................................... 2
1.1 Power Configuration................................................................................................ 2
1.2 Communication Protocol Configuration.......................................................................... 3
2 FPC401 EVM GUI Description and Setup................................................................................ 5
2.1 Installation ........................................................................................................... 6
2.2 Initializing Communication......................................................................................... 6
2.3 Local FPC Read and Write........................................................................................ 8
2.4 Remote Access on Downstream Modules....................................................................... 9
2.5 Input and Output Status and Configuration.................................................................... 10
2.6 Interrupt Configuration and Monitoring ......................................................................... 11
2.7 LED Configuration................................................................................................. 12
2.8 Prefetch Configuration............................................................................................ 13
2.9 Data-Driven Interrupt Configuration............................................................................. 14
2.10 Scheduled Write Configuration.................................................................................. 15
Trademarks
All trademarks are the property of their respective owners.

Hardware Description and Setup www.ti.com
2SNLU222B–December 2016–Revised September 2019
Submit Documentation Feedback
Copyright © 2016–2019, Texas Instruments Incorporated
FPC401 and FPC402 Evaluation Module (EVM) User’s Guide
1 Hardware Description and Setup
The general procedure for setting up the FPC401 and FPC402 Evaluation Modules (EVM) is described in
the following sections.
Figure 1. FPC40xEVM – Top and Bottom
1.1 Power Configuration
Configure the power illustrated by Figure 2.
1. If the LDO is used to power the FPC, enable the LDO through header J8 and connect the LDO output
to VDD1 using header J4 (note that each header connection is rated for 1 A of current). Make sure
headers J7 and J13 are disconnected. The LDO has a maximum rated current of 1.5 A, so if the
cumulative QSFP/SFP module current draw is greater than that, the LDO may not be used.
2. If the LDO is not used and the FPC is powered through an external supply, configure the J8 header to
disable the LDO and connect VIN to VDD1 using header J7 (note that each header connection is rated
for 1 A of current). Make sure headers J4 and J13 are disconnected.
3. If USB power is used to power the FPC, ensure the LDO and VIN and disconnected from VDD1
(disconnect headers J4 and J7). Connect the 3.3 V of the MSP430 microcontroller to VDD1 through
header J13. Note that a typical computer USB port is only able to supply up to 100 mA which will be
enough to power the FPC and passive modules (that is, DAC); but it will not be enough to power active
SFP+ and QSFP+ modules which are plugged in.
4. To set VDD2 to 3.3 V, connect it to VDD1 through header J2. To operate at lower host-side supply
voltages (down to 1.8 V), connect an external supply to the header or test point loop (TP3).
5. The FPC401EVM and FPC402EVM includes a TPS2561 power switch which is used to selectively
enable and disable 3.3-V power to the SFP and QSFP ports. The FPC controls this power switch with
its GPIO pins. To supply power to ports 0 and 1 (QSFP+ ports and LEDs), configure the FPC GPIO0
high logic output to enable the power switch. Similarly, configure GPIO1 to high logic to enable power
for ports 2 and 3 (SFP+ ports and LEDs). Alternatively, supply 3.3 V externally through the test points
(TP4 and TP5). Note that the ground is shared with the board.
6. GPIO2 and GPIO3 are connected to the fault outputs of the power switch, and hence should be set as
inputs or left unconfigured.

www.ti.com Hardware Description and Setup
3
SNLU222B–December 2016–Revised September 2019
Submit Documentation Feedback Copyright © 2016–2019, Texas Instruments Incorporated
FPC401 and FPC402 Evaluation Module (EVM) User’s Guide
Figure 2. Power Block Diagram – Configured for LDO Use
1.2 Communication Protocol Configuration
The following sections describe how to configure the FPC401EVM and FPC402EVM for I2C and SPI
protocols.
1.2.1 I2C Configuration
For I2C communication with the onboard MSP430, refer to Figure 3 and configure the board based on the
following procedure.
1. Leave the PRTCL_SEL pin disconnected (header J3).
2. Connect the MSP430 SCL and SDA to the FPC SCL and SDA through header J12. The SPI header
(J9) should be disconnected.
3. Connect the 2.7-kΩpullup resistors through header J1.
4. Connect the VDD2 pin to the VDD1 pin through header J2.
5. Connect the ADDR_N pin to GND through header J2 with the provided jumper wire.
For I2C communication with an external host controller, disconnect the MSP430 SDA and SCL. Connect
the FPC SDA and SCL pins to the SDA and SCL pins of the host controller. Only connect the onboard
pullup resistors if the host board does not have pullups.
To control multiple EVMs, connect all the SDA and SCL pins together. Only one board should have the
MSP430 and pullup resistors connected to these pins. The ADDR_N of the first device should be tied to
GND as shown in Figure 3 . Connect DONE_N pin of the first device to the ADDR_N of the second
device, and the DONE_N pin of that device to the following device in a daisy-chained fashion until all
ADDR_N pins are connected. Connect the final DONE_N pin to GND. See the data sheet for more details
on how I2C is configured.
Figure 3. I2C Configuration

Hardware Description and Setup www.ti.com
4SNLU222B–December 2016–Revised September 2019
Submit Documentation Feedback
Copyright © 2016–2019, Texas Instruments Incorporated
FPC401 and FPC402 Evaluation Module (EVM) User’s Guide
1.2.2 SPI Configuration
For SPI communication with the onboard MSP430, refer to Figure 4 and configure the board based on the
following procedure.
1. Connect the PRTCL_SEL pin to GND through header J3.
2. Connect the MSP430 MISO, MOSI, SCK, and SS_N pins to the FPC MISO, MOSI, SCK, and SS_N
pins through header J9. The I2C header (J12) should be disconnected.
3. Connect the VDD2 pin to the VDD1 pin through header J2.
For SPI communication with an external host controller, disconnect the MSP430 MOSI, MISO, SCK, and
SS_N pins. Connect the FPC MOSI, MISO, SCK, and SS_N pins to the MOSI, MISO, SCK, and SS_N
pins of the host controller.
To control multiple EVMs with SPI, connect all the SCK and SS_N pins to a single MSP430 SCK and
SS_N pins. Daisy chain the MOSI and MISO pins so that the MOSI of the MSP430 connects to the MOSI
of the first device, the MISO of the first device connects to the MOSI of the second device, and so on, until
the final device's MISO connects to the MISO of the MSP430. See the data sheet for more details on how
SPI is configured.
Figure 4. SPI Configuration

www.ti.com FPC401 EVM GUI Description and Setup
5
SNLU222B–December 2016–Revised September 2019
Submit Documentation Feedback Copyright © 2016–2019, Texas Instruments Incorporated
FPC401 and FPC402 Evaluation Module (EVM) User’s Guide
2 FPC401 EVM GUI Description and Setup
The FPC401 EVM GUI is used to program both FPC401EVM and FPC402EVM. The general procedure
for setting up the FPC401 GUI is described in the sections below.
Figure 5. FPC401 EVM GUI

FPC401 EVM GUI Description and Setup www.ti.com
6SNLU222B–December 2016–Revised September 2019
Submit Documentation Feedback
Copyright © 2016–2019, Texas Instruments Incorporated
FPC401 and FPC402 Evaluation Module (EVM) User’s Guide
2.1 Installation
The FPC401 EVM GUI has two installers. The Setup_FPC401_EVM.exe installer does not contain the
National Instruments Run-Time Engine and requires web access to download the NI run-time engine if the
computer does not already have this installed. The Setup_FPC401_EVM_with_RTE.exe installer is a
larger file that contains the run-time engine and does not require web access. Select the appropriate
installer and follow the installer wizard to install the FPC401 EVM GUI.
2.2 Initializing Communication
To initialize communication with the FPC401EVM, first select the number of FPC401s under FPC Count
and the protocol (I2C or SPI), highlighted by Figure 6. Click OPEN LINK to establish communication with
the MSP430 through USB and initialize the device. In I2C mode, this will configure the MSP430 and
automatically configure the I2C addresses of all connected FPC401s so that each one has a unique
address. In SPI mode, this will configure the MSP430 and establish the length of the SPI message. Each
time the hardware configuration changes, the link must be reestablished. For example, connecting
additional FPC401s or changing the communication from I2C to SPI requires the link to be reestablished.
The TOGGLE LED button will toggle the LED (D7) for a visual indication that the USB communication is
working. The text in the bottom of the GUI should say CONNECTED and turn green after USB
communication is established. Note that this means that the computer is communication with the MSP430
but does not necessarily mean that communication is established with the FPC401.
The CLOSE LINK button will terminate USB communication.
Figure 6. Communication Control

www.ti.com FPC401 EVM GUI Description and Setup
7
SNLU222B–December 2016–Revised September 2019
Submit Documentation Feedback Copyright © 2016–2019, Texas Instruments Incorporated
FPC401 and FPC402 Evaluation Module (EVM) User’s Guide
The top right section of the GUI highlighted by Figure 7 controls the FPC(s) being programmed by all
controls in this GUI. The Instance # selects which FPC is being controlled, starting at instance 0. The Port
#selects which port is being configured, where 0 is the port 0 of FPC instance 0, and 4 is port 0 of FPC
instance 1. The Broadcast switch will broadcast commands to all FPCs if set to 1. Note that if a command
that targets a port is broadcasted, not all ports will be modified. Instead, only ports that match the local
port of the selected instance are modified. For example, broadcasting a command that targets port 5 (local
port 1 of instance 1) will affect ports 1, 5, 9, 13, and so forth.
Figure 7. FPC Instance and Port Selection

FPC401 EVM GUI Description and Setup www.ti.com
8SNLU222B–December 2016–Revised September 2019
Submit Documentation Feedback
Copyright © 2016–2019, Texas Instruments Incorporated
FPC401 and FPC402 Evaluation Module (EVM) User’s Guide
2.3 Local FPC Read and Write
To read and write to local FPC registers, select the Local Reads and Writes tab. Select the instance
number and register offset address to be read or written to. To write, select a value using the radio boxes
in the WRITE COMMAND section or type the desired hex value and click EXECUTE WRITE. To read,
click EXECUTE READ. The RESET FPC REGISTERS button will reset the instance's local FPC registers.
Note that performing a register reset in I2C mode will restore the default I2C address of the device and the
link must be closed and reopened to restore normal GUI operation.
Figure 8. FPC401 GUI – Local Reads and Writes

www.ti.com FPC401 EVM GUI Description and Setup
9
SNLU222B–December 2016–Revised September 2019
Submit Documentation Feedback Copyright © 2016–2019, Texas Instruments Incorporated
FPC401 and FPC402 Evaluation Module (EVM) User’s Guide
2.4 Remote Access on Downstream Modules
To perform a remote access read or write on a downstream port, select the Downstream Reads and
Writes tab. Select the port number, downstream device I2C address, and register offset address. To write,
select a value using the radio boxes in the WRITE COMMAND section or type the desired hex value and
click EXECUTE WRITE. To read, click EXECUTE READ. The Set I2C Rate switch will toggle the I2C rate
of the downstream between 100 kHz (SFP) and 400 kHz (QSFP).
Figure 9. FPC401 GUI – Downstream Reads and Writes

FPC401 EVM GUI Description and Setup www.ti.com
10 SNLU222B–December 2016–Revised September 2019
Submit Documentation Feedback
Copyright © 2016–2019, Texas Instruments Incorporated
FPC401 and FPC402 Evaluation Module (EVM) User’s Guide
2.5 Input and Output Status and Configuration
To control the input, output, and GPIO pins, select the I/O Status and Configuration tab. The Enable
Periodic Update button will update the indicator of each input, GPIO, and output periodically set by the
Update Period (ms) slider. This will also update the Port's Aggregated Interrupt Flag which determines if
any interrupt of the selected port has been triggered. To modify the state of the GPIOs, modify the GPIO
0/1/2/3 Set drop-down menus and click SET GPIOS. To modify the state of the outputs, modify the OUT
A/B Set drop-down menus and click SET OUTPUTS.
Figure 10. FPC401 GUI – Input, Output, GPIO Status, and Control

www.ti.com FPC401 EVM GUI Description and Setup
11
SNLU222B–December 2016–Revised September 2019
Submit Documentation Feedback Copyright © 2016–2019, Texas Instruments Incorporated
FPC401 and FPC402 Evaluation Module (EVM) User’s Guide
2.6 Interrupt Configuration and Monitoring
To configure the port's interrupts, select the Input Pin Interrupt tab. To enable input pin interrupts, select
the port, input trigger source, and trigger edge. Click SET to configure. To check and clear the status of all
of the interrupts of the selected port, click UPDATE AND CLEAR. Some of these interrupts are configured
in other sections.
To enable the SDA and SCL instances stuck at 0 interrupts, click SDA STUCK ENABLE and SCL STUCK
ENABLE buttons. These buttons enables the interrupts for all ports of the selected instance. To clear
these interrupts, a port reset must be issued using the RESET PORT button, highlighted in Figure 12.
Figure 11. FPC401 GUI – Interrupt Control
Figure 12. FPC401 GUI – Port Reset

FPC401 EVM GUI Description and Setup www.ti.com
12 SNLU222B–December 2016–Revised September 2019
Submit Documentation Feedback
Copyright © 2016–2019, Texas Instruments Incorporated
FPC401 and FPC402 Evaluation Module (EVM) User’s Guide
2.7 LED Configuration
To configure the LEDs, select the LED Settings tab. Select the port number, LED number, LED state and
click the SET button in the LED STATE section. If configured in the PWM or BLINK mode, use the Duty
Cycle (%) slider and click SET in the PWM MODE SETTINGS section. Since the PWM duty cycle is 0 by
default, the LEDs will not be visible until this is modified. In BLINK mode, configure the On Time and Off
Time and click SET under the BLINK MODE SETTINGS section. To synchronize the LEDs, click the
SYNCHRONIZE LEDS button at the bottom of the page. This will automatically forward the LED clock for
synchronization across multiple devices. See the data sheet for more details.
Note that in the FPC401EVM and FPC402EVM the GPIO0 and GPIO1 must be set to drive high logic to
enable the power switch that powers the LEDs and modules.
Figure 13. FPC401 GUI – LED Settings
Figure 14. LED Mapping

www.ti.com FPC401 EVM GUI Description and Setup
13
SNLU222B–December 2016–Revised September 2019
Submit Documentation Feedback Copyright © 2016–2019, Texas Instruments Incorporated
FPC401 and FPC402 Evaluation Module (EVM) User’s Guide
2.8 Prefetch Configuration
To configure prefetching, select the Prefetch Settings tab. The PREFETCH GLOBAL SETTINGS
determines the port number, device I2C address (0xA0 or 0xA2), prefetch length, and starting register
offset address for both the periodic prefetch and interrupt-driven prefetch features. The Prefetch Length
input controls the number of bytes to be prefetched and the Prefetch Offset (Hex) input determines the
starting register offset address.
In the PERIODIC PREFETCH SETTINGS section, enter the prefetch period in milliseconds and click
START PREFETCH. A period of 0 ms is a one-time prefetch. To stop the periodic prefetch, click the
STOP PREFETCH button. This will not clear the gate bit, so any downstream read in the prefetched range
will read from the FPC memory. To reset the gate bit and force the FPC to read from the downstream
port, click RESET GATE. See the data sheet and programmer's guide for more details about prefetching.
In the INTERRUPT DRIVEN PREFETCH section, select the input that will trigger the interrupt-driven
prefetch, the edge transition of the selected input, and click SET. After an interrupt-driven prefetch is
successful, to clear the gate bit and perform another one, click the RE-ARM button. This will also clear the
interrupt.
Figure 15. FPC401 GUI – Prefetch Settings

FPC401 EVM GUI Description and Setup www.ti.com
14 SNLU222B–December 2016–Revised September 2019
Submit Documentation Feedback
Copyright © 2016–2019, Texas Instruments Incorporated
FPC401 and FPC402 Evaluation Module (EVM) User’s Guide
2.9 Data-Driven Interrupt Configuration
To configure data-driven interrupts, select the Data-Driven Interrupt Settings tab. The FPC is able to
monitor up to four bytes per port, and the monitored byte index is controlled by the Byte Number input.
Select the port number, register address to be monitored and the bits to be monitored and click SET. Note
that the monitored register address must be within the prefetched range for the selected port. Click
CHECK / CLEAR DATA to determine which bits of the four monitored bytes triggered the interrupt. This
will also clear the interrupt.
Figure 16. FPC401 GUI – Data-Driven Interrupt Control

www.ti.com FPC401 EVM GUI Description and Setup
15
SNLU222B–December 2016–Revised September 2019
Submit Documentation Feedback Copyright © 2016–2019, Texas Instruments Incorporated
FPC401 and FPC402 Evaluation Module (EVM) User’s Guide
2.10 Scheduled Write Configuration
To perform a scheduled write to one or more downstream ports, select the Scheduled Write tab. Select
the port number, device address, register offset address, and write value and click EXECUTE
SCHEDULED WRITE. This will issue a write to the selected port, and may be broadcasted to write to
multiple ports across multiple FPC instances. The CONFIGURE COMMON SCHEDULED WRITE section
works similarly, but the user may also select which of the ports to be written, allowing writing to all four
local ports simultaneously.
Figure 17. FPC401 GUI – Scheduled Write Control

Revision History www.ti.com
16 SNLU222B–December 2016–Revised September 2019
Submit Documentation Feedback
Copyright © 2016–2019, Texas Instruments Incorporated
Revision History
Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Original (November 2016) to B Revision ................................................................................................ Page
• First public release. ....................................................................................................................... 2

www.ti.com Revision History
17
SNLU222B–December 2016–Revised September 2019
Submit Documentation Feedback Copyright © 2016–2019, Texas Instruments Incorporated
Revision History
Changes from Original (November 2016) to B Revision ...................................................................................................... Page
• First public release. ....................................................................................................................... 2

IMPORTANT NOTICE AND DISCLAIMER
TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATA SHEETS), DESIGN RESOURCES (INCLUDING REFERENCE
DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS”
AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD
PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate
TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable
standards, and any other safety, security, regulatory or other requirements.
These resources are subject to change without notice. TI grants you permission to use these resources only for development of an
application that uses the TI products described in the resource. Other reproduction and display of these resources is prohibited. No license
is granted to any other TI intellectual property right or to any third party intellectual property right. TI disclaims responsibility for, and you
will fully indemnify TI and its representatives against, any claims, damages, costs, losses, and liabilities arising out of your use of these
resources.
TI’s products are provided subject to TI’s Terms of Sale or other applicable terms available either on ti.com or provided in conjunction with
such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable warranties or warranty disclaimers for
TI products.
TI objects to and rejects any additional or different terms you may have proposed. IMPORTANT NOTICE
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2022, Texas Instruments Incorporated